Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Is this electricly OK?

Posts

Is this electricly OK?

#1

Is this electricly OK?

RogerC

>I wish to add a small red light bulb on my lathe to remind me to unplug it when not in use.

The light should always be on, while the machine is plugged, regardless of whether the motor is running or not.

Here is a picture of what I am planning to do, and am wondering if this is electrically OK?


img

Re: Is this electricly OK?

#2

Re: Is this electricly OK?

Bill Howatt

>Yes, it is electrically correct.

When you wire the light, plug, switch, motor you should connect the shell of the bulb (the threaded part if a regular light bulb) to the neutral pin of the plug assuming a 120V circuit. This is the wider or silver pin on the plug. The hot connection, the narrower or brass pin on the plug should go to the centre connection of the light bulb, the switch and then to the motor. The switch always opens/closes on the hot wire.

You didn't show a ground but the third U-shaped pin should be connected to any exposed metal parts of mounting boxes and the motor frame. This is typically done with a green wire in cords or a bare wire in romex (typical house wiring).

Bill

Re: Is this electricly OK?

#3

Depends

Mark Mandell - Gone Round In Jersey

>What's your lathe's voltage, 115 or 220? If 115 it will be ok so long as you wire the light fixture in parallel. If you put it in "series", you'd force the bulb's filament to carry all the juice going to the lathe, and your lathe would stop when the bulb burned out. Not likly a good idea. Note also that the switch you have drawn is surplus unless you plan on switching the whole lathe on and off with that switch.

If your lathe is 220, you will have to have a 4-wire supply and circuit [2 hots, 1 common, and 1 ground] which calls for a special fixture and plug because you would need the common wire available to safely take a 115 branch off the 220 line using only one of the hot leads.

Other way is to plug your lathe into a switched outlet with a telltale light in or on the switch and just leave the lathe plugged into the special outlet. That way, even with a 220 circuit you can use the simpler machine wire. You've still got to have a "common" conducter available in the outlet/switch box for the 220 application.

Re: Is this electricly OK?

#5

Re: Is this electricly OK?

RogerC

>Oops,

should have mentioned:

-it is 115V

-it is grounded (green wire runs from wall plug, screwed to the switch's metal box, then to motor housing)

-the switch itself is just a plain light switch

Re: Is this electricly OK?

#6

neon indicator light?

JohnKJordan in East TN

>RogerC,

A neon bulb is commonly used for a pilot/indicator light application for 110v and 220v. Wired across the mains, the current use is low, the heat is low, they are designed to run at AC line voltage without any additional components, and they last nearly forever.

You can get them in a variety of configurations and colors - a nice type comes in an electrically safe insulated mount with attached wire leads and snaps into a hole drilled into sheet metal.

I searched Google for neon pilot light and this was the first link:

http://www.action-electronics.com/pilotlights.htm

JKJ

Re: Is this electricly OK?

#7

OK

Mark Mandell - Gone Round In Jersey

>You unplug (first |;-} )

For a plug telltale: Get your light wire into the switch box through a clamp or other restraining device. Connect your light's hot (black) wire to the upstream switch terminal (were it comes in from the plug) and splice into the white lead on the supply with a wirenut.

You ARE putting your little lite out of the lathe's "Kill Zone" right?

If you wire it wrong, the light will simply tell you when the lathe is turned on. |;-}}

mm

Re: Is this electricly OK?

#8

Re: neon indicator light?

Bill Howatt

>I'll agree with what you said except for the "last forever". They can often fairly quickly start flickering. It was one reason I didn't buy a plasma TV, reminded me of 9 million neon bulbs!

Bill

Re: Is this electricly OK?

#9

Re: No Bill...

Al Stokka - Cambridge, Iowa

>"...you should connect the shell of the bulb (the threaded part if a regular light bulb) to the neutral pin of the plug assuming a 120V circuit."

Bill,

Gotta disagree with you on this one. The neutral wire should be connected to the shell of a lampholder, not the hot wire.

Al

Re: Is this electricly OK?

#10

I think that's what he said._____

Rod Peterson -- Ormond Beach

>

Re: Is this electricly OK?

#11

PS

Mark Mandell - Gone Round In Jersey

>I did something similar with my chop saw. I made a big cabinet with integrated dust hood and fold-out extension wings for my LS-1211, plus lots of duct-free storage underneath. I do have people and their kids visiting my shop now and then, and I just wasn't comfortable with this big-ass 12" blade hanging there like a tragedy waiting to happen. Since I had already worked integral halogen spot work lights into the hood, I decided to wire them and the power outlet for the saw into a single switch that is concealed behind the cabinet doors (that can be child-proofed. Lights were wired such that they are only one when the saw's outlet is switched on. I then never have to worry about somebody's kid playing with the saw and amputating a hand whilst parent and I are talking shop and preoccupied. Lights are off . . the saw's safe.

You putting your little telltale at the shop exit to remind you on the way out? |;-}}}

Re: Is this electricly OK?

#12

mission accomplished

RogerC

>Thanks for the help guys,

just connected everything together and it works fine.

I decided to go with a small dome light, about 1/2" in diameter, not really sure if it is neon or not. It has two unlabeled 4" wires coming out of the base and seems to work well either way. The cost was about three and a half bucks.

It looks pretty darn good.

Thanks again.

Re: Is this electricly OK?

#13

Re: PS

RogerC

>Yup, I'm doing this for safety reasons.

I enclosed the old open motor (it has oil cups!) in a wooden cabinet to protect it from eating dust.

For fire reasons, I would rather have it enclosed in a metal cabinet, but it is not an option at this time.

The light is there to remind me to unplug the darn thing before I leave the shop.

no juice --- no fire

It might seem a bit "anal", but I'd rather be safe than sorry.

Re: Is this electricly OK?

#14

Certainly what I meant

Bill Howatt

>

Re: Is this electricly OK?

#15

Re: I apologize, Bill.

Al Stokka - Cambridge, Iowa

>Bill,

I read your earlier post at least three times concluding that it said to wire the screw base backwards. Rereading it this morning I find that it is, indeed, correct. Sorry.

Al

Re: Is this electricly OK?

#16

No problem at all, Al!

Bill Howatt

>