Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Options?

Posts

Options?

#1

Options?

Mark Mandell - Gone Round In Jersey

>I (The Dummy Who Knows Better) tried to apply a shellac sealing coat while the humidity was about 99% this morning. Yeah, you guessed it, white haze from trapped moisture over most of the piece.

So, aside from an alky rubdown too remove the fogged resin, anyone have any other solves on this one?

Thanks

mm

[thinking I aught to just go back to turning in New Jersey]

Re: Options?

#2

Well Mark........

George@Colonel's Workshop-Havertown PA

>Good Afternoon Mark,

That also happens to the worst of us, DAMHIKT. An alcohol rub down on a hot day is a good way to cool off. Do it with Jack Daniels and its even better. :<) I think you have to rub it down.

George

Re: Options?

#3

Re: Well George . . . .

Mark Mandell - Gone Round In Jersey

>I've seen your work so don't pull that "worst-of-us" shtick. |;-}}

Bit short on Jack, wonder if Tullimore Dew will do?

Re: Options?

#4

Re: Options?

John N

>also, the more humidity, the more alcohol in the cut.

the coats cure fast and you can then sneek up on the thickness.

Re: Options?

#5

Ah Mark, "Give Every Man His Dew".

George@Colonel's Workshop-Havertown PA

>Geeze Mark,

Its been over 20 years since I had even a wee drop. Thank God for beer, though, which I can drink and enjoy.

George

Re: Options?

#6

Re: Coats

Mark Mandell - Gone Round In Jersey

>Gotcha, John,

What I'm doing is sealing the cured Watco oil under a very thin layer of dewaxed garnet shellac in prep for the waterborne topcoats, in this case, the last of my Fuhr 355.

Can't build the shellac as it's prone to crack (called "cold checking") under waterbornes. I learned about this the hard way when it happened to my Lady's Morris chair posted here a while ago. Literally had to strip and refinish about 60% of the chair; it was NOT FUN.

Oh well, guess there's only one way to "git thar from heah." Now where's that bag of rags . . . . . ?

mm

Re: Options?

#7

Re: Wee Drops

Mark Mandell - Gone Round In Jersey

>er for those Northern Big I'landers who're still taukin foony tree hundrt yeahs after loosein ta tha Brits!!

Ya'll not be droppin' tha Dew, Bucko! Thet's fer kickin' back neet an' feelin' the born!!!

|;-}}}}}

mm

Re: Options?

#8

Re: Options?

Bill Hammond, Oregon Coast

>You could always start a decoupage project, just lay some newsprint on it to soak up the excess moisture;)

Re: Options?

#9

Re: Options?

Ken Oakley-Sunny St. Cloud, Fla

>Not sure about shellac but when the humidity is high and I need to spray lacquer I will get my wifes's hair dryer, (I don't have one--No hair), and make a few passes over the suface I want to spray. I have had a bit of luck doing the same on a surface that has already been coated and blushed and gotten rid of the blush.

Re: Options?

#10

Jason Roehl in Lafayette, IN

One possibility...

Jason Roehl in Lafayette, IN

>...would be to get it into a dry environment (~50% R.H.) and just mist some DNAlcohol on the shellac, enough to get it damp, but not run. This could soften/open the blushed shellac enough to let the moisture out. I've heard of this working with lacquer, no reason I can think of why it shouldn't with shellac.

Jason

Re: Options?

#11

Re: Done

Mark Mandell - Gone Round In Jersey

>Got out the alk, the gloves and a few old cotton socks. Worked it down to remove the haze. Let dry and rehit with a new coat.

All is forgiven.

Tomorrow it gets finished.

Thanks to all

mm