Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Small parts storage for large tools?

Posts

Small parts storage for large tools?

#1

JL

Small parts storage for large tools?

JL

>How do ya'll do yours? I was thinking about buying some magnets and building some small boxes to stick on the sides of tools. I just want something to store the allen wrenches and jointer knife setters on the jointer and something to store the allen wrenches and spare parts on the band saw.

Re: Small parts storage for large tools?

#2

Re: Small parts storage for large tools?

NickB

>I don't even both with boxes-just a magnet. My sliding TS has a scoring blade that is adjusted up and down with an allen key which I keep stuck to the top of the rip fence with a 1/4" rare earth magnet. I don't seem to have a whole lot of adjusting tools/jigs that need to be at hand all the time (knife setting jigs, etc. just go in a box somewhere, as I don't use them all that often).

Nick

Re: Small parts storage for large tools?

#3

It works for me, with some reservation

Bill Tindall, E.TN

>But, the tools will become magnitized. Not an issue for the allen wrench used to remove the band saw blade guard but it was for some other applications. I tried holding my lathe tools on the bed with a mag knife holding strip. It worked great to keep the tools from falling off the bed. When I ground the tool the grinding dust stuck-not so great.

Re: Small parts storage for large tools?

#4

Re: Small parts storage for large tools?

George@Colonel's Workshop-Havertown PA

>Good Morning JL,

It used to drive me nuts, trying to locate the extra jointer knives, grinding cones for the mortising chisels, knife setters, replacement thrust bearings, extra blade guards, brushes, and resaw guides. I made a finger jointed box of white oak and labelled it "Power Tool Widgits" with a black sharpie. Now everything like that goes into one place, organized and instantly available.

George

Re: Small parts storage for large tools?

#5

Re: Small parts storage for large tools?

Kneale Brownson in sunny N. MI

>I use the heavy plastic bags small automotive parts come in--an alternative might be the smaller freezer ZipLock bags--and tape them to the tool with painter's trim tape. For example, my jointer has a baggie taped to one side of the cabinet with the tools required for a blade change inside. You can see through the bag to see what tools are there.

Re: Small parts storage for large tools?

#6

PVC pipes and plastic bins

Mark Goodall - ATL - tooljunkie

>I have a whole bunch of "custom" made holders on my tools. I often make then from a short length of Sched-40 PVC pipe with a cap at one or both ends. Then I attach them to the tools in various ways (screws, holes,pipe clamps, etc).

I also use small odd plastic bins... the kind you buy at Target in the kitch area. And I'll place them at strategic points on the machine. I have one, for instance, firmly attached to the top of the flat belt cover on the back of my Delta 14" bandstand.

One of these days I should take photos of all the PVC do-dads I've got in the shop.

Happy Woodworking!

Re: Small parts storage for large tools?

#7

Re: Small parts storage for large tools?

Charles Wiggins

>I use ziplock baggies too. I keep all my TS & joiner accessories on a 4x4' pegboard on the nearest wall. I hang the wrenches up there as well and all of the Allen wrenches go into baggies. I even hang up my earplug headset in a baggie (keeps it dust-free when not in use). I just poke a hole in the upper corner of the bag with the peg I hang it on. If you get the heavy-duty ones they last a couple of years with moderate usage.

This also works with manuals. I keep a lot of manuals in 2 gallon ziplocks and hang them by a peg or nail. That way, when it's time to do maintenance on the lawnmower, I'm not looking around in a pile of dust covered papers. It's hanging from the storage rack in the garage along with the manual for the weedeater and the extra spools of line. I also keep a lot of stuff in small candy boxes, and all of my router accessories (wrenches, collars, indiv. wrapped bits, etc.) are in a kid's shoe box.

I've done a couple of custom boxes, but generally, I find that stuff to be a waste of time unless the items are really delicate or terribly disorganized.

Re: Small parts storage for large tools?

#8

Re: Small parts storage for large tools?

David Haywood

>I agree with the others, rare earth magnets will do a great job of holding tools on/or close to the machine they are needed on. If they become magnetized, and this is a problem, you can demagnetize them with a small unit that can be purchased at Woodcraft stores and probably many others. I have had problems with turning tools becoming magnetized and sticking to the tool rest while I was turning. The demagnetizer is an easy fix for this as long as the tool is not too large.

Re: Small parts storage for large tools?

#9

Re: Small parts storage for large tools? *LINK*

Kent in Emmaus, PA

>Magnetic parts trays make great catchalls for small pieces and tools. I have one on just about every machine.


Magnetic Parts Trays

Re: Small parts storage for large tools?

#10

Re: Small parts storage for large tools?

JohnKJordan in East TN

>I agree - I love these for allen wrenches and other small things near the lathe. I stick one on a wire shelf that would not hold small parts otherwise. JKJ

Re: Small parts storage for large tools?

#11

Lee Gordon

Re: Small parts storage for large tools?

Lee Gordon

>I use those little tin boxes that Altoids mints come in. For example, I have one for all the safety keys for my stationary power tools.

Re: Small parts storage for large tools?

#12

Re: Small parts storage for large tools?

Tim Jones

>For a bunch of good suggestions on how to store tools/stuff check out Woodsmith mag vol 29/174 'small tool storage'. I like the wall mounted magnetic strip described there- a bunch of rare earth magnets embedded/hidden in a wood strip with a protective layer of cork or wood to keep tools from directly contacting the magnets. That helps keep the tools from becoming magnetized and keeps sharp things sharp as there is no metal on metal contact. Also check out http://benchcrafted.com for ready to use magnetic wood strips. They have some nice knife/tool holders. I got a maple one and you can't even see the glue line- looks like one chunk of 'magic' wood. While these are aimed at kitchen use, sometimes we deserve to add some class to our shops too...