Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

New Jointer FINALLY setup,.. almost

Posts

New Jointer FINALLY setup,.. almost

#1

New Jointer FINALLY setup,.. almost

Brian in Brighton

>Well, after sitting in a box for 2 months, the Grizzly G0490 is finally setup. I removed the cutterhead to change to the Shelix head, found a few shims that worry me. I can't get the bearings off the orginal shaft as the press fit is too much. I will see if I get to use the neighbors press to help them out. I will check the elevation with a dial indicator on the new shelix head to make it parallel to the beds at install. I had not thought about that before. With a standard cutterhead the blade can be tweeked to be straight and parallel. The Shelix head can only be shimmed.

So has anyone else seen this problem?

Brian in Brighton

Re: New Jointer FINALLY setup,.. almost

#2

Rick L

Re: You can adjust the tables!

Rick L

>The Grizzly G0490 Jointer is a parallelogram desing and each table has 4 point adjustment so you other options. You can throw away the shims with that set up. It will take a machined straight edge and feeler gauge to realign the tables. It will take you a few hours if you've never done it before. On the Delta there are double setscrews so they may do the same thing. Over each adjustment cam is a set screw. Another set screw is typically put in over the first one. You must remove the top set screw entirely to loosen the bottom on. Failure to do will score the cam.

Re: New Jointer FINALLY setup,.. almost

#3

Re: You can adjust the tables!

Jim Smith

>Hello Brian, Did the same thing to mine last week, and it also had three shims under the drive side, don't worry to much about it, at least they took the time to shim it up like it should be. A small three jaw puller will pull the bearings off easily, some Auto Parts stores will loan you one or rent for small sum. Haven't had time to totally align with long straight edge, but I am very pleased with the cut I am getting now,I hated the cut from the knives, thats why I spent the money to change it out, I would not recommend this jointer to anyone without the Byrd or shelix head. Good luck email if you need anything. Jim Smith

Re: New Jointer FINALLY setup,.. almost

#4

Re: You can adjust the tables!

Brian in Brighton

>Thanks. Now I was just wondering what to do with the old cutterhead. If I was the manufacturer (hey guys this is for you!), I would offer to buy the old heads with all the gibs in place back from a customer on the condition that it is in like new condition for 50% of the replacement part price. Ay least it saves them from becoming another thing in the shop for SWMBO to point at and ask why it's here and what it is :-)

Brian in Brighton

Re: New Jointer FINALLY setup,.. almost

#5

Perfect timing!

Mike Schwing from Md.

>My shelix head should arrive in a couple weeks for this same jointer. Now I know what I'll be facing. Thanks men!

Re: New Jointer FINALLY setup,.. almost

#6

Re: Some hints

Brian in Brighton

>Mike, You will need to lower the infeed table in order to slide out the cutterhead from the pulley end. It just slides out nicely. Look out for the shims. I hope to get mine complete this week.

Brian in Brighton

Re: New Jointer FINALLY setup,.. almost

#7

Re: Done!!

Brian in Brighton

>OK. I had the neighbor use his super-duper puller set to help get the bearings off the shaft. I tapped them onto the new Shelix head. I cleaned the shims and put everything back together. By using my cool Align-It kit I measured the cutterhead to be parallel within .001 to the bed. I also measured the infeed and outfeed tables to be parallel across the bed to within .001. I have not turned it on yet, but would consider it a success.

Now what do I do with the old 4 blade cutterhead? Anyone want to buy it cheap to replace a 3 blade model?

Brian in Brighton