mini lathes
David Haywood
>Does anyone have opinions on which mini lathe would the best one for a beginner who wants to start turning? They run from Grizzly to Delta, most look the same and the specs don't help either.
Knowledge You Can Build On — Est. 1998
mini lathes
David Haywood
>Does anyone have opinions on which mini lathe would the best one for a beginner who wants to start turning? They run from Grizzly to Delta, most look the same and the specs don't help either.
Re: mini lathes
eliot d
>You can't go wrong with the Jet mini. I believe it is the least expensive , too.The variable speed is more convenient but more expensive. It tends to loose power at the slow speeds, too. Most turners love it , though. I have the non -variable and leave it at a high speed mostly for spindle and small boxes. But I have a large variable speed lathe, so I don't really need the variable feature. You can certainly make a stand for it, but if you don't want to bother, there's a stand for it that costs about $120( I think), easily comes apart for travel, and is excellent.
Re: mini lathes
john lucas
>I will second the Jet Mini. The other lathes are pretty nice but the Jet has been a proven performer in reliability and ease of use. I have a Carbo-tec, Jet mini and Nova Comet mini lathe. I would rate the Nova as better but they don't make it anymore. The Vicmarc VM100 is also an excellent mini lathe and may be the best but it is noticeably more expensive than the Jet.
The off brand mini lathes often have problems with odd spindle thread sizes or getting replacement parts when something does break.
Re: mini lathes
Jack
>Wood Mag just did an article on getting started turning. They liked the Rikon at $250
Turning Forum *LINK*
Ron in Drums PA
>Check us out here
Turning Forum
Re: mini lathes
Jim Dillon
>David,
While I don't do much turning, I do like my Jet mini lathe. I have the nonvariable speed model and it is really no big deal to change the belt. I built a bench from Shop Notes for mine and that has worked well.
If you haven't already, you might post the same question on WoodCentral's turning forum that you get to by clicking on the link at the left of this screen under Messageboards. Good luck and have fun shopping.
Jim
Re: mini lathes
Nelson
>I bought the Jet 1220 and its great, 12 in swing,3/4 hp. Woodcraft special for October is the Rikon for $199.
Hi David...
David Yoho
>I know you already have a nice lathe. I'll bet the guys where you work can fill you in well too. So, you just in the market for a mini or is this for someone else? It's for sure you have the space in that nice shop of yours!!
The folks over on the Turning Forum will be glad to help. Try there too.
David
Re: Hi David...
David Haywood
>Hi David,
I am looking for information for someone else. My wife's uncle lives in southwest VA and therefore has limited access to anything but the big box stores. He left me a message asking questions about the Ridig, Grizzly, Delta, Jet, etc. I don't know anything about the Grizzly and Ridig, which is why I posted the question. My choice "of course" would be the Jet. Rikon has some issues that even the low price can't overcome. Delta is overpriced and there customer service is non-existent since the take-over by BD.
You still working all the overtime? I wondered why we haven't seen you at the store. You working on anything new?
David
What are the issues with RIkon?
Jack
>
Re: mini lathes
JL
>I like the variable speed Jet Mini. I also like the variable speed General 25-200 "Maxi" lathe.
Re: mini lathes
JohnKJordan in East TN
>I needed a second late to lug around and chose the Jet Mini, non-VS. I'm happy with it - it's well-built and does a fine job. About $200.
JKJ
Re: Hi David...
David Yoho
>I thought it sounded like it was for someone else. Yes, still working the OT but not quite as much as before. Getting ready to start a new project soon. I'll probably need some supplies, so I'll probably be seeing you.
Take care,
David
Re: mini lathes
Tony - Memphis
>I have enjoyed my Jet too. I can't offer any comparison to other brands, but the Jet has worked fine. No issues. I bought the extension too. I mostly turn furniture legs and small items (handles and such). Oh, mine is the non VS model.
Tony
Please don't consider this a crass commercial....
Art Silva
>but most of you already know that I work at the Woodcraft store in Allentown, Pa. The Rikon is on sale this month for $199.99, and since Woodcraft is a supporter of this site, you can link from here directly and give Ellis some credit. Also the latest issue of Wood magazine has an article on mini lathes, and their statement is: "Rikon is selling a Cadillac for the price of a Chevy". As Yogi liked to say: "You could look it up".