Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

rusted pool light conduit

Posts

rusted pool light conduit

#1

rusted pool light conduit

Joseph Mulherin

>I am going to replace the pool light. Found out that the conduit leading from connection box above ground to light is rusted thru and is probably plugged with dirt...cannot push thru the fish tape to connect the new cable and pull the cable up so I can reconnect it and use the new light.

I tried probing in the water(chilly) with a probe and found out that the plug is about 40" inside the conduit. and is underground about 3 1/2ft. Thought of cutting the concrete decking but saw is short and only cut 3"...have about another 1/2 to 2" left to cut thru. Thought about trying to blow air down the upper part and possibly clear out the dirt and not have to dig it up.... Previous cable has been already pulled out, so I cannot use it to connect the new cable and pull it thru. Suggestion PLEASE.....

Re: rusted pool light conduit

#2

Re: Blow water down the upper part.

Al Crandall

>I used a 1/2" od plastic flex tube from the home center connected to my garden hose to drill a hole under a 12' wide concrete drive. Unless your conduit is plugged with large gravel, I would think a strong water stream would drill through the dirt and flush it up the conduit eventually.

Re: rusted pool light conduit

#3

Re: rusted pool light conduit

Kneale Brownson in sunny N. MI

>BFH or sledge and a cold chisel to get the plug you've already cut out of the concrete deck. I'd think you want to replace the conduit, not just run a new wire through it. You don't want live power running loose around a swimming pool, and a frayed conduit could result in broken insulation on your wire. I'd redo it with plastic, even if you have to break out a bunch of the concrete. It's relatively easy to pour new concrete in a patch situation. BTDT to fix plumbing under a slab and under a pool deck.

Re: rusted pool light conduit

#4

Re: rusted pool light conduit

Gary Dean Bordeaux

>The conduit is always full of water. So unless you had plugged the conduit hole in the niche your pool has been leaking water for a while. The best fix is new plastic conduit. This is usually the results of a home built pool and not following NEC and local codes. Over the years I have seen everything from EMT, red brass, and plastic. Do not use EMT!

Re: rusted pool light conduit

#5

Re: rusted pool light conduit

Joseph Mulherin

>Thanks, Kneale, that is just what I AM going to do...replace the conduit with plastic PVC. I think I can connect the stub of the conduit from the back of the light using EMT couplings and to the other end the same way...instead of chopping out all that concrete. Have already cut the deck about three feet by 12"wide. Am going to dig out the dirt(sand here in Indio, CA) and make the corrections.

I agree with the other response in that there might possibly be a fraying of the cable sheathing in the future and cause an electrical shock to someone.

Re: rusted pool light conduit

#6

Thats it ! . . .

SteveM

>Just used one to go under sidewalk and part of the drive. Just make sure you dig out a pretty long trench at the starting point or that length of PVC will bind up between the bottom of the slab and the top of the grade behind you. Unless you've got drainage from your trench you might have to wait for it to drain or bail it out. The material washes out better and faster if the trench is empty.

Re: rusted pool light conduit

#7

Re: rusted pool light conduit

Joseph Mulherin

>Thank all you guys. It is much appreciated to have such knowledge available when we have a problem that needs others opinions and data.

I have to congratulate Ellis for setting up such a good beneficial website.

Re: rusted pool light conduit

#8

Re: rusted pool light conduit

Joseph Mulherin

>Gary, the pool was constructed in 1966 for $2,500. When we moved in in 1973 the contract was in the laundry cabinet. So, the metal conduit lasted for many years anyway. Back then they did not have the materials we use nowadays...pvc for plumbing and the other gray pvc used in electrical conduiting. But, like I said in another message, I am going to break out the concrete decking, dig down about 30", cut off the conduit and replace it with the pvc piping and couple the pieces together with emt couplings(or something else) I am going to my local BORG and ask what I should use for this setup.

Again, thanks guys for your knowledgable responses.

Re: rusted pool light conduit

#9

Re: rusted pool light conduit

Joseph Mulherin

>I chopped down into the decking near the pool and found out that the conduit was embeded into the gunite when the poll was formed to make the pool in 1966.

Ergo, I have decided to blow out the conduit with air pressure to clear out the blockage of sand and push thru the fish tape from the pool up to the wall connection box. Then, I shall connect a wire to the tape and withdraw the tape to the pool entrance. Shall then connect the new pool cable to the wire and draw the cable up thru the present conduit and connect it to the electric. I do not think it wiii cause any problems in the future with any fraying of the sheathing on the cable and the pool light will operate as specified.

The first conduit was embed into the gunite when the pool was made and is too much of a problem to clear it out and install new plastic conduit. Hey, this in an older pool built in 1966 and I am just trying to refurbish it to modern standards.

Called my local pool const. co. and the man said to run the tape back up the conduit FROM the pool to the box/ connect a wire to it and return...then connect the new cablke to the wire and redraw it up to the upper box and make the conection to make the light operate.

I have misgivings on this, but if it works , and does not cause any problems with shock, then it will work....

Re: rusted pool light conduit

#10

Re: rusted pool light conduit

Larry Clinton

>If I were doing this, I would try to clear out the conduit enough so that I could pull a 14 / 2 with ground UF romax wire through the conduit. This has the advantage of the extra sheathing around the wire vs the single wires. The UF is rated for direct burial without conduit and should not "fray" or suffer damage nearly as easily. I am sure code requires this be connected to a GFI breaker so would not be a "shock" hazard if the breaker performs its task properly anyhow.

Re: rusted pool light conduit

#11

Re: rusted pool light conduit

Joseph Mulherin

>Larry, the cable with the light replacement is about 3/8" with black, white and green inside it. The covering is thick and the inside wires are insulated too, so I do not think there is going to be any problem with pulling it thru the hard rusted conduit. I did want to cut out the old conduit and replace it with some gray plastic electrical conduit, but the conduit is inside the gunite when the pool was being made. And, after chopping for a couple hrs I gave up and decided that since the old cable was not harmed when it was pulled out, I could just replace the old with the new and seal the conduit opening with a silicone to prevent any more water being inside the conduit. Also have a black gummy putty electricians use for such too. That will go over the silicone. Am draining the pool down th where I can work...will report how things came out when finished.

Re: rusted pool light conduit

#12

Re: rusted pool light conduit

Joseph Mulherin

>OK, Larry, this morning and early afternoon I was in the pool trying to get the tape thru...no luck...could get my 1/4" plumbing cable thru...tried connecting the light cable to it and tried to pull it back thru conduit....NOT... tried several methods of getting tape thru...blew air, scrounged with plumbing cable....nothing. So, I am calling in my grandson who has run elec. in Fla and see what he thinks. Hey, I am a retired const men from the early 50s and am not stupid. I know how to do things, but this has be befuddled.

Re: rusted pool light conduit

#13

Re: rusted pool light conduit

Joseph Mulherin

>OK, I have been given the order by the wife to call the Pool company and have one of their guys do the job. Makes me feel like a dodo.....

Re: rusted pool light conduit

#14

Re: rusted pool light conduit

Joseph Mulherin

>OK, called the pool company and was told that they were two weeks away from answering any appointments....too busy for my problem. Called an electrician and was told to do exactly what I had determined to do in the first place at the beginning of this fiasco.

So, I went and purchased a rubber plug for the conduit and an refilling the pool so we can use the cleaner and keep the pool clean. I am going to rent a Hilti and chop out the gunite over the next two weeks and replace the rusted conduit with plastic and seal it with silicone around the joints. Tried several ways and means to get a cable thru the conduit but was hitting possibly the edge of it and the tape would not go thru....ergo, chop it all out and replace with the plastic.