Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Confusion stacking up with new dado blade

Posts

Confusion stacking up with new dado blade

#1

Confusion stacking up with new dado blade

Dan Mitchell

>Just got a Freud 208 stacked dado set. Never used one before. I'm a bit confused about how to place the blades on the arbor. I understand about the carbide facing forward. The (very brief, image-less) instructions say "If chippers are to be used, place them on with the teeth of the chippers in the gullet of the outside blade. The gullet? Huh? The outside blades have the carbide face. About .5" behind the carbide face (as the blade rotates) is a non-tipped prong. Then there's a gap of about 1.5" until the next carbide face. Each end of the chippers is also 2-pronged, one carbide one not, with a gap of about 1 3/8" between the prongs. Should the 2 prongs of a chipper straddle the carbide & prong tip of the outside blade, or should the 2 prongs of a chipper go in the ~1.5" between outside blade points? It seems like the former, but a couple PICTURES would have been worth a mint here.

Next, it says If more than one chipper is used, rotate every other chipper 90 degrees. OK, so chipper 2 goes on 90 degrees from chipper one, like a + sign. Now where does chipper 3 go, right on top of chipper 1 (i.e., 90 degrees from chipper 2)? The carbides touch if you do that. Seems like you'd want them spaced out evenly around the outer blade. Again, a picture would have been great. If anyone can explain this in words, or if you have some pictures (couldn't find any online using blades like the Freud's) I'd appreciate it.

TIA

Dan

Re: Confusion stacking up with new dado blade

#2

Re: Confusion stacking up with new dado blade

Kirk (KC) Constable

>The body of the chippers should be flat against the body of the neighboring chipper or outside blade. Turn them however you need to so the carbide tips miss each other.

KC

Re: Confusion stacking up with new dado blade

#3

Re: Confusion stacking up with new dado blade

Jim Dillon

>Morning Dan,

While I don't have that particular dado set, I can't imagine it would assemble differently from other brands. If using one chipper, place its carbide tip more-or-less between two of the outside blades carbide teeth, i.e. in the gullet between the two outside teeth. On my set, there is sorta a "sweet spot" where the chipper blade sets absolutely flat against the outside blade without riding up on the welds of the two outside teeth. If using two chippers, do the same thing, but place one of the chippers roughly 90 degrees to the other chipper, again being sure to place the chipper teeth in the gullet of the other outside blade and flat to the outside blade. If using 3 or 4 chippers, orient them all so they are equally spaced from one another. Again, while it isn't critical to be exactly in the middle of the gullet, make sure that the none of the carbide teeth are touching one another and that if you are using 1 or 2 chippers they are flat to the outside blades. As an aside, the same assembly procedure is used when just using the two outside blades to cut a 1/4 inch dado; make sure the teeth do not touch and the blades are flat against one another. Hope this makes some sense.

Jim.

Re: Confusion stacking up with new dado blade

#4

Re: Confusion stacking up with new dado blade

Don Evans

>Hey Dan:

UNPLUG YOUR SAW'S POWER CORD NOW!

The others have answered you correctly but I'll use different wording.

You are correct in saying the first chipper's top most part should go into the 1.5" area (between two of the teeth). If the chipper touches any tooth on the first outside blade then it will bind when you tighten the nut and will bend the chipper.

You are also right with the first two chippers being put on like a cross or plus sign, the third chipper if used would go half way between the other two chippers. Purpose here being balance, remember when that assembly begins to spin and all parts are not balanced you gonna have a wild vibration so they would look like this * look at your keyboard at the 8 key and symbol on your keyboard.

Last thing is the last blade with carbide teeth goes on and turn it so chipper next to it is located in the 1.5" between just like the first blade.

Put washer (if used, my set states to not use the washers) on then nut, finger tighten double checking all the blades teeth chippers to made sure they have not moved before putting wrench on it.

That's it:

Gullet: when talking about the regular looking saw blade the gullet is the area just in front of each tooth. That cut away area and it's purpose is to collect sawdust while the tooth is inside the piece of wood. The sawdust gotta have a place to go ya know!

Keep in mind you have three goals to accomplish here:

1. Put blades and chipper on so teeth are pointing correct way.

2. Make sure all chippers are NOT touching any teeth on two outside blades.

3. Keep it all balanced by spacing each chipper equally around the circle.

Don

Re: Confusion stacking up with new dado blade

#5

Re: Balance??

Larry Clinton

>Don I agree with all your statements except your comment about the balance of the blades. It should make absolutely no difference where the chippers are located as to blade balance. The chipper is balanced - If only 1 chipper was installed on an arbor, it wouldn't work well (a two tooth cutting blade) but it would still be balanced. A second chipper could be added in any orientation as long as the cutting teeth didn't overlap (even if they did it would be balanced, but might bend the blades) and would still be balanced - still wouldn't work well - but balanced. IMHO the reason the chippers are to be placed at approximately 90 degrees is to even the cutting load and reduce vibration due to the "load and free wheeling" effect during the chipper(s) cut. I am never too anal about positioning of the chippers (except to insure the carbide teeth are in a clear area of the adjacent blades) when making a wide cut requiring multiple chippers and have never noticed any issues on my Unisaw or the material being cut.

Re: Confusion stacking up with new dado blade

#6

Re: One Last Point to ponder-

Ron Hildreth, Alta, Iowa

>This should be performed with all blades;

After making sure the arbor nut is tight, plug your saw back in, but before reinstalling the throat plate, stand off to one side, turn the saw on and off in rapid fire succession to check that your dado blade is true and not out of balance. I'm not able to turn the blade by hand fast enough to detect any wobble, and by turning the saw on & off fast, keeps the saw from powering all the way up, but fast enough to detect any major malfunction.

I found that the tolerance of the blades holes are so tight around the arbor on my saw that I can actually think everything is kosher, when in fact it's not. Talk about major wobble and vibration!

If anyone has a safer way of checking blade installation, I'm all ears!

Ron in Iowa

Re: Confusion stacking up with new dado blade

#7

Re: Balance??

Don Evans

>Larry:

Yes, my wording doesn't really harm anything does it?

However, I failed to explain well enough what I was thinking.

Balance in this case is equal cutting around the circle motion of the dado. In other words all the chippers when used become a unit, this unit if allowed to cut at the same instance could cause stalling on a saw that is power poor.

Suppose one were to install 3 chippers each aligned with their teeth

side by side like this - instead of spacing them equally around the circle. This could on some saws cause the saw to begin a stall when they cut, then speed up while all of them are out of the wood, etc etc. Not likely to happen on my 3hp unisaw but very possible on my former direct drive crapsman.

I really didn't want to get into that in that message as I felt it may take away from the important parts of the message and become more confusing.

I didn't mean balance as in balancing a tire on a car but as I read it again it sure sounds that way.

Thanks for giving me the chance to defend myself and not answer before my second coffee. :)

Don

Re: Confusion stacking up with new dado blade

#8

Re: One Last Point to ponder-

Don Evans

>Ron:

The safer way (only one I can come up with) is to:

1. leave saw unplugged

2. use a dial indicator

3. turn by hand

4. note any runout and correct if excessive

Only problem here is you'll have to learn what is excessive, I don't know

Don

Re: Confusion stacking up with new dado blade

#9

Re: Confusion stacking up with new dado blade

Scott Whiting - Glendale, AZ

>Everybody gave you enough info to use the set. Nobody defined gullet which you had a question mark next to. The gullet is the open air space in front of each tooth. That is where chips are stored while the tooth is in the cut and then expelled from when that tooth leaves the cut. The definition is held over from steel saw blades. When sharpening steel blades the gullet is also cleaned out, or gummed, about the same amount with the grinding wheel as the top of the tooth is ground.

Scott

Re: Confusion stacking up with new dado blade

#10

Re: Confusion stacking up with new dado blade

Barry Irby

>Dan, I think we have hammered this pretty much to death and by now you "get". The idea is to install the chippers so that they nest closely to the side of the blade and do not bend the teeth or the blade or chipper.

Not to complicate things further, buy I have wondered if stacking the chippers in a spiral would not POSSIBLY be a mistake. I do like to spread them out far enough that only one is in the wood at a time, to reduce the loading on the shaft and the motor, but I am wondering if you spiralled them if the first one would not "Push" the shaft back and away, just slightly. If the second one came right behind it and it was further out from the bearings it would have slightly more leverage and twist the shaft even further. And so one with the third and fourth one. So, one big stacks with multiple chippers I try to put them in random order rather than in a spiral. Not sure it matters at all but I can imagine it might introduce wobble and vibration and cause the dado to be a few thousandths wider. There is a lathe that requires the drive pulley to be way out Ont he end of the shaft. Some of them have suffered broken motor shafts from the flexing it induced. I actually don't think the dado stack will induce much asymmetrical stress in the saw shaft, but the stack is heavy and does stress the shaft more than a blade. I'm just speculating.

Re: Confusion stacking up with new dado blade

#11

Re: Confusion stacking up with new dado blade

Dan Mitchell

>Thanks for all the great replies. I do see how it goes now & I understand the term "gullet". Very, very helpful!

Still gotta wonder why Freud didn't include a couple pictures.

Dan