Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Unisaw Startup Jolt

Posts

Unisaw Startup Jolt

#1

Unisaw Startup Jolt

Tim Jones

>I recently got a 36-R31x, the 3 horse single phase Unisaw, but was disappointed to see it jolt on startup. The jolt is not drastic, but it definitely will knock over a nickle on edge. You can plainly see the table jiggle a bit. It is smooth after is is up to speed.

I adjusted the belts, took the play out of the elevating shaft via the rear collar, but there is still significant play in the worm gear to rack elevation- I can wiggle the motor about 3/16th, and this movement (all in the worm/rack elevation gears) cannot be eliminated. If I wedge a board between the motor and cabinet to eliminate this slop, the saw starts up very smoothly, so it definitely is this elevation play causing the startup vibration, not a loose arbor or the belts. I spoke with a delta tech who said the that newer high torque motors cause this and it is a normal condition.

Do all recent unisaws have this startup jolt?????

Re: Unisaw Startup Jolt

#2

Re: Unisaw Startup Jolt

dwr

>Tim,

My X3 used to start like a dream and now it jolts big time. I went through the same processes you did with no success.

Here is something weird: I did find that, depending on how I pressed the start button, had an effect on how smooth it started. If I pressed it in quickly all the way, it really jerks... if I pressed it in slowly is started smoothly... I wonder if these "new high torque" motors are sensitive to how electricity is delivered... maybe a start capacitor issue?

Who knows... but it is obvious that Delta doesn't care much... if I had it to do over, I would buy a Powermatic.

Re: Unisaw Startup Jolt

#3

Re: Unisaw Startup Jolt

Tim Jones

>You might double check the collar on the rear of the elevating shaft, as that could drift away from being tight against the rear arbor if the collar's set screw isn't tight. That would explain yours getting worse over time. I removed a little play from mine and it did help a bit.

Re: Unisaw Startup Jolt

#4

Re: Unisaw Startup Jolt

Dan Mitchell

>I had a Unisaw briefly about 7 years ago. Didn't use it much for woodworking, though it came in handy for carpentry as I remodeled the house we lived in at the time to move to our present location a couple years back. Sold the Unisaw along with a 6" Delta "professional" jointer on ebay before moving, getting very good prices. A couple weeks ago, I got a Powermatic PM2000. I was only considering the PM & the Sawstop, and since the PM was 10% off and doesn't require a mobile base (built in casters) it wasn't that much more than the Unisaw. My Unisaw definitely had a clunk on startup, there was talk about it on this group then as well. The PM very smooth, just tried the nickel thing, it passed.

Another reason I avoided Delta is the jointer I mentioned had a warped fence, also a well known problem at the time. I complained & they sent me a new fence, just as warped as the 1st. Apparently now as then, customer satisfaction isn't high on Delta's list of priorities. I don't have an answer for you guys, but I can tell you when I sold my Delta gear on ebay I got very nearly what I had paid for it.

Dan

Re: Unisaw Startup Jolt

#5

Re: Unisaw Startup Jolt

Ken Oakley-Sunny St. Cloud, Fla.

>I have worked on Unisaws since the 1950's and don't remember any that didn't have that sudden jolt at startup. The one I have now, I bought 10 years ago and has done it since the gitgo.

Re: Unisaw Startup Jolt

#6

Re: Unisaw Startup Jolt

Bob Lemon - Sacramento CA

>Try putting a jumper across the start capacitor (the round black one), then start it. If that gives you a nice smooth start, then you have solved the problem. If you need more starting torque, go to a smaller capacitor with the same voltage rating.

Bob

Re: Unisaw Startup Jolt

#7

Re: Unisaw Startup Jolt

R. Lance in GR, Michigan

>Bought my Unisaw about 20 years ago...and have noted this jolt upon start phenomenon...also have noted that I've read various threads over the years regarding this issue...seems like it happens when the saw has been dormate for awhile and happens less when I've been working with it regular...suggest you put your nickel back in your pocket and get on with making things...if my saw gives me similar service in the next 20 years I'll know I bought a real good product...not perfect...but guess what, that Powematic 2000 isn't perfect either.

Re: Unisaw Startup Jolt

#8

Re: Unisaw Startup Jolt

Dan Mitchell

>"...but guess what, that Powematic 2000 isn't perfect either."

YOU TAKE THAT BACK! ;-)

Actually, I find the built in casters are kind of a PITA. Hard to deploy, & they don't support the legs on the extension table. The mobile base I had with my Unisaw was a lot easier to use. If I had to move the saw with each use as I did when I had the Uni, I'd really grow to hate the casters.

Dan

Re: Unisaw Startup Jolt

#9

Re: Dissapointed - WHY??

Larry Clinton

>I honestly don't know if my Unisaw "jolts" on startup (or my MiniMax MM 16, Grizzly 3hp dust collector, 2 hp Jointer, or Yorkcraft 20" planer). Unless the "jolt" is shortening the life of my equipment, it is a non-issue. The big V8 engine kind of rocks my van when starting too, - not going to worry any about that either. If it doesn't affect the machine performance - (your not feeding material into the saw at startup are you?) and doesn't hurt the equipment - what is the problem?

Re: Unisaw Startup Jolt

#10

BINGO!

Grant in Iowa

>Few users know that you can vary the size of of start capacitors. You need one large enough to start the saw with the largest dado set installed on your AC power feed, but not large enough to cause the bang on startup. Take the info from your motor and maybe uninstall the start capacitors and head off to the local motor repair shop. Describe your problem and appeal to them for a smaller capacitor set.

By the way, the start capacitors are under the humps on the motor most times.

FWIW,

Grant in Iowa

Re: Unisaw Startup Jolt

#11

Re: BINGO!

slashdev

>So, these capacitors don't retain a charge after the saw is turned off? Jumpering across the cap won't give the operator a charge? :)

Re: Unisaw Startup Jolt

#12

Re: Dissapointed - WHY??

Tim Jones

>Having just pulled the trigger on what for me is a major tool purchase, I want to be certain there are no issues with my saw and it behaves just like a unisaw ought to. With any production run there will always be a percentage that shouldn't leave the factory, and Delta ought to have a very low percentage. If only 2% of their production run jolted on startup, I would have an issue with Delta and look for a resolution. It could have been the symptom of a faulty or cracked casting or who knows what. I could find no local distributor that would power up their floor models for me to compare mine to, and the only other unisaw I can access is over 20 years old with the baldor motor, not the weg that I have. I couldn't find anyone (other than the Delta tech and salesman who both had a vested interest in not having a unit returned) to tell me that 'Yes, it jolts a little, and that is normal'. I wanted to hear the truth from unbiased folks that have used this saw.

My research done on the web, phone calls to Delta, and in person indicates that all unisaws will jolt on startup and it doesn't seem to be an issue.

The main point is how it cuts a piece of wood, and that was never in doubt as it is rock solid, has a fearsome amount of power, and it is built like a tank. Now I can go back to my shop and reapply some more wax to the top, wipe off some drool, and maybe even run a few boards through it...

Re: Unisaw Startup Jolt

#13

Re: BINGO!

JohnKJordan in East TN

>>So, these capacitors don't retain a charge after the saw is turned

>off? Jumpering across the cap won't give the operator a charge? :)

Large capacitors can certainly hold a charge. You can actually spot weld with a bank of charged capacitors. The picture tube in a TV set is in effect a big capacitor that can hold a charge strong enough to give you a very serious high-voltage jolt. However, that used with a motor is relatively small and the voltage (DC, btw) is fairly low.

The act of jumpering across the terminals will discharge it immediately. You can use a screwdriver with a plastic handle to short across the terminals - you may get a spark and a pop if the capacitor is charged.

The device should be unplugged or disconnected from the mains, of course, before opening or touching anything inside.

JKJ

Re: Unisaw Startup Jolt

#14

Re: I understand Tim

Larry Clinton

>I didn't realize you were not aware of this characteristic of the Unisaw. Sorry if I came on to sharp. I have the left tilt that I purchased about 4 years ago, it has the cast extensions (both sides), Formica covered extension table, Delta mobile base, and 52" commercial Besi fence. I have a WW2 blade installed. It has been a terrific saw for me. Never once regretted buying it.

Re: Unisaw Startup Jolt

#15

Physics 2

Tony - Memphis

>In my physics 2 class, the instructor brought in a couple of very large caps and dropped a thin piece of wire across the terminals....made quite a loud bang and flash as the metal vaporized! Pretty cool. Same guy would run two long coax cables down the hall and run opposing current through them so the two would move away from each other due to the magnetic fields. Neat class and great instructor.

Tony

Re: Unisaw Startup Jolt

#16

Congradulations Tim......you've bought

R. Lance in GR, Michigan

>a great saw....take good care of it and your grandson will be making projects with it with his kids....I've been thinking about this and it seems every tool I own has some issue/quirk ....and every tool I own has been either updated, improved, dropped from production, or sold at a better price point....sometimes right after I make the buy....I guess all you can really do is make an intelligent choice of a good tool (which you did)....work with its quirks and keep on keepin on.

Re: Unisaw Startup Jolt

#17

Ha!

Tony - Memphis

>My Delta Contractor's saw (34-444) does all sort of rockin and rollin before it calms down after startup! We're only talking a half a second or second or two of transient behavior. That's one difference between the saws I guess. I'll graduate to a cabinet saw someday maybe.

Tony

Re: Unisaw Startup Jolt

#18

No jolt for me............

HC Sakman

>Hi Tim,

My 3 horse single phase Unisaw never jolted. It had Baldor motor with 3 huge capacitors, early 80's model. Also it was stopping within 10 seconds. When I position a workpiece on a mitergauge and holding it with one hand, while turning the saw on, I want no jolting , banging. I know a few guys with new or newer saws (2 Unisaw, one General 350), having the same complaints. Probably they're gonna say what I hate to hear: "These models just do that, normal."

Chico...

Re: Unisaw Startup Jolt

#19

Ditto...... the Big Band Theory

Mark Goodall - ATL - tooljunkie

>My Unisaw never had that Bang.

Back in 1997 (I think), after waiting almost 20 years of wanting to own a Unisaw, I was finally at a point in life where I could..... and right at that time there was this big "BANG AT STARTUP" problem with Unisaws. I remember talking to Jim Cumming at American Woodworker Magazine about it when that magazine was in it's infancy.

Seemed to be that for about a year, there was a large percentage of people buying new Unisaws that were having this loud "BANG" when their new Unisaw started up.

There were many theories running around at the time. The internet was fairly new at that point and there was lots of information and mis-information about this "problem". For the life of me, and can't recall what exact cause and solution was. There were many theories. I do remember that I purposely found a place that had a fwe of last years model in stock so I bought one from there. I never had the problem but knew many who did.

This was also a year or two before the other big "fiasco" at Delta. There new 6" jointer with closed base (for years their earlier 6" model was an open stand) that had a warped fence problem.

Careful planning at the time of purchasing also helped me avoid that problem, but I knew many people who were affected by it.

I'll have to go through my old notes to see if I can remember what the solution to the Unisaw's big bang was. There was a solution, beacuse it was only about a year or so that the Unisaws were having that problem from the factory.

Happy Woodworking!

Re: Unisaw Startup Jolt

#20

Re: Unisaw Startup Jolt - What Delta Support says *LINK*

Glenn Stasse

>This can occur because of the high starting torque produced by the current motors.

The motor is a 3 hp, single phase, induction motor, designed to operate on alternating current (AC). It is very efficient which means it is smaller (and lighter) and draws less current than older 3 hp motors. Alternating current, when plotted graphically, forms a sine wave. This sine wave repeats itself 60 time each second. Depending on where the sine wave is in its cycle when the start button is pushed, the "bang" can occur.

Loosening the belts slightly will help absorb some of the shock at start up (belts should deflect approx �" under finger pressure) . Also ensure that both Pulleys are secured onto their shafts tightly. Assure there is no excessive end-play in the raising and lowering mechanism (follow directions in the Instruction Manual to adjust.


http://support.dewalt.com/cgi-bin/dewalt.cfg/php/enduser/std_adp.php?p_faqid=3138&p_created=1172756978&p_sid=OXWyogQi&p_accessibility=0&p_redirect=&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9NzAmcF9wcm9kcz0xMzkyJnBfY2F0cz0wJn

Re: Unisaw Startup Jolt

#21

Re: Ditto...... the Big Band Theory

geary from nj

>THinking about buying a Grizzly 12",Extreme series,cabinet saw,....any pros and cons that need to be said before I take the plunge? geary from nj