Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Subfloor question

Posts

Subfloor question

#1

Subfloor question

Nat Robison

>I'm finishing a basement and have a question regarding a small amount of subfloor where it meets the stairs.

The last step onto the concrete floor is 1.5" higher than the risers on the rest of the stairs. I've grown accustomed to it over the years but several others have noticed it. I'd like to close the gap and basically create a small landing at the bottom of the stairs.

I was thinking of affixing either 1.5" of plywood or 2x lumber to the floor and carpeting over it. The whole basement and the stairs are going to be carpeted. Any suggestions on finished floor for this landing? I was thinking carpet as well but it would create a lip to trip on since the concrete floor will be 1.5" lower than this small landing.

Any thoughts on a better way to do this and/or finishing ideas for the small landing?

Re: Subfloor question

#2

Re: Subfloor question

Pete in Holland, MI

>Either way, it will be non-standard and a trip hazard to those not familliar with it.

If you're not too far into the project, pull the stairs out and make new ones with the right rise to the number of steps. Could also just remove the treads, and start progressively cutting down the stair stringer so each step is progressively lower, thus making up the 1 1/2". Could also remove the treads, and start progressively dado the mating surface of the treads to lower each progressive tread height. Would require some cleats to redistribute the forces onto the original thickness of the tread.

Any wood product attached to a concrete floor has the opportunity to warp with the slightest amount of moisture.

Either way, you have some work cut out for you, but in the long run, it will be worth it.

Re: Subfloor question

#3

Re: Subfloor question

R. Lance in GR, Michigan

>Nate....I think that you have a good idea to create a little landing there as this difference may in itself result in someone tripping as they may get accustomed to the regular rise of your stairs and that added 1.5" of rise could throw a person off. I'd suggest that you make this "landing" larger than a regular step in its surface area and that you finish it to contrast with the basement floor so people will be more aware of it as they use the stairs. I know it would be a real headache, but if those stairs are a couple of stringers and some treads could you reframe it ????

Re: Subfloor question

#4

Re: Subfloor question

Mark Mandell - Gone Round In Jersey

>Nat,

When I put in my basement office, I put down 1/2" homasote and then lined the floor at the wall with 2" PT ply strips glued and shot into the concrete. The homasote kept any moisture away from the padding and carpet, and the ply allowed tack-strip installation. You could easily do likewise with 3/4 material or even double the homasote to a full inch which will largely negate your one-high riser.

If you really want to go whole hog, you can build the floor up to the "proper" level for about 6 feet in all directions to the step. Glue down the homasote board to the full make-up height by 2 panels' worth out from the step, then feather it out with a belt sander (hooked up to a shop vac!!), and carpet over that "ramp." People will barely perceive they're walking "up-hill" and you'll have no ledge to trip over.

mm

Re: Subfloor question

#5

Re: Subfloor question

Steve Schoene

>Unless you have a really, really dry basement I'd wonder if carpeting directly over the concrete is a good idea. I'd want to put the carpet for the entire basement over 1x pressure treated sleepers with vapor barrier supporting 3/4" plywood or Advantech sub-floor. That would take care of both the odd riser, and the possibility of a musty carpet.