Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

DC/ heat loss questions?

Posts

DC/ heat loss questions?

#1

DC/ heat loss questions?

Barry Irby

>Am I doing this right? My math and science skills are a little rusty.

There have been numerous posts on having the DC exhaust outside verdu inside. Mine is outside and I like it, but got to thinking about the heat loss/gain.

Looked up the Specific Weight of Air. It varies with temperature and other things, but at about 70 degrees (F) it weighs about .075 lbs per cubic foot.

So if I run my DC for five minutes and it is pulling 500 CFM, that's 2500 CF times .075 or 187.5 pounds of air. (I tend to run my DC in short bursts.) I am having trouble here, hard to visualize almost 200 pounds of air.

I looked up the Specific Heat of Air and It's about .25 BTU's per pound per degree F. (Sort of hard to find that number, apparently the rest of the world uses the SI system, Who knew?)

So, if the makeup air from outside is 15 degrees different that the shop air, 187.5 times .25 times 15 is about 703 BTU's.

There are a lot of variables here. Moisture vapor affects all of this, etc. Also, if the temp. out side is less than 15 degrees different that would affect as it would if it were more. I have a 1300 CFM DC, but I used 500 CFM as a Stab at the volume because I usually have one blast gate open on a four inch port at a time.

Just struck me as a lot that five minutes of DC could pull out (or in) 700 BTUs. I have a little window AC in my shop that produces about 8000 BTUH. If I were to run the DC for an hour it would pull 12 times 700 or 8400 BTUs. HMMM? Does this SWAG seem reasonable?

Re: DC/ heat loss questions?

#2

Re: DC/ heat loss questions?

Al Stokka - Cambridge, Iowa

>Barry,

Yes.

I thought everyone knew.

Yes.

You're welcome,

Al

Re: DC/ heat loss questions?

#3

Re: DC/ heat loss questions?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Barry,

They were interesting questions, and I never considered that air weighed something. Now I wonder if the weight of the dust should be added to the volume of air over time to arrive at the correct air weight. :<)

George

Re: DC/ heat loss questions?

#4

Jesper, Denmark

Re: DC/ heat loss questions?

Jesper, Denmark

>Barry,

You have the data right.

Re: DC/ heat loss questions?

#5

Re: DC/ heat loss questions?

Randy D

>Your dust collector will be exhausting almost twice the output of you window unit....comparing cfm ratings.Heat /humdity difference of outside vs conditioned air will quickly overpower the unit at just 4 degree delta T and 50% RH. This will also depend on the size of the shop. I'd try and bring the exhausted air back into the conditioned space if at all possible.

Re: DC/ heat loss questions?

#6

Re: DC/ heat loss questions?

Barry Irby

>Randy, You are right. If I ran the DC in long bursts it would overwhelm the little window unit.

I thought this was an interesting bit of mathematics. Its been a long time since I took any HVAC classes (over 35 years). I was worse than rusty on the math and concepts.

Not only did I not consider the humidity, I did not consider the make up air either. The number of variables are astounding. If I leave he door between the house and shop open, the DC sucks air down out of the house. If the door is closed, It sucks air in through the cat door. In that case, the calculations are way off. The air comes in through the cat door, goes through the machine and back out. At least Ont he machines near the cat door. So It does not take out as much AS as the numbers might indicate.

I am pretty happy with the DC being outside. All the dust, including the microfine stuff is outside. The crud that falls out from changing the bag is outside. The noise is outside. So far, my experience is that the heat loss/heat gain are worth it.