Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Gasoline/Chainsaw question (OT?)

Posts

Gasoline/Chainsaw question (OT?)

#1

Gasoline/Chainsaw question (OT?)

Barry Irby

>Somebody posted the other day saying higher octane gasoline would not age as quickly as the low octane stuff.

What do we know about gas? Is that true?

And, is there any reason to not buy the higher octane stuff, other than cost? For the little bit of gas I use in my various things like chainsaw and lawn mower the cost would be insignificant. Does the higher octane gas benefit the engines? Is there any way it can damage the engines if they only call for the low octane stuff.

Re: Gasoline/Chainsaw question (OT?)

#2

Re: Gasoline/Chainsaw question (OT?)

Ray, SW Ohio

>The only difference is the amount of hydrocarbons added to the fuel. Higher octane only burns slower. My 2�.

Re: Gasoline/Chainsaw question (OT?)

#3

Jason Roehl in Lafayette, IN

This may help a bit.... *LINK*

Jason Roehl in Lafayette, IN

>I know most folks don't care much for Wikipedia, but the info in this article jives with what I've read elsewhere (some VERY technical sites about gasoline).

Gasoline is a mixture of hydrocarbons. Additives may or may not be. Octane rating has nothing to do with the amount of energy in a gallon of gas, but provides resistance against knocking (pre-ignition). I suppose that a higher octane fuel, depending on how that is accomplished, may have some additives/cleaners/stabilizers that prevent "varnish" in small engines that are left to sit for long periods of time. Personally, I'm not Mr. Maintenance on my various gas-powered yard tools and rarely have an issue with them starting when I need them to.

Jason


Octane Article at Wikipedia

Re: Gasoline/Chainsaw question (OT?)

#4

Re: Gasoline/Chainsaw question (OT?)

Larry Clinton At Frankfort (Central)., Indiana

>As Jason has said, Higher octane is used to prevent "pre-ignition" which causes spark knock in high compression engines that are timed to fire just before the piston reaches top dead center. I certainly am no chemist, but I personally do not believe the gasoline would have properties that could help in storage. I purchase and use "Stabil" which is an additive which extends the storage life of gasoline. Before I started using it I have had gas stored over the winter which had a foul smell. I also had mower engines that accumulated "varnish" in the fuel system. Since I started using Stabil, I have not had either of these issues. As I am very lax in prepping my mower, weed eater, Generator, chain saws etc. for winter, I started adding Stabil to ALL gasoline I buy for the small engines when I fill the containers. I do this even with the fuel I mix for the 2 cycle engines. This may cost me a few cents, but I know all the fuel in the engines contain the additive. I never drain or worry about the fuel. I pulled out the mower this spring and it started first pull.

Re: Gasoline/Chainsaw question (OT?)

#5

Re: Gasoline/Chainsaw question (OT?)

David Sparks

>I don't know the answer to you question, but I cut a lot of wood this Spring. I did quite a bit of research into various aspects of lumberjacking. I learned two things: 1. Fresh gas is best and 2. Keep your gas in a metal container. A professional lumberjack claimed that plastic containers will break down and gum up your chainsaw's carburetor. I don't know if that is true. I bought a little funnel made for Coleman gas lanterns that I use to filter the fuel as I pour it into the saw. The funnel has a very fine brass screen in it to catch any impurities. The jets in a chainsaw's carburetor are very tiny and easily clogged.

Re: Gasoline/Chainsaw question (OT?)

#6

Re: Gasoline/Chainsaw question (OT?)

Rob Stokes in North Vancouver

>Larry's answer is the best one. 2-stroke engines typically don't need anything above 87 octane. Consumer equipment is built to run on readily available fuel, and that's what's readily available. Depending on the 2-stroke, you can actually damage an engine by running a higher octane (this is mostly attributed to marine engines though).

Use 87 Octane - it's all you need.

More important is your choice of mixing oil. Don't cheap out on it - get decent brand name 2-stroke oil and mix it to the manufactures specs. Don't get marine oil though (TC-W3) - it's designed to support a higher compression 2-stroke that typically runs cooler than air cooled engines at sustained high RPM's. Most oils these days support 50:1 as they have better lubricity than the oils of old. Older oils demanded 32:1, or sometimes ratios that were higher. Not any more. And contrary to popular opinion - more oil is not better. Upping the ratio of oil/gas arbitrarily can cause an oil film to build on the steel components inside the engine. This in turn can reduce heat transfer which can end up causing more damage. If your saw's designed to run at 50:1 - run it at 50:1. If you've got your own tar field on your muffler - check your math when you mix.

Larry's concept of adding an aftermarket fuel stabilizer to the gas cans he uses to support his small engines is by far the best practice. Make it a habit and it will become one. Once done, you never have to worry about "bad gas" again. I also do this with my boat gas - it's FAR cheaper in the long run.

The advice you got on not using plastic tanks is bunk. The polymers won't degrade. Think about it - if that happened, eventually the tanks would start to leak from the inside out. I've never seen that happen. And if the plastic tanks did act as you've been told, there's no way the material would be approved for use by the USCG in marine fuel tanks - which it is. So feel free to use plastic tanks - it makes no difference. In fact - I prefer plastic tanks. Water in the fuel is a fact of life - maybe you got it form the gas station - maybe you left the lid off the gerry can when it was raining out. Regardless, water happens. I'd rather have a tank that's impervious to water than a tank that will rust. You won't find a steel tank at my place, and I've got tanks for boats and lawn mowers and chainsaws and and and....

Oh - it's a good idea to use a filter, but chainsaw carbs do not "clog up easily". In fact, they're quite forgiving and the tolerances on a small carb like that are WAY bigger than a carb used on a car. Car's have their fuel economy measured by governing bodies so there's incentive to make a fine-tuned carburetor. Chain saws need to run when you need them and no one cares about their gas mileage. As such - they're designed for dependability, not efficiency. Dependability in a chainsaw means letting the odd piece of sawdust pass without incident.

Hope that helps.

Rob

Re: Gasoline/Chainsaw question (OT?)

#7

Don't waste money on higher octane.

Tim Greif - West of Chicago

>You've gotten consistent advice about the octane rating. It has nothing to do with energy content. It simply controls the burn rate. Higher octane gas burns slower and had less tendency to detonate (ping) due to an uncontrolled burn.

I believe that higher octane gas would go bad quicker, owing to the fact that it's a lower demand fuel and hence, doesn't "turn over" as fast in the dealers tanks as the quick selling 87 octane. So it's probably older when you put it in the can than a similar lower octane fuel.

Buy the 87 and use Sta-Bil. Put gas older than two months in your car and refill the can.

Re: Gasoline/Chainsaw question (OT?)

#8

Re: Gasoline/Chainsaw question (OT?)

Kit Gage in VT

>I will have to be the dissenter here. Having spent a lot of time at ArboristSite.com and doing a fair amount of milling myself with a chainsaw, I recommend a higher octane rating then 87. The saw sems to run cooler AND I only use synthetic 2-cycle oil. Both of these (octane & oil) are encouraged by the several techs that frequent the site. We are using these saws harder then most homeowners but what's good for the goose.....

Re: Gasoline/Chainsaw question (OT?)

#9

Thanks Everybody

Barry Irby

>

Re: Gasoline/Chainsaw question (OT?)

#10

stabilizers

JKJ in East TN

>I also use Stabil, which came recommended by trusted sources.

Some of my engines that don't get started much, such as the log splitter or a small semi-trash water pump, seem to start much easier after some neglect than before using Stabil.

JKJ