Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Grr-Ripper Questions

Posts

Grr-Ripper Questions

#1

Grr-Ripper Questions

Barry Irby

>I have looked at the Grr-Rippers once or twice. I have to admit, the $50 price stopped me, and they looked pretty complicated. My question is, do they require a lot of fiddling and set up? Do you change them around for various jobs? Often? Or do you just pick them up and use them?

Looks like I will be buying or making more push sticks. I got a warning. I am in the habit of clamping my hand to the fence and using my thumb and forefinger to slide the work through. I changed the fence and that might have changed the angles or maybe it was just time for a warning, but last night I kicked my thumb. I was very lucky (yes and Stupid). It was less than a paper cut and at first I did not think it would bleed, but it was a cut. Perfectly in one of the little creases on the back of my thumb. Time for some push blocks and sticks and time to use them.

Re: Grr-Ripper Questions

#2

Re: Grr-Ripper Questions

George (Oxford, NC)

>Depending on how you use them, they will take some little set-up each time you use them. I only use mine for short and/or narrow cuts so the total shop time used to set it up is not really a problem. I use regular push sticks for most of my cuts, but I do feel really safe using the Gripper for those short/narrow cuts. Worth it in my book.

George

Re: Grr-Ripper Questions

#3

Re: Grr-Ripper Questions

matt overton

>Barry,

All of us that use our hands and don't practice safety ALL the time are all on borrowed time. I just ordered my GRRRipper yesterday (along with a splitter). Rockler has them on sale for $39. Still alot, but think of the alternative. Look around your shop, how many $40 items do you have that may not have been a good investment? Thank God you still have a thumb.

Re: Grr-Ripper Questions

#4

Re: Grr-Ripper Questions

Paul Woolson

>I use mine for every pass through the table saw. And that is literally every day. There's very little to set up. I sometime have to move one of the legs so that it will clear the blade, but that's loosening two thumb screws and moving the leg, then re tightening them. 10 seconds tops. I only use the extra "foot", that holds it level, when I'm working with a very small piece.

In my opinion, it's the best $50 I ever spent in the shop.

Re: Grr-Ripper Questions

#5

Re: Grr-Ripper Questions

Dan Manturi

>Table saw use does require some adjustments. My education on the need for more saftey came when I knicked the tip of a thumb on a jointer. I was lucky and it just caught the flesh at the very tip and sheared it right off. I cannot even remember how it happened. I did not touch that tool again for a while, but when I did, I used the Grr-Ripper instead of the cheesy factory push handles. Solid, good grip. In fact, I am arranging to get a second one now that I am upgrading to an 8" jointer. More opportunity for injury with bigger toys, but we work with dangerous machines in this hobby. Even a router can do a lot of permanenet damage. What I need to do is get into the HABIT of using the GrrRipper and other saftey items whenever possible.

I'd like to quit woodworking at an old age with all my fingers intact. It is a solid device and is worth the money.

Dan M.

Re: Grr-Ripper Questions

#6

Re:

Binen

>I bought the Grr-Ripper over a year ago. Some of the best money I ever spent.

Binen

Re: Grr-Ripper Questions

#7

It's money well spent

Charles R. Smith from Victoria

>There was a thread on the GRR-Ripper a few days ago. All of the opinions given at that time are the same as these ones. The few seconds (literally, 10 to 15) it takes to set it up are nothing, and in most instances you don't need to do any adjusting -- just grab it and run, knowing that your fingers are protected. Best shop accessory I've ever bought, even if it seems a bit pricey.

Charles (who likes the fact he still has ten digits on his forelimbs)

Re: Grr-Ripper Questions

#8

Re: Grr-Ripper Questions

Jesse in New Mexico

>I agree with the others. Only setup is to loosen a couple of knobs, move the "foot" up or down to match thickness of your stock. Or you may need to do a similar adjustment to move the central grabber-thingy. Very intuitive once you put the pieces together the first time. I wouldn't be without it, for tablesaw and router.

Re: Grr-Ripper Questions

#9

ENUFF Said?

George@Colonel's Workshop-Havertown PA

>OUCH


img

Re: Grr-Ripper Questions

#10

Re: Grr-Ripper Questions

Larry Clinton At Frankfort (Central)., Indiana

>I have looked at the Grr-Rippers once or twice. I have to admit, the $50 price stopped me, and they looked pretty complicated.

My question is, do they require a lot of fiddling and set up?

Barry, I use my Rippers every time I rip a board on my Unisaw, sometimes on the router table and jointer. The Grr-Rippers are pretty easy & quick to set up. with boards 2" or more wide - normally you just orientate the ripper so the blade passes between the rails. (end for end orientation). Once in a while you have to adjust a rail by sliding it in the ripper. This is a 5 to 10 sec. operation (each). The only other issue is that you have to watch the blade height so you don't cut into the "bridge" of the Grr-Rippers. This you can't cut 1/4 thick and 2" thick with the same blade height. The demo tape or Cd (can't remember which I have) does make it look like you have to set up for just about every width. I guess you could, to have the Gripper rails right on each side of the saw blade. Does make it slightly safer as the off-cut is controlled clear through the cut and past the blade. But to be honest, I really don't do that. Basically the adjustments are to keep from cutting a slot in the rails. You check by running the ripper against the fence and past the blade (saw OFF) to see if the blade hits a rail. If it does, flip the ripper end for end and try it again. If it still hits, you have to slide a rail over or add a "side" rail to align the slots between the shoes with the blade. (Ain't rocket science) if you goof, it won't hurt the blade, but smells funny (melted plastic) and you now have an extra slot in a shoe. (I have a few - do need to get some new bottom rails).

Do you change them around for various jobs? Often? Or do you just pick them up and use them?

As above, you may have to slide or add a rail for various widths. Narrower pieces require the addition of the "shoe" to keep the ripper level and allow more control. This takes 30 sec to a min each to add and adjust. However you will find the time is saved many times over with the accuracy you get having the proper control. I can rip any length 1/4" to 4" wide strips safely and very accurately (guessing +/- .002" wide). By the way all the adjusting & attaching screws are fitted with knurled knobs, and are captive in the parts except the screws that hold the handle in position - I haven't moved the handle more than 2 - 3 times in 3 years, so tools aren't required for adjustment.

Looks like I will be buying or making more push sticks. I got a warning. I am in the habit of clamping my hand to the fence and using my thumb and forefinger to slide the work through. I changed the fence and that might have changed the angles or maybe it was just time for a warning, but last night I kicked my thumb. I was very lucky (yes and Stupid). It was less than a paper cut and at first I did not think it would bleed, but it was a cut. Perfectly in one of the little creases on the back of my thumb. Time for some push blocks and sticks and time to use them.

I highly recommend the Grr-Rippers. I have damaged mine over the last 3 (or more) years use thorough careless use or setup. I need to replace a few of the lower rails on my set of 2 of the (Deluxe) units. However if they were damaged beyond repair I would consider it money well spent and would buy a couple more.

Re: Grr-Ripper Questions

#11

Re: Grr-Ripper Questions

John Tenhundfeld

>Thanks for the tip about the sale at Rockler. I just orfered one. I like all 10 fingers.

Re: Grr-Ripper Questions

#12

Are you looking at the new or old model?

ALBERTABO

>I am interested in getting one or 2 of these and wonder if waiting for the new models just realeased is worth the hassel?

Bob

Re: Grr-Ripper Questions

#13

You use Bessey's?

Bri in Mtl

>For this part of your post? "I am in the habit of clamping my hand to the fence and...." Sorry, couldn't help it ;)

I got the Grripper after a bad kickback -well worth it even if it was $100...

Re: Grr-Ripper Questions

#14

Re: Are you looking at the new or old model?

Brian In Dawson Creek

>There�s a new model out???

Checked the web site but all I could find was the new bridge attachment. In any event I use the gripper when ever possible, setup is minimal to me and not an issue and well worth the money.

Brian

Re: Grr-Ripper Questions

#15

Re: Are you looking at the new or old model? *LINK*

Albertabob

>Hi Brian:

The website really needs some serious upgrading and seems lacking in information relative to what is being sold.

The demos are good.

At any rate this is apparently the new improved one and as I don't have the old unimproved one I don't know which one to buy.

Regards

Bob


new improved Grr ripper

Re: Grr-Ripper Questions

#16

Re: Are you looking at the new or old model?

Brian In Dawson Creek

>Nothing has changed at least that I can see � with one (the basic model) you get the basic gripper, with the advanced model you get the stabilizing plate and an adjustable spacer. Both models are the same except for the additional options on the advanced model. I have the advanced model and would recommend it; if you don�t used the extra features then you still have the basic model. I have found that I use all the features on the advanced model and well worth the cost.

Brian

Re: Grr-Ripper Questions

#17

Re: Are you looking at the new or old model?

albertabob

>Thanks Brian.

I was under the impression that they were different in design.

In that case I can get one at Lee Valley on Saturday.

Bob

Re: Grr-Ripper Questions

#18

Buy 2.

Joe Pack

>With 2, you can "hand over hand" with a longer board without losing control. And buy the set with the stabilizer. It makes a world of difference; the more surface in contact, the less "tippy" the Griper will be. More money, I know, but you are worth it.

Re: Grr-Ripper Questions

#19

Nice idea for Christmas gift list

MN deepwoods (Dave)

>Family members are usually willing to spring for 'safety' items aren't they? This is the first I've heard of this great gadget. I checked out the website and I'd certainly rather make room in my shop for something like this than for gloves or mittens that have fewer fingers, or shorter fingers, on them. Thanks for sharing this 'new' tool.

Dave

Re: Grr-Ripper Questions

#20

agree

Mike Schwing from Md.

>Probably the best $50 I ever spent in the shop, too. The Gripper is incredibly useful! Any setup time hassles (minimal to none) are outweighed by the safety and flexibility of the tool. I've been wanting a second one and the Rockler sale will do it for me. Can't believe something at Rockler is actually cheaper than anywhere else!! First time for everything.

Re: Grr-Ripper Questions

#21

Can this be used with splitter and blade guard?

Alan Tolchinsky

>I always use the above safety items so I was wondering if they're compatible with them? Thanks!

Re: Grr-Ripper Questions

#22

Re: Can this be used with splitter and blade guard

Larry Clinton At Frankfort (Central)., Indiana

>Alan, I have Microjig splitters installed in my Unisaw blade inserts. The Grr-Rippers work very well with these (made by the same company. The blade guard would not work well with the rippers, as they are meant to hold the piece being cut through and beyond the blade. I suppose you could use the grippers with the guard - but that would require you to have 2 grippers (which I do use) and you would have to remove the gripper from the board when you reach the guard as you couldn't pass the ripper under the guard. This would defeat the benefit of the Grr-Ripper's as you would then lack the ability to maintain downward pressure and keep the material against the fence as well. IMHO, I don't think the Grr-Rippers would be a good investment if you intend to keep the overhead guard in place. I personally don't feel the guard is helpful in protecting me when I have the control the Grr-Rippers give. This is only my opinion and I would not advise anyone to remove the guard if they think it is safer. I personally haven't seen many saws in use with the factory guard as they interfere with many operations.