Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

biscuit joiner

Posts

biscuit joiner

#1

biscuit joiner

Dan Collins

>Friends: I have a Porter Cable Plate Joiner (model 557). It has a small blade to cut "FF" biscuit holes. To change to the small blade, a retaining bolt needs to be removed using a 5/32 hex wrench. I have removed it and changed the blades several times before. This time, the bolt would not budge. I spray some WD-40 on it to see if it would free up. That didn't help and now I have twisted so hard on the bolt that it is stripped. I now need a new bolt, but more importantly, I need to remove the stripped one. The Porter Cable repair shop is 50 miles away and I don't think it is under warranty anymore, plus they take forever to fix any tool there. Any suggestions on how to get the bolt out of there? Any ideas as to why it would have become unmovable. I don't think it overheated at anytime, nor has it been exposed to water, although my basement shop is fairly humid. If I can fix this, I want to make sure it doesn't happen again. Thanks. Dan collins

Re: biscuit joiner

#2

Re: biscuit joiner

Barry Irby

>IIRC, when I changed mine I put the Allen wrench in the bolt and gave it a sharp tap with a hammer to give the effect of a little impact wrench.

Are you saying the hex socket stripped? What about an Easy Out? Or whatever that thing is Sears advertises for removing errant screws.

WD 40 may not be the right thing for this. My choice is PB Blast which can be had at an Auto Parts place.

Do you have an impact driver. (Screw Driver like a drill). That might work with the Easy out. If you don't have one, you should. Go buy one, a new tool always makes me feel better.

Re: biscuit joiner

#3

Re: biscuit joiner

Edward inVancouver

>Last resort for any stripped screw head is to dremel a slot in the head of the screw/bolt and use a flat blade screw driver to get it out....

Re: biscuit joiner

#4

Re: Last resort

Kneale Brownson in sunny N. MI

>Last resort after the slot breaks off is dremel the head off the screw so you can remove whatever it holds and leave you with a fastener stem. Then apply some heat and twist the stem with a Visegrip as tight as you can make it.

BTW, WD40 is about the worst performing penetrating fluid on the market. PB Blaster and Kroil are some of the most effective. An alternative is some Automatic Transmission Fluid mixed with some Acetone. Works better than any of the marketed products.

When dealing with socket head screws it's a good idea to clean out the head with solvent and a pick and tap the driver into it firmly. This is one place I find WD40 to be worth using as a cleaner. I soak and then blast with air before scraping the corners with a pick.

Re: biscuit joiner

#5

Re: biscuit joiner

Derek

>Please don't take this wrong, but I done this several times -

Are you sure you are turning it in the correct direction? It is likely a reverse thread screw.

Re: biscuit joiner

#6

Re: biscuit joiner

Lee Ohmart

>I have a PC biscuit joiner and have also noticed that getting that danged screw out took quite a bit of effort. After I lightly lubed the threads with a light oil, it seemed to improve some. I'm always paranoid about stripping out those hex-key systems although my experience is that it is the key that strips on the larger sizes. With smaller keys it seems to be the female part that fails. In gunsmithing, the advice is to keep an eye on the hex-key and screw and if it looks like either is getting worn, replace it. The other thing is to use more precisely made tools. People screw up a lot of valuable guns by using poorly fitting tools. I wish the people at PC would switch to a Torx or square drive system.