Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

OT keep latex painted parts from sticking together

Posts

OT keep latex painted parts from sticking together

#1

OT keep latex painted parts from sticking together

Bill Hammond, Oregon Coast

>I am in the middle of a project that, because of poor planning on my part, has left me with about 25 pieces; shelves, doors and sides that have been prepainted with acrylic latex paint. I now need to stack them to make room to finish the project.

Has anyone found something that can be used to separate pieces that the paint won't stick to and then peal the paint off of the wood parts? something I hope that is not too esoteric and unobtainable here in the hinterlands.

All ideas greatfuly welcomed

Bill

Re: OT keep latex painted parts from sticking together

#2

Dale Lenz

Re: OT keep latex painted parts from sticking toge

Dale Lenz

>Might try laying wax paper between the pieces.

Re: OT keep latex painted parts from sticking together

#3

Re: OT keep latex painted parts from sticking toge

Al Stokka - Cambridge, Iowa

>Bill,

Be aware that I haven't tried it but, I seem to recall that talc (think baby or bath powder) can be used for that purpose. Perhaps my mentioning it will jog someone's (a someone who has tried it) memory.

Al

Re: OT keep latex painted parts from sticking together

#4

something else to consider

Bill Tindall, E.TN

>while the wax paper may, and probably will, keep the parts from sticking together it will also keep them for curing. Latex paint is composed of balls of polymer (the latex) swollen with some solvent (yes, water based paint has lots of solvent. that is why it stinks after painting) suspended in water. After application, the water evaporates and the solvent-soggy latex balls coalesce into a film. For the film to become hard the slow evaporating solvent must evaporate, and that takes a while. If these parts are all stacked with no air circulation the paint film is going to stay soft for some longer time than paint on a wall. The paint on my trailer wood (ext. acrylic) was soft for days with good circulation back in the cooler spring.

Can you suspend the parts on nail points or drive a nail into some hidden edge and dangle them from strings, or some such?

Re: OT keep latex painted parts from sticking together

#5

Re: something else to consider

Bill Hammond, Oregon Coast

>Bill, those are good points to consider, hanging by a nail or screw hole is a good idea, I am not discounting it, just worried that I am setting myself up for a mega-windchime effect and lots of dings and nicks to deal with. That and space to hang all the pieces is in short supply. At present they are leaned up against everything in my shop/garage and several times a day I move them to lesson the stick and paint peal. I am about to consider leaning them against the walls throughout the house and hope for the best. Perhaps some wax paper between them and the wall will help.

Bill

Re: OT keep latex painted parts from sticking together

#6

Re: OT keep latex painted parts from sticking toge

Keith Newton

>I bought a big roll of paper from Office Dep to transport some parts a while back, but it sounds like you are asking for problems if it is too green.

Try to find a place like the professional painters do to stand the parts in a room with no traffic. THey have a way of leaning one against the wall, and another leaning against its edge, and the next leaning aginst the edge of the one before.

You really have to be careful not to start a chain reaction though. But it really allows all of the surfaces to dry on down.

Re: OT keep latex painted parts from sticking together

#7

Jason Roehl in Lafayette, IN

Close...

Jason Roehl in Lafayette, IN

>Say you were leaning freshly painted shelves against a wall. Working L to R, you would lean one with a short edge on the floor parallel to the wall, and the opposing short edge against the wall. The next shelf would be at an angle to the first with an edge on the floor and only one corner touching the wall. The rest would be parallel to this one.

If you can imagine the wall above the ASCII text below they would look something like this on the floor:

-///// but the smaller angle would be more acute.

Jason (pro painter)

P.S. If they've been dry to the touch for a few days, the wax paper sandwich would work too without causing any problems.

Re: OT keep latex painted parts from sticking together

#8

Re: Close...

Bill Hammond, Oregon Coast

>well I'll know in the morning how well I did. Leaning against the wall with a small scrap of wax paper between the doors and the wall. Have to be careful tho or else the cats will knock them down.

Thanks all for the advice.

bill