Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Electric motor woes...

Posts

Electric motor woes...

#1

JL

Electric motor woes...

JL

>or maybe not. My old table saw motor stopped working. Hmmm - repair it or use it as an excuse to finally get the cabinet saw. Hmmmm.

Anyway, it just hums rather than starts. I cleaned it, lubed it and it still hums. Probably just the capacitor. I got it to "start" briefly by tugging on the belt.

Re: Electric motor woes...

#2

Re: Electric motor woes...

Denis Ch�nard, Orl�ans, Ont.

>If by pulling on the belt the motor starts and runs normally, then it would be the start capacitor.

Check if the motor gets hot. If it does then the centrifugal switch is stuck in the on position, don't let the motor run. Change that switch (might just need a blast of compressed air) and you'll be OK.

DC

Re: Electric motor woes...

#3

Re: Electric motor woes...

George@Colonel's Workshop-Havertown PA

>Good Afternoon JL,

It sounds like the starting circuit needs attention. Mine acted like that but a motor shop got me up and running pretty quickly. It needed a flux capacitor. :<)

George

Re: Electric motor woes...

#4

It needs to be replaced

Mark Goodall - ATL - tooljunkie

>Hi JL,

I'm afraid it needs to be replaced, but you already knew that.

Go ahead and replace the whole saw with a new cabinet saw. Then once you've used it for a while, you'll be feeling much better and you'll be thinking more clearly. Then you'll be able to fix your old saw, by replacing the cord or pressing the reset button, etc. and then you'll have two saws to enjoy.

No, no, no... don't thank me... it's my pleasure! ;)

Happy Woodworking!

Re: Electric motor woes...

#5

Milk it for a new saw, then . . .

SteveM

>you'll have a spare ! You'll sleep better !

Re: Electric motor woes...

#6

Re: Electric motor woes...

Dan Donaldson

>Could also be dirt in the contacts of the start switch. Try blowing it out with air and see if that helps. If not, and you feel comfortable doing it, take the end off the motor and clean the centrifugal switch contacts. Just be careful to note how it goes together and watch the springs.

Re: Electric motor woes...

#7

JL

Re: Took it in for diagnostics...

JL

>OK. Maybe I'm not clear on the concept. What makes a 1 hp motor a 1 hp motor. The motor guy says that my motor is not really a 1 hp motor.

The motor draws about 13.5 amps. It is labeled 1 hp. Why isn't it a 1 hp motor??

As I do the math, 13.5 amps x 120 V = 1620 watts. Assuming a 70% efficiency, that should be 1134 watts. If I have a 60% efficiency, that should be 972 watts. So call it anywhere from 1.5 down to 1.3 hp. At 50% efficiency that would be 1.1 hp.

I measured the current draw a while back and it was at least 12-13 amps.

Re: Electric motor woes...

#8

Hmmmm.....

Mark Goodall - ATL - tooljunkie

>Who is this guy telling you that?

Perhaps he meant: "It's not a 1-HP motor..... anymore, because it's dead and now is a 0-HP motor"

Reagardless of that, what does he say is WRONG with it?

Happy Woodworking!

Re: Electric motor woes...

#9

It just hums?

Forrest Addy

>Chances are it hums because it doesn't know the words. Nyuk! Nyuk! Nyuk!

Not a 1 HP motor? At 13.1 Amps it's probably an older 1.15 duty cycle motor and that puts if in the ballpark for a 1 HP motor. Chances are it needs a new start capacitor.

Regardless it ruined your saw and now you have to get another one - and a jointer and a...

Re: Electric motor woes...

#10

I thought I had a bad capacitor...

John @ Doraville

>...went to an electric motor repair shop in the neighborhood. Told the young fellow what the symptoms were. He said capacitors rarely go bad. Said to blow the dust out of the motor. Did it with a leaf blower. Been working for over 10 years now. No charge for the advice and he could have taken me for quite a few bucks.

Re: Electric motor woes...

#11

Re: I thought I had a bad capacitor...

Dan Manturi

>Disagree that capacitors rarely go bad. I have replaced 3 on my pool filter motor (1.5 hp same as a table saw) and one on the old contractors saw. Also had a problem where the capacitor did not fix it and, for no good reason, I pulled the motor apart, used compressed air to clean it up, put it bac together, and it worked fine. Capacitors can be strange in pricing - a pool store will charge $40, and Grainger gets $10 for the same thing. They are typcially a $15 item depending on volts and MFD rating.

Try it.

Re: Electric motor woes...

#12

JL

Re: Motor is back....

JL

>It was dirty (it isn't a TEFC). One of the leads had broken and the starting relay was "intermittent". Total cost of repair, cleaning and diagnosis was $75. Darn, so I'll have to wait for a cabinet saw.

I asked him to price a newer motor.