Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Quick note on safety

Posts

Quick note on safety

#1

Quick note on safety

Mark inb'ham

>I did a dumb thing last night and ended up with a chisel in my hand. I picked up a small piece that I was trimming a tenon on and pushed the chisel toward my other hand. It was a glancing cut and didn't require stitches, but it could have pretty easily.

Got me to thinking how carefully I set up each cut on a table saw, but with a hand tool like a chisel I just start cutting. Reminds me to slow down and set up those cuts too.

Okay, back to work and be careful.

Re: Quick note on safety

#2

Where will it go if it slips?

Rod Peterson -- Ormond Beach

>Someone once wrote a safety article with the above title (I can't seem to put my fingers on it). The actual content of the article probably isn't so important as adopting the philosophy espoused in the title. If you always think of that before putting muscle to the tool, your chance of an incident such as you describe is dramatically reduced.

Rod

Re: Quick note on safety

#3

IIRC

Bruce, a MN Galoot

>I remember it as the lesson learned in a story told by Steve Lamantia in the early days of the wreck. He was planing something, it slipped and the trusty jointer flew out the window of his shop, told in Steve's inimitable style.

Bruce

Re: Quick note on safety

#4

Re: Quick note on safety

Michael Wangler in Rochester, NY

>Mark,

Always pays to know where the blade will go if something gives loose. I found out the hard way a number of years ago. I was trimming a shoulder on a tenon. I was holding the wood in my hand rather than using my bench. I ran the chisel into my middle finger and I required 6 stitches. Luckly I did not hit any thing major....

Be safe,

Michael

Re: Quick note on safety

#5

Re: Quick note on safety

Bill Falberg

>If you need a constant reminder, just copy, paste, and print this:


img

Re: Quick note on safety

#6

It was definitely Steve…

Rod Peterson -- Ormond Beach

>…he mentioned it in a backchannel exchange we had a couple of years ago when I found out he's practically a neighbor.

Rod

Re: Quick note on safety

#7

Re: It was definitely Steve�

Bruce, a MN Galoot

>Where does he live now? I lost track of him when he left Washington. Along with Geoff Mason, Mike Davies and me, he was one of the original galoots.

Bruce

Re: Quick note on safety

#8

Does anyone know if the atricle still exists?

Gary Camp Bend, Oregon

>

Re: Quick note on safety

#9

Re: Does anyone know if the atricle still exists?

Rod Peterson -- Ormond Beach

>I never actually saw it. Steve mentioned that he had written it and that it was entitled “A Woodcarver's Mantra.” Frankly, I think the catch phrase (or subtitle, if you will) I mentioned characterizes all that needs to be said on the subject (although there might have been other stuff worth reading in it). A quick internet search on that title or the phrase I mentioned earlier failed to yield anything useful.

Rod

Re: Quick note on safety

#10

Seems like I do that once a month...

John in New Mexico

>or something similar. Made a big knuckle flap while changing planer blades in July... August I was shifting the truck into 4 low and jammed my thumb into a pencil sticking out of a cubby in the dash. Went about 3/8" in under the nail...

Just glad I never seem to do that dumb stuff with the power tools.

John (not looking forward to September!)

Re: Quick note on safety

#11

I make it a point to post a confession here....

Mark inb'ham

>whenever I do something dumb and get hurt. Maybe it will shame me into being more careful. Thanks for helping give me a kick in the pants to work safe.

Re: Quick note on safety

#12

cordless drill

JKJ in East TN

>>Just glad I never seem to do that dumb stuff with the power tools.

I think carefully about possible paths of slippage (both tool slipage and person slippage) and I'm extremely cautious around power tools with spinning blades. But years ago I did a dumb one with a lowly cordless drill. The small diameter bit pulled through the work far faster than I had expected and I drilled right into the clamp. Unfortunately, that part of the clamp consisted of my left index finger. The finger and nail eventually healed OK, but taught me acute awareness of the projections of drill bit paths.

I personally would rather read about ways to get hurt since in the case of woodworking safety, learning by example is far better than hands-on experience.

JKJ

Re: Quick note on safety

#13

Here it is... *LINK*

awh

>(see link below)




Tony Haukap

Home Page - http://www.cyberspace.org/~awh/

--


"If it slips, where's it gonna go?"

Re: Quick note on safety

#14

Thank you

Gary Camp Bend, Oregon

>My crew and I used that general topic for a safety disscussion on the way up to the mt. today. I think the quote "If it slips, where's it gonna go?" should be every "hands on" type worker's mantra. I will be reminding more of my co-workers about this in the coming days.

thanks again

glc