Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Advice needed on floor

Posts

Advice needed on floor

#1

Advice needed on floor

Nathan

>Hi all, it's been a long time since I checked in here... of course, I'm doing so now because I need some help.

My wife has finally convinced me that it's time to do the upstairs floors. They will be tongue-and-groove pine boards, a tad over 1" thick (27 mm - I'm in Europe). I've already purchased those so their thickness is fixed.

The substrate is concrete which has been leveled using a special levelling mix so it's more or less dead flat.

I'm currently in the process of preparing the "stickers". These are thin boards that will be anchored to the concrete substrate and sit between it and the tongue-and-groove floorboards. I'm making the stickers from plainsawn 2" thick pine boards, so the dimensions are two-by-something inches. Now, the question is, what should the "something" be.

These pine floors will be in the three bedrooms, each of which opens onto the hallway. The hallway has an existing teak parquet floor (which is dazzling, BTW, but too expensive to have in all the rooms). Now, this existing teak floor in the hallway is 47mm (1.85") above the concrete substrate. Of course, I'd like to get the pine floor as close to level as possible with the teak floor. However, subtracting 1" (the thickness of the pine floorboards) from 1.85" you're left with 0.85" which, methinks, is not enough thickness for the stickers.

So what, in your opinion, is the minimum thickness for the stickers so as to minimize the height difference between the teak and the pine? Of course, I will make thresholds to disguise this difference but we still want to minimize it.

One piece of relevant information here: I decided to use screws instead of nails to attach the floorboards to the stickers. I'm planning to make a jig that will allow me to predrill through the groove into the sticker at a 45-degree angle.

Right now I'm thinking 1" thickness for the stickers, which puts the height difference at 0.15" (about 1/6"). Do you think this will be enough material to hold those floorboards to the stickers?

On a related note. I'm planning to space the stickers about 22" apart. Is this overkill given the floorboards are 1" thick?

Thanks for any and all replies.

Nathan in the Czech Republic

Re: Advice needed on floor

#2

Re: Advice needed on floor

Barry Irby

>I think .85" thick is enough thickness for the stickers. That's about 7/8". I would probably space them 16" OC, but since the boards are thicker than standard flooring here 22" may be enough. 16" would require substantially more screws. How wide are the floor boards? Makes a difference on the number of fasteners per square foot.

My other question would be how are you anchoring the stickers to the concrete floor? I would glue them with construction adhesive and then either nail or screw them. Is this a leveling slab over concrete or over wood. If it is a topping or leveling slab over wood, I would probably screw right through it into the wood below. If one of the stickers comes loose it may ruin the floor.

Here we nail in the tongue edge. Are you really going to screw in the groove side? I would set up a jig if necessary and putt he screw through the corner of the tongue. Actually double you need the jig. Find screws with small heads like trim screws if you must, but i think it will work.

I installed 2 X 6 T&G pine over beams on 32" centers. Used a big air powered framing nailer and ring shank nails. Put two at each beam. Worked great except it was a lot of grief to remove a piece later. Mine showed below as the ceiling and on top as the floor.

Re: Advice needed on floor

#3

Re: Advice needed on floor

Keith Newton

>Hey Nathan, I think I am with Barry on the standard practice of nailing through the tongue side.

I think I share your concern for the size of the sleepers. I think I would drop on down to something close to 16" OC, and glue them down with liquid nails, and screw them to the slab with tapcon screws on about the same distance down the length of the sleepers.

If this is an old structure, and you are not sure of whether the slab has a moisture barrier, I think I would shop for some kind of product to seal the slab before you apply the sleepers.

If you put the floor down dry, and it takes on moisture during wet periods, it will expand and buckle, and ruin our efforts, and all of the material to boot.

I am wondering if you might do well to search to see if there is a product which can be toweled on, that bonds and water-proofs the slab, the switch over to sheet-goods. If you can find a mastic product which can be spread with a trowel, that doesn't need a lot of fasteners, you will have a substrate that gives total support, and can be nailed anywhere from above, and no flexing between fasteners, and or moisture problems.

You might start by checking the moisture content of the slab. I am sorry I can't give you better answers. It seems that I have only added more questions. Good luck, K

Re: Advice needed on floor

#4

Re: Advice needed on floor

Andy Halterman: My globe has warmed

>Why not resaw those sleepers and get the floor levels the same? I put down solid oak floors on 5/8 ply ramset into concrete. I use 1.5" (that would be about 40mm for you metric folks) fasteners and go to town. It's 1 1/4" for the face nails. I put down the heavy poly film and then shoot the plywood in place and then it's on. Bonus for the resawing is you now have enough material for 11" centers which makes your floor even stronger.

Some random post mountain bike ride thoughts on a Saturday.

Sleboda.

Andy Halterman

Enjoying my well working AC in my new (used) GMC truck in Hendersonville, NC�