Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Overheating 3/4HP motor

Posts

Overheating 3/4HP motor

#1

Overheating 3/4HP motor

Bill Falberg

>Is there enough variation in line voltage on the electric power grid to cause the cronic overheating of a 3/4HP, Cap. Start, 110/220, TEFC farm duty Dayton motor? Every once in a while I get reports of the thermal shut-off tripping and generally weak performance from these otherwise good motors. After eliminating the obvious possibilities like long ext. cords, binding wheels\bearings, and excessive load, I'm down to considering the power supply as a possible source of the problem. It usually occurs when the weather is hot and it usually happens outdoors. Does anybody else use TEFC motors in direct sunlight? Has anyone tried re-wiring to 220 V. to solve the problem? Or will I have to make everyone in Colorado turn off their air conditioners while Damon runs his saw?

Re: Overheating 3/4HP motor

#2

Jesper, Denmark

Re: Overheating 3/4HP motor

Jesper, Denmark

>5000 foot elevation is getting close to borderline conditions for running the TEFC motor. If you then add some sunshine and hot temperatures and maybe a dark paint color on the motor......

Re: Overheating 3/4HP motor

#3

Re: Overheating 3/4HP motor

JKJ in East TN

>Check your line voltage at the motor. A long line, even if it's say 12/2 romex instead of an extension cord, can drop the voltage and cause increased current draw and increased heating. In that case, a switch to 220 may certainly help.

We had a pump in a spring house a long way from the house that kept burning up motors on 110v. Switching it to 220v solved the problem. Another time, I had a radial-arm saw running on marginal wiring which quit tripping the overload protection when I switched it to 220v - as a bonus, it gained a lot of pep when starting and seemed to have more power.

JKJ

Re: Overheating 3/4HP motor

#4

I'm with JKJ here

Bruce, a MN Galoot

>check the cord on the motor first.

Re: line voltage variation on the grid, the likely answer is a qualified no. There can be voltage variations, of course, but you would notice that in other ways, too, not just on the table saw motor. Lights dimming, refrigerator motors running erratically, TV acting funny. I work for a utility, and we regulate the voltage on the main feeders (14KV lines) within probably a 50 volt swing. By the time you step that down to household distribution, there is very little actual variation.

OF COURSE, that can all vary, depending on temperature, household load and high humidity all causing higher than average motor load. If it's a chronic problem, call your utility and ask them about local VAR support and the cable condition.

I'd check out the line going to the TS. That happened to me a few years ago, and when I swapped it out to a 12 gauge multistrand wire, the problem went away.

Bruce

Re: Overheating 3/4HP motor

#5

I'll agree with all so far......

John in NM

>Go ahead and swap to 220V, less voltage drop that way if thats the problem, and you could also paint the motor white, grey, or rig a little shade for it. None of these options are going to take long, and all could solve or at least reduce heat related problems.

John

PS - any idea where to get parts for a Do-All blade welder?

Re: Overheating 3/4HP motor

#6

Re: Overheating 3/4HP motor

Rick Christopherson

>First off, a 3/4 hp motor won't be drawing enough current by itself to cause an appreciable voltage drop in the lines unless something is drastically wrong with the wiring. Your full load current draw will be less than 7 amps, and just for comparison, this is almost half of what a bathroom hair dryer draws. However, other loads in the area can cause a voltage drop. Cooling equipment that is on the same subsystem within your facility can have an effect on other parts of the system.

The cooling fan on the motor is designed to dissipate heat generated by the motor, but it is not designed to dissipate heat caused by other means, such as the sun. If this motor is exposed to direct sunlight, you can have a temperature rise that is easily an extra 20 degrees above ambient. Running over temperature can cause components within the motor to expand and the added friction can cause a loss of output power.

The same is true for the thermal overload protection. Even if the motor wasn�t exposed to direct sunlight, the thermal overloads could be, and this will result in their activation well below the normal current levels.

Another aspect is the duty cycle of the motor itself. If the duty cycle of this motor was related to temperature, and the motor was starting and stopping frequently, then the temperature of the motor will be higher than if the motor remained running continuously.

Because this is such a small motor, it is doubtful that rewiring it for 240 volts would correct the problem. If you have a line drop at 120 volts, you will probably still have a line drop at 240 volts too. That's because a line drop (if one exists) is probably not directly caused by this motor, but by another device.

Re: Overheating 3/4HP motor

#7

Re: Overheating 3/4HP motor

Dave Anderson (PacNW)

>ould you have a motor with a bad overheat switch?

Re: Overheating 3/4HP motor

#8

Getting hot

Lee Schierer - McKean, PA

>I would check the line voltage right after the motor trips on one of those hot days. Chance are you will find that the line voltage is low do to the total depand on the power grid. Brown outs (low voltage)are known to be bad for motors. If your line voltage is dropping on warm days due to total power grid demand, switching to 220 may not help as it will also see a volatge drop.

I would also like to hear an explanation of why altitude would have an effect on a TEFC motor.

Lee

Re: Overheating 3/4HP motor

#9

Re: It's "DoAll"

Al Stokka - Cambridge, Iowa

>DoAll Company

http://www.doall.com/

Re: Overheating 3/4HP motor

#10

Yeah, been there....

John in New Mexico

>Not really a site designed for selling little bits to secondhand tool owners. I'm hoping to find a resale vendor that everyone but me knows about ;).

John

Re: Overheating 3/4HP motor

#11

Jesper, Denmark

Altitude.....

Jesper, Denmark

>Simple, lower density air = less cooling.

Re: Overheating 3/4HP motor

#12

Re: Try again?

Al Stokka - Cambridge, Iowa

>John,

Click on the "Contact" link at the upper right of the page and select the dealer nearest you. Doing so, I was able to quickly obtain tires and guides for a metal-cutting band saw that is at least 40 years old. If I remember correct (my notes are at work), the dealer I contacted was in the Chicago area. Very helpful.

Al

Re: Overheating 3/4HP motor

#13

I will, thanks Al...

John in New Mexico

>I had assumed that would just give me an email address, phone #, etc for the headquarters. I'll go back and see what I can find.

John

Re: Overheating 3/4HP motor

#14

altitude & heat

Curt Harms

>Air cooled piston aircraft engines at high altitudes have the same problem with overheating How in the world can an air cooled engine overheat when the temperature is -20 degrees or colder? Same idea as Jesper alluded to, the air is plenty cold but there isn't much of it.

Re: Overheating 3/4HP motor

#15

Re: Getting hot

Bill Falberg

>Thanks for the benefit of your combined experience on this. It's opened some new insights and I'll be adding these thoughts to my Falberg Saw "Trouble-Shooting Guide" where it can be shared by some hard-working timber framers out there in the sun. Apparently these individual factors, minor by themselves, can pile up together to create a major PITA.