Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

A/V Cabinet: How would you vent this?

Posts

A/V Cabinet: How would you vent this?

#1

A/V Cabinet: How would you vent this?

David Hay @ Denver

>So I built these built in bookshelves to, in part, hold some A/V equipment (receiver, DVD player, etc.) I didn't really understand how hot this stuff can get until I accidently left the receiver on all night. So now I need to figure out how to cool the cabinet. The A/V stuff is behind the center left door, next to the bank of drawers. (The picture is a bit old...the baseboard has been installed)

I'm planning on putting a vent fan or two (kinda like PC fans) at the back of the cabinet, blowing up into the TV area. I'm not convinced that there's enough venting around the door to allow for decent airflow in the cabinet, so I'm looking for options on how to add a vent at the bottom of the cabinet, should I need to. Here's the options I'm considering:



  1. Cut one or more slots in the bottom of the cabinet and then put a vent in the baseboard below the door (the base of the cabinet is hollow.


  2. Cut one or more slots in the bottom of the cabinet and route some air holes through to the baseboard in the desk area.


  3. Cut a slot/hole in the left side of the cabinet and put a vent on the left side of the drawer bank cabinet.



Any other ideas I might consider?

Thanks!

David

Built in Bookshelves

Re: A/V Cabinet: How would you vent this?

#2

Re: A/V Cabinet: How would you vent this?

Dana McNeil in Peoria, Il

>Hi David,

Here is what I did when I built our entertainment center. I cut out the backs of the cabinets where equipment was located and covered the areas that were visible (I had glass doors) with speaker cloth. I left the hole behind the TV open to allow more airflow since the TV covered the whole pretty well. I would think in your case you could have the back of the cab of open since you have doors covering the equipment and that should allow air flow and coolong as long as the cab is not tight against the wall.

Part will depend on how much amp you have and how hot it gets along with how many pieces you have stacked on it. I had each piece of equipment on seperate shelves for better cooling.

Anyway that is what I did and never had any problems with equipment. Sorry that I can't show pics, but that piece of furniture is long gone to a new home.

HTH

Dana McNeil

Re: A/V Cabinet: How would you vent this?

#3

Re: A/V Cabinet: How would you vent this?

Michael Wangler in Rochester, NY

>David,

I have a built-in cabinet next to our gas fireplace which holds all our AV equipment. The cabinet does get pretty warm from all the equipment. The fireplace itself actually does not put out too much heat in the cabinet.

I cut a vent in the floor below the cabinet for venting. I cut a 3"x9" opening and have a 5" 'PC' type fan that 'feeds' the cabinet. I used a floor register to convert from the floor opening to the fan. The cabinet has a door on the front and I positioned the door so the gap at the top is a bit stronger than the bottom. The fan does a good job of moving the air.

A few benefits of having the floor cut out included moving cool air from the basement to the cabinet. Also the fan is actually in the basement so the sound is not that loud. If the fan was in the cabinet it might be louder than you think. Also the receiver has a plug on the back which actaully turn on the fan.

Good luck,

Michael

Re: A/V Cabinet: How would you vent this?

#4

Re: A/V Cabinet: How would you vent this? *LINK*

Paul Dwight

>You need to provide a route for air to flow through the entire cabinet and over the components. Because hot air rises, the usual design has air entering the cabinet at the bottom and exiting the cabinet as high as possible. If your design has the air both entering and exiting the cabinet at the bottom, you'll get very nice air flow on the bottom shelf and none of the components above will see any relief.

If the cabinet sets up off the floor on legs, the low, inlet vent can easily be located on the bottom of the cabinet. If the cabinet has no legs -- like yours -- the inlet vent can be hidden in the toe kick.

Normally the high, exit vent is mounted on the rear of the cabinet. If that's not possible, you can sometimes provide adequate air flow by leaving a gap between the face frame and the cabinet top -- concealing the gap by letting the top overhang the face frame an inch or two.

With your existing cabinet, you can work out a means of getting air into the cabinet at the bottom. The real problem is how you get the hot air out of the cabinet at the top. I assume the cabinet is mounted hard against the rear wall. I would first look at what's on the other side of that wall. Can you put a vent through the wall? This might work if, for example, there's a good-sized closet on the other side of the wall.

If venting through the wall is not practical, I would probably open a vent between the electronics cabinet and the drawer cabinet next to it, and then put another vent in the opposite side of the drawer cabinet so that the hot air dumps into the open area at the center of the desk (where your legs would be if you were sitting at the desk). Put both exit vents as high and as far back as possible. Put a fan in the bottom of the cabinet to push fresh air into the cabinet and another fan in the last exit vent to pull hot air out of the cabinets. (Be sure you orient the fans correctly to get the push-pull effect.) As someone else mentioned, the fans can be plugged into the switched outlet on your receiver so they only come on when the receiver is powered up.

If you have solid shelves in the electronics cabinet you'll probably need to cut some holes to allow good air flow through and around the components.

If you look around you can find fans that mount in round holes, which makes it easy to use a hole saw in a drill to retrofit the fans in an existing cabinet. The link below shows one such fan I have used in the past. If you look around on the site a bit they also have some pretty good general information about venting electronics cabinets.

Hope this helps! -- Paul


Round vent fans at coolcomponents.com

Re: A/V Cabinet: How would you vent this?

#5

Re: A/V Cabinet: How would you vent this?

David Hay @ Denver

>Thanks for the ideas. This is a built-in cabinet, so the back is up against the wall...can't leave it open. I do have the equipment on separate shelves, so at least I don't have stuff stacked on top of each other.

David

Re: A/V Cabinet: How would you vent this?

#6

Easy, but maybe not best way......

Mark Goodall - ATL - tooljunkie

>I know companies that cool there server rooms with these.

Strategically placed behind equipment to increase airflow out of densely installed electronic equipment.

I certainly don't promote it, but not eveyone listens to me or can afford to listen to me ;)

Happy Woodworking!


img

Re: A/V Cabinet: How would you vent this?

#7

Re: A/V Cabinet: How would you vent this?

Ed Mulligan, Cape Cod

>I'd shave 1/16 - 1/8" off the lower door rails on the inside surfaces to let in air, and put a couple of holes in the top toward the back (under the TV) for exhaust. If the holes are long slots you won't need a grille. Best not to cover them with fabric as this will reduce flow. Cut holes in the shelves or shorten them so they have an open space at the back.

You'll get the best airflow if the path is direct, i.e. no twists and turns.

Ed

Re: A/V Cabinet: How would you vent this?

#8

Re: A/V Cabinet: How would you vent this?

David Hay @ Denver

>That would actually be a great solution! Unfortunately, the room is on a cement slab, no basement :(

Thanks!

David

Re: A/V Cabinet: How would you vent this?

#9

Re: Thanks!

David Hay @ Denver

>Thanks all...it sounds like I'm thinking along the right lines here. I was planning on adding the vent holes/fan at the back top of the cabinet (behind the TV). The shelves are currently short enough that there is a bit of space behind and in front of them to allow for power and other cables. Sounds like it might not be a bad idea to put a few holes/slots in the shelves if I'm not getting enough airflow.

If I go the route of putting a slot or two in the bottom of the cabinet and providing airflow through the toekick/base in some way...any suggestions on how to make the slots such that stuff won't be inclined to fall through and out of reach?

Thanks!

David

Re: A/V Cabinet: How would you vent this?

#10

Re: A/V Cabinet: How would you vent this?

Scott in Montana

>Hello David,

I'm guessing by your tag that you live in Denver. I worked for many years at ListenUp in Denver designing high-end A/V systems. One solution that I didn't see mentioned was using the stud space behind the entertainment system. If it is not an insulated wall you could put holes through the cabinetry near the top of the equipment enclosure into the stud space behind and also drill an equivilent amount of holes through the sheetrock above the cabinetry, I see there is a space there. This combined with your idea of venting the toe kick would provide a great deal of air movement.

Re: A/V Cabinet: How would you vent this?

#11

Re: Thanks!

Thomas S Stockton

>Mockett .com offers some real cool vent covers. Another option would be to modify a wooden heat register cover, the come in a lot of different woods. Home depot carries some nice perferated black sheet metal that you cold attach to the underside/backside.

Tom

Re: A/V Cabinet: How would you vent this?

#12

Re: A/V Cabinet: How would you vent this?

David Hay @ Denver

>That's a great idea! Unfortunately, it won't work in this case, since the wall is insulated (exterior).

Any suggestions on how to determine how big to make the openings for the venting?

David

Re: A/V Cabinet: How would you vent this?

#13

Re: A/V Cabinet: How would you vent this?

Scott in Montana

>Yup, I have an informal rule. Two 1 1/4" to 1 1/2" holes at the top and the bottom for each piece of heat producing equipment. A surround sound receiver and a cable box would need four holes at the top of the enclosure and four at the bottom (or wherever the air comes in low). Most CD players, DVD players, VCR's and the like don't produce enough heat to bother with unless they have tube circuitry. Also remember that these components are designed to run at ambient temperatures of up to 120 degrees. And some perform best when ran at these higher temperatures.

Sorry for the late responce, I was working on a system in Colorado and just got home.

Scott