Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Adjusting drive belt on Performax question?

Posts

Adjusting drive belt on Performax question?

#1

Adjusting drive belt on Performax question?

Barry Irby

>I have a 16/32 Performax I bought used. The original drive belt was beat up, had ragged edges, but was functional. At some point I tried to make it track better and screwed up to the point it tracked into the control box and tore itself up. I found the adjustment process to be a little confusing. (I have left/right orientation "issues").

I bought and installed a new belt and it has been running for months, but it is too loose and tracking over toward the control box. I have left it alone because it does not appear to be doing any damage, but lately it has started to slip and fails to drive the pieces through. Time to adjust it again. (Insert trepidation here)

Can someone talk me through this? From the outbound end if I tighten one side more than the other does the belt move toward the tight side or the looser side?

Re: Adjusting drive belt on Performax question?

#2

Re: Adjusting drive belt on Performax question?

Ron Hildreth, Alta, Iowa

>Barry,

Picture a well oiled cone that you're trying to pick up with your fingers. The tighter you grip the cone, the faster your fingers slip off the top. Lay that cone on it's side, cone point toward the right, and you'll understand what your drive belt is going through. In your case, tighten the right side of the drive belt (as you face the in-feed side of your machine ).

Another way to put it- the rollers are not parallel, and the belt will always run off the side that is smaller between the two unparallel rollers.

Hope that helps! Maybe someone else has a better explaination!

Ron in Iowa

Re: Adjusting drive belt on Performax question?

#3

Re: Adjusting drive belt on Performax question?

DizD

>I have the same machine also bought used and also have replaced belt. One thing I found on mine was ceramic guide blocks under the table to guide the edge of the belt. Picture a horizontal U - the belt edge runs between the prongs. As I recall these are mentioned in parts list but not on exploded parts view. You might want to see if you can add these to help keep belt aligned.

My biggest issue currently is the right hand abrasive strip clamp not holding adequately. Thinking of replacing it - has anyone had any luck doing this?

Re: Adjusting drive belt on Performax question?

#4

Re: Adjusting drive belt on Performax question?

Doug Reynolds in Seattle

>Try this web site for more information: http://www.joewoodworker.com/performax.htm#3.

Also, some folks recommend an upgrade in belts over the stock one. Mylar or something like that instead of cloth as the backer is one choice. I think Kligspor (sp?) or someone else sells them. Perhaps someone else can chime in with better information.

Re: Adjusting drive belt on Performax question?

#5

Re: Adjusting drive belt on Performax question?

Paul Waddle

>Hi, don't have a performax but,but my stroke sander adjusts like this: the side you tighten,causes the belt to run over the other side. Be cautions,I'm not sure how fast your belt runs,I'd adjust both sides of belt until it was tight,stand by the switch,tighten one side a little more,be ready to turn machine off if it doesn't track(don't want it to run against one side and tear itself up). Once you get it to sorta track,make minute adjustments and watch it carefully for several minutes carrying a load. pw

Re: Adjusting drive belt on Performax question?

#6

Re: Adjusting drive belt on Performax question?

Kirk (KC) Constable

>No help from here. I've never been able to get mine to track properly... and I've fiddled with it for HOURS. Replaced parts, etc. Now I just accept the fact that I have to watch it, and 'scoot' it back to the other extreme every three or four minutes of use.

KC