Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

DC on TS Over thinking it again?

Posts

DC on TS Over thinking it again?

#1

DC on TS Over thinking it again?

Barry Irby

>I have made a chute that encloses the blade of my contractor's saw under the table. It works well, but there is still a certain amount that is thrown off the top of the blade. I know the usual answer is to install an over the blade pickup, but my shop is small and cluttered, I don't want to.

Wonder what would happen if you set up a compressed air nozzle blowing cross ways through the teeth of the blade inside the chute? If you blew 90 psi air through there, could you knock the dust out of the gullets before it rode back up and flew directly into your eyeballs? Another question would be if some of the dust were created as the blade came back up through the wood?

Re: DC on TS Over thinking it again?

#2

Re: DC on TS Over thinking it again?

Ron Hildreth, Alta, Iowa

>Barry,

Sorry, not to make fun of your idea, but you adding air at 90psi under your blade gives me a mental picture of someone sneezing in the talcum powder! Guess it might be worth a try, but at least funny!!

Ron in Iowa

Re: DC on TS Over thinking it again?

#3

Re: DC on TS Over thinking it again?

Barry Irby

>Ron, woodworking is a hobby for me. I really don't make much money at it, but it provides me a lot of entertainment. I also like problem solving and being inventive. If all I (or you) get is a few laughs, sometimes that's enough.

Re: DC on TS Over thinking it again?

#4

Re: DC on TS Over thinking it again?

Ron Hildreth, Alta, Iowa

>Barry,

I agree! Good luck with it, and if you get it figured out, let us know. You've also peaked my curiosity!

Ron in Iowa

Re: DC on TS Over thinking it again?

#5

Re: DC on TS Over thinking it again?

Howard Acheson

>>> Another question would be if some of the dust were created as the blade came back up through the wood?

If your blade is not perfectly parallel to the miter slot, you could be getting some additional cutting at the back of the blade. If your miter gauge is not producing an exacty 90 degree cut you will always get recutting at the back of a cross cut.

Generally if your blade is set too high, you will be more likely to get sawdust above the board. Set the blade height so that just one tooth is above the board.

Re: DC on TS Over thinking it again?

#6

Re: Over blade dust pickup

Joanne Adler in Pt. Pleasant, PA

>Hey Barry,

Any chance of installing an overhead guard/dust chute by suspending it from the ceiling? Although I now have plenty of room (sorry, don't mean to gloat), I didn't want to waste room around the saw and hung the overhead guard from the ceiling.

Re: DC on TS Over thinking it again?

#7

Re: Over blade dust pickup

Barry Irby

>I have the TS about five feet inside the overhead garage door. If I want to rip something longer, I open the door. If you are quick, stuff doesn't get to wet if it is raining.

I keep staring at the track of the door, cyphering on how to attach a brace to the track to allow for a hose to hang straight down. I am thinking of a piece of aluminum tubing like the dryer ducting without any fancy over the blade guard. If I position it just above the blade, I think it will get most of the big stuff and even more of the really fine stuff. If it's in the way it will swing and then return. If the blade hits it, no harm done.

My best friend's father would have rather made something than buy it. Or fix a broken one than have a new one. Someone gave him a broken pick (like you dig a hole with) and he welded the point back on it. The point was crooked. I laughed and said, "Well that's the end of that." He said "No!, I'll just cut it off and weld it again." When he died, my friend gave me the pick. So, I would rather figure it out and have a DC that work pretty well than spend the money on a store bought one. If you don't understand, You never will. If you do understand, that's good, because I really can't explain it.

Re: DC on TS Over thinking it again?

#8

Re: DC on TS Over thinking it again?

Gary Camp Bend, Oregon

>Ya know I have an old Craftsman saw, (one of the speedometer cable drives). It has a clear plastic blade gaurd. Use the blade gaurd when ever the cut allows. The blade gaurd contains 90 % of the sawdust the dust collector doesn't grab. My Grizzley saw at work had a stock blade gaurd that I hated, fixed top arm, floppy, slotted metal sides, hard to remove. I found a Craftsmen gaurd at a garage sale for a buck, with a bit of work I had a more functional gaurd and it contains 90% of the sawdust too, even without a collection system. I do understand the fix it or make it philosophy

glc