Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Blastgate fit issues

Posts

Blastgate fit issues

#1

Blastgate fit issues

Earl

>Greetings,

I am installing the metal ductwork for my dust collection system. I have noticed that ALL blastgates (regardless of vendor) seem to fit very loose in the appropriate sized pipe (e.g. 5" pipe with 5" blastgate=very loose fit).

What gives? Are there any good ideas regarding how to create a tight fit - ideally without spending more $$$ on an already expensive solution.

Dust collection cyclone + metal ductwork = Good lungs and NO $$$ left. Marriage at risk - help! ;-)

Thanks for your time and attention!

Earl.

Re: Blastgate fit issues

#2

I got one word for you

DB

>That word is caulking.

Try caulking the joints.

Re: Blastgate fit issues

#3

Re: Blastgate fit issues

Glenn Madsen near San Francisco

>Talking with my buddy this evening, as he was reinstalling his Oneida. He has a crimping tool for making the metal pipe smaller to slip fit into the next fitting. I have no idea what one costs, but I would bet a good hardware supplier, or sheet metal shop would know.

Re: Blastgate fit issues

#4

Re: Blastgate fit issues

Mark Kauder, Phenix City, AL

>You can get them at the big box stores for about $25. Another option, wrap the small one with duct tape, and then calk.

Mark

Re: Blastgate fit issues

#5

Duct Tape is your friend :)

Dave Peebles Lyons, Ohio!

>Like Mark said. I have found this every time I change my system.

It works great and is a cheap.... thrifty way to make things right.

Dave "quack" Peebles

Re: Blastgate fit issues

#6

I went to a *LINK*

Terry Quiram

>heating and cooling contractor and talked them out of a couple rolls of the silver duct tape. The pros use heavier tape than you can get at a borg store.

Terry


Eclispe

Re: Blastgate fit issues

#7

How loose is loose?

Marv

>Hi Earl,

How loose is loose? What are the actual dimensions of the two pipes? O.D of the small one and I.D. of the bigger one?

Marv

Re: Blastgate fit issues

#8

Re: Blastgate fit issues

Barry Irby

>I have used all of the above; Crimping tool, caulk, duct tape and foil tape.

I most cases I ripped a narrow strip of regular cloth duct tape and wrapped it around the male fitting on the blast gates and then put the pipe over that.

I used a mix of pipe on mine, some metal and some plastic. On the plastic pipe (thin wall schedule 35 Sewer & Drain PVC, AKA SCD 35 S & D) I cut slits into the end of the pipe about 3/4 or 1" and then used a hose clamp to compress the ends of the pipe onto the fitting. I tried cutting the finger on the bandsaw, but it took the small pieces away from=m me and through them around the shop at enormous speed (BAD Bandsaw, BAD). So on most of them I cut the slots with a jig saw and a metal cutting blade. Worked better. Cut slot about an inch apart.

On metal pipe you could cut fingers on the end with tin snips and then compress them.

The duct tape was supposed to be a filler and gasket. Not so good. The pressure of the clamp tends to cause the glue to turn liquid and the joints ooze apart. Did not want to put screws into the joints though because thy would provide a place for stuff to snag and block the pipe on the inside. If you "must" have screws, use short ones and put them in from the top.

One of mine fit so poorly I wrapped the male end oft eh gate with electrical wire and then clamped the fitting.

Re: Blastgate fit issues

#9

Re: Blastgate fit issues: Shortening screws

Kneale Brownson in Northern MI

>If you run your screw into the fitting and get the clamping effect you want, you can run the screw back out, grind off most of the threads and run it back in. Less likely to snag stuff, although I've used 1/2 and 3/4 screws on metal DC ductwork and never found anything snagged on them. Guess most of my planer and jointer chips are too small to snag on anything anyway.

Re: Blastgate fit issues

#10

I use black e-tape. You can add a bit at a time.

s.mackay@worldnet.att.net

>

Re: Blastgate fit issues

#11

Re: Blastgate fit issues

Steve Wilson

>I use rivets to attach metal pipe to blast gates and then calk.

Re: Blastgate fit issues

#12

Re: Duct Tape is your friend :)

John Veerkamp

>I'd advise against duck tape. It will desintegrate over time. For just a little more get the foil tpe used by HVAC installers. It is very sticky and will outlast the pipe. It is available at most hardware stores as well as the big box stores.

John

Re: Blastgate fit issues

#13

Re: Blastgate fit issues

s.mackay@worldnet.att.net

>At first I tried clamps and calk but the first clog was a nightmare. From then on I empty the vac and filter more than needed to compensate for any small leaks. After that last bandsaw fire that got into the vac someone had a couple weeks ago I figure thats not a bad idea anyway.