Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Frame and Panel Headboard

Posts

Frame and Panel Headboard

#1

Frame and Panel Headboard

Gordon Milliken

>Hi,

I'm new to the message board, but know many of you from articles, and other forums on the web - - and need some advice:

I'm making my son/fiance a queen size walnut frame and panel bed for a wedding present. This is the first time I've attempted anything this big, and also first time I've attempted to color wood (stain/dye) as I've always used only the color of the "clear" finish over natureal wood.

ok, here are the two issues I'm working - -

1) I'm planning three large panels across the headboard - 14 inch by 20 inch left and right, and a 24 x 20 inch panel in the center. I was thinking about using a single slab of figured walnut to create the three panels (1/2 inch?) so the figure would be continuous across the headboard (also doing a smaller version, 6 inch tall, on the footboard) - - - I know this will be really expensive - but am concerned about a solid board panel that big - wood movement? - would it be a lot smarter to use plywood, and laminate veneer if I want some neat figure? Or should it be all right to use the solid wood? I'm not too worried about cost - they only get married once....

2) My some has requested a pretty dark look - I made a sample with minwax red mahogany stain (2 coats) and he likes it ok, but wants it slightly darker, but still maintaining some of the red tone - - -sooo, am I wasting money by getting really expensive solid wood single board highly figured walnut, and then "painting" it with heavy stain?? Is there another way to develop the color without the heavy pigment?

All suggestions will be deeply appreciated

Thanks

Gordon

Re: Frame and Panel Headboard

#2

Re: Frame and Panel Headboard

Patrick Schupbach

>If it were me I would go with veneer. Less chance of wood movement, and more choices of figured goods. Check out joe woodworker.com for an awesome selection of veneer and supplies. Hope this helps!

Re: Frame and Panel Headboard

#3

Finish

Mike Fitterling

>I have been doing a walnut/maple kitchen. The designer wanted a very dark, dark, brown; instead we ended up spraying a couple coats of garnet shallac, followed by three coats of clear lacquer (two gloss, last satin). Everyone has been really pleased with the color and the figure of the walnut really shines through.

Re: Frame and Panel Headboard

#4

Re: Frame and Panel Headboard

Steve Schoene

>The twenty inch height of the panels seems a bit large for solid wood

running horizontally across the headboard. But I like the solid wood concept. It will also make for quite a high headboard, depending on the size of the rails. I would consider making the rails fairly wide and reduce the size of the panels somewhat. It seems to me that the lower rail should probably be widest. It should be wide enough that you still see a bit of rail below the panels when the bed is made up with pillows.

As far as staining, the way to get relatively dark colors is to use a dye. Analine dye can be mixed to be dark or like, depending on the concentration mix. Unlike pigmented stain it can become dark without "painting out" the wood grain. You can experiment with combinations--a dye not quite as dark as you want the final product to be, sealed, and then stained (a glaze actually) with pigment but not a nearly opaque mix. The combination often gives a lot of "depth" to the finish.

Re: Frame and Panel Headboard

#5

Some Suggestions...

Jim Rahbe, Bedford, TX

>Gordon,

Here is a picture of a Walnut Headboard that I did a couple of years ago as part of a bedroom set for our guest room. Three solid wood panels for a regular twin bed. The floating panels are about 13� x 13�. With a 2 �� curved rail at the top and 7� curved rail at the bottom. Here are a couple of things that you might want to keep in mind.

1. 95% of the time there are regular pillows and throw pillows on the bed, so most of the headboard can�t be seen unless I�m tying to show it off..

2. You only need to make the figured panels for what will show above the mattress.

3. You really need to know the size of the mattress and box springs before making the headboard (New mattresses are really tall compared to old ones like the one pictured)

4. May I suggest that you use Bed-bolts and mortise/tenons for connecting the side rails with the headboard and footboards

Using plywood would be easier, cheaper, and guarantee the amount of figure.. But�this is a hobby for me and it�s the pleasure I get from taking rough cut lumber and making it into something I can use that I enjoy. I try to use as little plywood as possible. If I were doing this as a business, I�d be using as much plywood as possible. But it�s not and I don�t�

I can�t be much help on the stain part as I generally just use clear lacquer.

Jim R.


img