Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Popping Curly Maple Grain

Posts

Popping Curly Maple Grain

#1

Popping Curly Maple Grain

Steven Pollack

>I bought this really nice piece of curly maple for a coffee table top. I have been googling for information about making the curly grain very distinct in the finished piece and there is a lot of contradictory information.

Can anyone add to the information about getting the best out if this piece? I would prefer to keep it white but will consider dyes if a good case can be made for doing so. I am also looking for suggestions for the final finish as well.

Thanks,

Steve


img

Re: Popping Curly Maple Grain

#2

Re: Popping Curly Maple Grain

Denis Ch�nard, Orl�ans, Ont.

>It would be interesting to hear about the conflicting information you found...

In any case, oil will pop the grain right out. Tung oil (the real stuff, read the label on the can) will not darken the wood as much as linseed oil, so if you want to keep the wood as pale as possible that would be a good choice.

Diluted blonde shellac works well too.

Topcoat with a waterbase finish (check for compatibility with the oil if you go that route, with shellac, if it's dewaxed you won't have any problems) to keep the color as pale as possible if that's you want.

DC

Re: Popping Curly Maple Grain

#3

JL

Gorgeous piece of wood!

JL

>

Re: Popping Curly Maple Grain

#4

Jim in Burlington Ont.

Natural light

Jim in Burlington On

>If you have a good source of natural light in the room I'd just sand it to 320 or 400 and shoot it with clear water based lacquer. Just the natural grain will shimmer. I'd certainly put on quite a few coats and sand it smooth up to 4000 grit with abralon pads then buff with Finessit or Perfect it from 3M.

Re: Popping Curly Maple Grain

#5

Re: Popping Curly Maple Grain

Moses Yoder in White Pigeon, MI

>Fine Woodworking did an article several years ago on finishing curly or birdseye maple by Jeff Jewitt. I am sure he recommended a stain though, I think a die stain followed by a wiping stain but would have to find the article to make sure. The stain would definitely bring out more of the figure but in this case with such fantastic wood I would put a clear finish on it. I'd use several coats of boiled linseed oil on it then finish with my mixture of turpentine, BLO, and polyurethane in equal portions. If you build something, save the scraps as test pieces for your finish. I think this would be an ideal piece of wood to just finish and hang on the wall somewhere.

Re: Popping Curly Maple Grain

#6

White paint?

Pat Evans

>With grain that messed up, you might want to just cover it up with white paint. :) Just kidding. Where did you find that piece? It's suitable for framing and hanging on the wall.

Re: Popping Curly Maple Grain

#7

Bart Goldberg

Waterlox would work very well and its easy!

Bart Goldberg

>

Re: Popping Curly Maple Grain

#8

Re: White paint? *LINK*

Steven Pollack

>http://www.exoticlumberinc.com/index.php

I bought this from Exotic Lumber Inc.

Steve


Lumber home

Re: Popping Curly Maple Grain

#9

My suggestion

Lee Schierer - McKean, PA

>My suggestion is to use a lacquer based finish like Deft Clear wood finish. It imparts minimal color change and does not noticeably yellow with age. Grain pops as you can see on the photo below.

Lee


img

Re: Popping Curly Maple Grain

#10

Re: My suggestion

Steven Pollack

>Wow! Thats really nice. I did not realize lacquer penetrated the wood. I thought it mostly sat on top.

Re: Popping Curly Maple Grain

#11

Re: Another alternative *LINK*

Dave Mount

>Link below is to a curly maple table top. This was 1 coat "natural" Danish oil, couple coats blonde shellac, then wipe on poly over that for durability. Danish oil step is not really necessary. I use shellac because it dries fast and sands well. Let's you completely fill the wood then sand it flat so the poly coat is dead flat. This approach does not impart a lot of color, but does add some amber/yellow as you can see. Depends on what you want for color. If the table won't see water, could just use shellac start to finish. A 1 or 1.5 pound cut of shellac as a first coat penetrates very well, which accentuates the curl.

Surface prep is as important as anything.

Best,

Dave

NE Minnesota


Curly maple table top

Re: Popping Curly Maple Grain

#12

Re: Popping Curly Maple Grain

Angus Barclay, in New Zealand

>Hello Steve,

my sugestion is about the design of the table for that lovely piece of wood, rather than advice on how to bring out the figure. Perhaps you should think about framing the top somehow. A narrow dark string inlay around the edge, a narrow frame in a contrasting wood with fine straight grain, or even a small crossbanding could all work. Giving the top a visual frame would make it more formal but could also subtly indicate that this is a genuine work of art (by Mother Nature).

regards

Angus Barclay

Re: Popping Curly Maple Grain

#13

Re: Popping Curly Maple Grain

Steven Pollack

>Hi Angus,

Thanks for the design advice. I have been struggling about what to do with the natural edge. The shape of it is sort of interesting but the edge itself is not particularly attractive.

I will post a picture of the edge tomorrow.

Steve

Re: Popping Curly Maple Grain

#14

Re: Popping Curly Maple Grain

Steven Pollack in Chicago

>Here is the live edge. What do you think, is it worth saving or would you suggest cutting it off to square up the piece for the frame?

Thanks,

Steve


img

Re: Popping Curly Maple Grain

#15

Re: Popping Curly Maple Grain

Steven Pollack in Chicago

>Here is my design concept for the piece. It does not really suggest using the live edge either but once I got the piece I wondered if it would be a crime to get rid of the live edge.

Like I said, the edge shape accentuates the grain but the color and look of the edge itself is not particularly attractive.

Steve


img

Re: Popping Curly Maple Grain

#16

Re: Popping Curly Maple Grain

Pat Evans

>Steve, have you considered framing the top as Angus suggested? I would think with the same contrasting wood as the legs. An ebony inlay separating them would be very classy, but perhaps more formal than you desire. To my non-artistic eye, the frame would accentuate the maple even more.

If you choose not to frame it, have you considered having the top inset into the top of the legs such that two sides of each corner of the top are concealed instead of just one? Or perhaps have the top sit on top of the legs with a reveal around the top of the leg to make the maple top appear to float?

Re: Popping Curly Maple Grain

#17

Re: Popping Curly Maple Grain

Angus Barclay, in New Zealand

>Hello Steve,

that is a really nice design. There isn't a frame there of any sort but the dark space between the rails and the top combine with the dark wood of the legs to provide a hint of visual framing to the top, which will really make that piece of wood stand out. I believe architechts and interior designers call this a "negative detail". What you've done is more subtle (and to my mind a whole lot more sophisticated) than simply framing the timber itself. It could be worth thinking about how to make sure that the space between the rails and top remains dark to the eye from perspectives other than the three-quarter view you've provided. Perhaps a different finish under the top, or maybe even just making sure the table is always sat on a dark-ish floor.

regards

Angus Barclay