Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

rust on cast iron table saw

Posts

rust on cast iron table saw

#1

rust on cast iron table saw

bruce

>I've recently purchased my first table saw with a cast iron top. One morning I found some rust spots on it and I am having great difficulty getting them off. I thought I had the top waxed well enough, but apparently not. Any advice on how to remove the rust spots (they don't appear to be very deep yet) and how to keep the top rust free in the future?

Re: rust on cast iron table saw

#2

Re: rust on cast iron table saw

Ray Binnicker

>Bruce,

I spray my cast iron surfaces with WD-40 (no affiliation) and rub the wet surface with 0000 steel wool. Wipe the slurry off with paper towels, rags, etc. and then apply a coat of paste wax. The wax won't last; using the machine will take the wax off so this will become a regular chore.

Good luck

Nathaniel Binnicker

Re: rust on cast iron table saw

#3

Re: rust on cast iron table saw

Ron Hildreth, Alta, Iowa

>Bruce,

Try WD-40 and 0000 steelwool- Rub a dub! As for keeping it that way, you might want to check the humidity level of the ambient air for starters, and then rewax with a heavy coat of a good quality automotive wax. Keep it waxed frequently!

Ron in Iowa

Re: rust on cast iron table saw

#4

Re: rust on cast iron table saw

john lucas

>Sounds like we are all in agreement. I had a shop in a basement that actually ran water when it rained. I used paste wax on everything. If I did get some rust I rubbed it out with 4/0 and WD-40

Re: rust on cast iron table saw

#5

Re: rust on cast iron table saw

Marv

>Hi Bruce,

Here's the way I remove rust like the kind you speak of. There's all kinds of rust. The kind you have is the easiest to remove. Use Mineral Spirits as a lubricant and get some 3M 220 black sandpaper. They sell it in a small pack of 220,340 & 400 grit. Get the whole pack. I buy mine at Wal*Mart. Start with the 220, the go to the 340 and finish up with the 400. Do the whole table surface, not just where the rust is. Do the sanding in one direction, probably from front to back. As the Mineral Spirits gets dark in color, wipe it off and brush on some more. Keep doing this until it stops turning dark or dirty. When you are done, and the surface dry and clean, spray the surface teflon that you can buy in an aersol can. I promise you, you will have a great looking surface. The teflon is fast and easy to apply time after time and it is a little more durable than wax, although wax is a good alternative.

Have fun,

Marv

Re: rust on cast iron table saw

#6

Re:CAUTION: rust on cast iron table saw

Kneale Brownson in Northern MI

>You don't want to "Oil" the surface, so follow the process of cleaning with mineral spirits.

Automotive waxes include water. Don't know why you'd want to wax with them. If you must use a paste wax, use one designed for wood surfaces.

I prefer TopCote as the protective treatment. I've used it on my tablesaws, jointers, planers, scroll saws and hand tools like big C-clamps. Like anything you use to protect metals, it needs occasional renewing. I respray with TopCote about three times a year.

Re: rust on cast iron table saw

#7

Wax - any wax - offers little protection

Forrest Addy

>Cast iron is very susceptable to rust. Wax - any wax - offers little protection from rust. About the most you can expect from wax alone is as a low friction coating. Waxing to prevent rust is at best ineffective.

If you have a rust problem you actually have a humidity problem. You need either a reduction of relative humidity, some kind of active corrosion inhibitor, raise the local temperature about 30 degrees above the ambinet dewpoint. or a treatment that lowers the surface Ph of the cast iron to 4.5 or so.

If the shop is located with the home laundry you're running a foot race wearing sho shoes. Between the bleach fumes and the humidity your saw table doesn't have much of a chance.

A dehumidifier in the shop is a good start. A better start is to separate the shop from humidity sources seal oof from high humidity ambient air and either air condition or dehumidify the space.

Assuming that dehumidification, separation etc s out; when the shop is idle a light spray of the table top with LPS2 or LPS3 rust preventative will actively prevent rust. You will have to clean and re-wax your saw table whenever you need it.

Tenting the saw with a thick blanket and a 150 watt light bulb underneath will raise the saw table temperature are enough above the dewpoint to prevent rust.

Lowering the surface PH of the saw table requires a protective coating like Parkerizing.

Wherever you have bare dry cast iron you will get rust so you might as well reconcile yourself to it. Learn the remedies and the cures. They all take time and/or are expensive.

Re: rust on cast iron table saw

#8

Re: rust on cast iron table saw

Lee Schierer - McKean, PA

>The best way to keep rust off your table saw is lots of use. Cast iron that sees heavy use doesn't rust and the shine is terrific. Paste wax application will make the goods slide right across. DOn't use automotive waxes as they contain water (water = rust) and most contain silicone which is bad for wood finishes. Just tell your wife and friends you have to go to the basement and do rust prevention on your table saw. Oh yeah, you'll also need to buy lots of wood to cut. :)

The best cleaning method I've ever seen is a scotch brite pad attached to a vibratory sander. Lightly flood the surface with mineral spirits and "sand" the entire surface. Wipe off the mineral spirits and apply wax.

For inactive periods wax won't stop rust if the humidity is high. For that protection you need something like Boeshield. Spraay it on leave it thick and recoat and wipe off when you are ready to work. Sure it takes extra time, but so does rust removal.

Wood Magazine did a test a few years ago and they tested various products for rust resistance on cast iron. Boeshield provided the most protection.

Lee

Re: rust on cast iron table saw

#9

Black vs red

Mark Goodall - ATL - tooljunkie

>If you've got red rust, that will possibly get on the wood and will affect the woods ability to slide on it, so remove it as the others have mentioned.

IF after that you still have black stains, they won't affect the slidability nor the wood, and as much as they might "Tarnish" the image of a nice shiny saw.... it's a fact of life and adds character to your tools.

Happy Woodworking!

Re: rust on cast iron table saw

#10

Re: rust on cast iron table saw *LINK*

Jim Dillon

>Bruce,

I originally used Topcoat as a protectant, but upon opening the garage door after a cool night on a humid spring day several years ago, I was left - much to my dismay - with a layer of rust. I cleaned the rust off with WD-40 and the Sandflex Abraser blocks sold by Kingspor. The combination worked well, at least in my case. I cleaned the top off with a dry rag and then applied several coats of Renaissance Wax (a very hard wax available from various suppliers) and keep the top now covered with a old flannel sheet when not in use. Seems to work OK. I recoat with wax maybe twice a year. I was tempted to use Boshield T-9 after seeing how well it worked on an iron lawn decoration, but have not found the need, so far. Good luck.

Jim


Sandflex Abraser Blocks

Re: rust on cast iron table saw

#11

Silicone free wax?

wilbur

>I've read that some waxes have silicone in them, which is bad for woodworking applications like rust protection, as the silicone may come off on the workpiece and screw up finishing later on. However, I've never been able to find which waxes might or might not have silicone in them. Does anyone have a source for this information?

Re: rust on cast iron table saw

#13

Water's worse

Mark Goodall - ATL - tooljunkie

>Alot of automotive waxes even containt water, which is worse.

Stick with Johnson's Paste Wax (red and yellow can, found in grocery stores) or use a product designed for cast iron tools.

Happy Woodworking!

Re: rust on cast iron table saw

#14

Re: rust on cast iron table saw

Pete in Holland, MI

>Cast iron and moisture are bad combinations. Garages get exposed to all sorts of climates. Heavy dew mornings or spring time thaws are the worst. While your saw is not in use, cover it with a piece of plywood, with border strips on the bottom to keep it alligned with the top. Dampen it with some motor oil. This'll shield the saw from the moisture in the air and protect it from flying stuff when not in operation.

Re: rust on cast iron table saw

#15

Re: rust on cast iron table saw

Kneale Brownson in Northern MI

>How old was your application of TopCote when the rusting occurred? I've used it for years and years without experiencing new rusting, but I reapply two or three times a year. First time I used it, I probably didn't reapply for about a year, and I had an experience similar to yours where warm, humid air entered a cold shop and I got a film of condensation on everything inside, which resulted in some rusting of all my cast iron stuff. My shop is an unheated barn, and TopCote has served me well since my first "lesson".

Re: rust on cast iron table saw

#16

Re: rust on cast iron table saw

Jim Dillon

>Kneale,

First, an apology for not catching your followup post sooner. I think you hit the nail on the head regarding my use (misuse?) of Topcoat. It may have been quite awhile since I had recoated the top of the tablesaw. That would indeed explain my experience. I had always heard good things about Topcoat, so I was surprised. I agree with your suggestion regarding the need to recoat several times a year.

Jim