Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Help w/Physical/ Aesthetic CG speaker stands *pic

Posts

Help w/Physical/ Aesthetic CG speaker stands *pic

#1

Help w/Physical/ Aesthetic CG speaker stands *pic

David Eisan

>Hello everyone,

I started on my first bit of woodworking not related to home renovations tonight for the first time in a real long time.

I lost the shelves that my small bookshelf speakers rested on and I wanted something to hold them off the floor beside the TV.

I almost got them done tonight but I got stuck with the physical and aesthetic center of gravity placement of the vertical post vs. the top and bottom platforms.

The speakers are 20 year old Infinity RS1000's that I replaced the main drivers in two years ago due to surround cracking from age.

I am at a loss at where the vertical post should meet the top and bottom platform so they look good and don't topple.


Any ideas?

Thanks,

David.

Every Neighbourhood has one, in Mine I'm Him

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#2

Re: Help w/Physical/ Aesthetic CG speaker stands *

Ed Mulligan, Cape Cod

>Since the post appears to be symmetric I'd center the mortises in the head and foot. Ed

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#3

Re: To find the balancing point...

Grant Smith

>maybe make a mock up out of framing lumber in order to determine a workable balancing point.

In the past when I built speaker stands for use on carpeted floors, I found that adding points to the outer corners of the base made them much more stable. You might find that if you try to place them on padded carpet, they are very tippy that high.

Most commercial speaker stands are shorter, but hold the speakers tipped back so they hit the listeners ears properly.

By the way, try to engineer in a speaker wire holding method to keep it out of sight. Maybe route a slot down the back of a leg or something.

FWIW,

Grant in Iowa

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#4

Ellis Walentine

Mockups

Ellis Walentine

>I agree that a mockup would be beneficial. You can just screw it together and change the locations of the top and bottom piece as needed. I must say I would be very concerned about the ratio of the height of these stands to the size of their footprint. At the very least, you would want to concentrate the load on the perimeter of the base. One way to do that would be to make a molding that goes around the base. It would add a fair amount of stability. You might also want to screw the speaker to the stand, to minimize the odds of it getting bumped off. You might even consider screwing the foot to the floor.

Ellis Walentine, Host

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#5

Re: Mockups

Ron Hildreth, Alta, Iowa

>I agree with Ellis, plus one other consideration to add. My speaker stands for my sound-surround all have very heavy bases. They out weigh the rest of the stand AND the speakers together. Yet they're small in foot print. The old adage of "Weebles wobble but they don't fall down" is a good comparison of my stands and the reason I bought them. If you can redesign the bases or use a very heavy material. That should help stabilize them.

Food for thought, anyway!

Ron in Iowa

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#6

Ellis Walentine

Loaders

Ellis Walentine

>When I was making floor lamps many years ago, we used heavy, flat, circular, cast iron counterweights called "loaders" in the bases of the lamps to keep the center of gravity low and help the lamp resist falling over. I have a 5'-tall floor lamp in my living room that has never tipped over in 25 years thanks to the weight in its base.

If you don't intend to screw all the relevant parts together, consider installing loaders. Lamp parts companies, such as Kirk's Lane, sell them in different sizes.

I still think you need to increase the footprint.

Ellis

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#7

Re: Help w/Physical/ Aesthetic CG speaker stands *

Phil Thien

>What Ed said.

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#8

How about

Dan Donaldson

>Get a plate from a set of weights, maybe a 25 pounder, and build it into the base

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#9

Re: How about

Kneale Brownson in Northern MI

>Could he hollow out most of the base and pour it full of lead?

Re: Help w/Physical/ Aesthetic CG speaker stands *pic

#10

Re: How about

Dan Donaldson

>That would probably work, but the weight plate would be a lot less expensive.