Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Sort of Interesting OSB Observation?

Posts

Sort of Interesting OSB Observation?

#1

Sort of Interesting OSB Observation?

Barry Irby

>I have no idea how they make Oriented Strand Board. I assume it was one piece at a time and that somehow they coated those flakes of wood with glue and put them in layers with their little strands oriented, pressed them into sheets and trimmed the edges.

Recently I was walking under a house that was raised on pilings and looked up at the OSB nailed to the bottom of the joists. I happened to notice two sheets end to end that appeared to be "matched". It was clear that they had been a single piece and then cut apart. They were both full sized sheets. The flakes were lined up in such a way that you could see they continues from piece to piece, exactly as if you had cut a piece in half with a skilsaw and left the two pieces laying where you cut them.

I just thought it was interesting that these two pieces had been manufactured end to end and remained "in sequence" and been installed in the same position they had been manufactured in. Also means they must make it on a more continuous basis adn slice them off the end.

Never mind, I need a hobby.

Re: Sort of Interesting OSB Observation?

#2

Re: Sort of Interesting OSB Observation?

Kneale Brownson in Northern MI

>History Channel or Discovery Channel has had a program on production of OSB. I don't recall specifically how the glue application occurs, but I suspect all the pieces are treated with the adhesive and then "oriented", which occurs as the chips drop through rollers that are arranged to alter how they land as the mat is formed, before being placed into a press where heat and pressure activate the glue. If I recall correctly, the system is at least two sheets wide until cut, and of course, sheet #2 in a row goes immediately on top of sheet #1, and they stay in that stacking while bound up and shipped. I'll bet the matching you observed occurs regularly where most of the handling up till installation is done by forklift.

Re: Sort of Interesting OSB Observation?

#3

On another note, Have you tried Solar Board?

Keith Newton

>When you said, "I have no idea how they make Oriented Strand Board. I assume it was one piece at a time", I thought you meant one chip at a time. Ha

To anyone needing to use OSB, if you have not tried the Solar Board, which is osb with a foil face, it is worth the extra few bucks. If you know anything about physics, you already know that black object will absorb light, and then radiate that heat, while white or even better a mirror type finish will Not radiate the heat trying to pass through it.

So when you use it for a roof deck, especially with a dark roof, the heat in the attic will be greatly reduced since that would be the normal means of heat transfer up there. It will pay for itself by money saved through energy savings soon.

Re: Sort of Interesting OSB Observation?

#4

Re: On another note, Have you tried Solar Board?

Stuart Hough

>You'll need tokeep an eye on the roof shingles. Depending where you live and the intensity/duration of direct sunlight, you might have problems with the asphalt shingles cooking from underneath, which is due from getting a double-dose of heat. My next door neighbor had that problem when I lived in Florida.

Re: Sort of Interesting OSB Observation?

#5

Re: On another note, Have you tried Solar Board?

Barry Irby

>I was thinking the same thing. I have not seen Solar board, but as a Home Inspector i have seen a few disasters as a result of "unintended consequences"

They make foil faced foam to be used as subsiding on the exterior walls. (several other foil faced products also.) If you install cedar or other knotty siding over the foil, it will cook it from the back side and the knots fall out. Gives the house a wonderful "twinkle" at night when the head lights hit it.

In the deep south part of Florida foil and vinyl wallpaper can be a disaster because they are vapor barriers and when the AC is on, condensation occurs under them and mold grows if you use organic glue.

The roofing industry originally would not give a guarantee on shingle installed on an insulated deck. (SIPs or Structural Insulated Panels come to mind.) I would really wonder about the effect of foil on the life of shingles. Might be great under slate or clay tile where heat is not an issue.

Interesting idea though.

Re: Sort of Interesting OSB Observation?

#6

Re: Sort of Interesting OSB Observation?

DizD

>Have been involved in an educational program where we tour forest products facilities and one we visit is an OSB mill with a continuous press. Mat of wood fiber about 4" thick goes in one end about 6' per second and comes out 7/16" board - any length. Interesting feature is the cutoff saw which cuts the board to length. Runs at an angle depending on speed of press so that the board is cut at a right angle. Like driving a boat across a river you have to aim upstream to come out at a point directly across from where you started.