Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Finishing time

Posts

Finishing time

#1

Finishing time

lee beeden

>Ok I have asked this question before, but more feed back would be great!!!!! Thank-you in advance.

Kitchen cabinets are finished, they will receive normal wear and tear

Butcher block counter top, will not be a direct food contact surface.

Butcher is birch, the rest of the kitchen is beautiful fir with spalted birch panels.

I'm looking for that warm oil finish look, but i have learned my lesson in the past, doesn't really work for kitchens.

So what do you think?

perhaps a coat of oil and then spray it with lacquer?

Just purchased a gravity fed spray gun($89) but will have to learn how to use it. I must admit the thought of letting loose on this project is a little scary!!

what about shellac and then a spray on water based finish?

How easy is the shellac to put on?

Any feed back will be very much appreciated

Lee


img

Re: Finishing time

#2

JL

Re: Finishing time

JL

>I don't know how well water based finishes would work in a kitchen. I have visions of water streaks after a time (unless you are a lot neater around the sink then I am!).

Re: Finishing time

#3

Re: Finishing time

John Pappas

>We have a counter top with wood edging. I originally used a water base finish on it. In time, the edging near the sink got gummy. I ended up scrapping it off and recoated with a poly.

Re: Finishing time

#4

Re: Finishing time

Mark Mandell - Gone Round In Jersey

>Fuhr # 355 Waterborne Acrylic Varnish

or General Finish's High Performance Polyurethane (waterborne)

or Enduro Industrial Enduro Clear Acrylic

All of these exceed the KCMA standard for finish coatings/

KCMA - Kitchen Cabinete Manfacturers Assn.

Fuhr you can get direct from the company. General Hi-Per and Enduro are sold by Jeff Jewitt at Homestead Finishing.

Re: Finishing time

#5

the choice is clear

Bill Tindal, E.TN

>If you can spray the best finish you can put on for a kitchen is conversion varnish. Read and follow the directions for using it, ie don't get creative with using it. Drift by your local cabinet shop and ask what they use and where to get it. Personally I use Sherwin William Kemvar post catalyzed material. It will be available at any S&W store which I find handy. It is now self sealing, again handy. By spraying the proper luster and film thickness the look of any finish can be replicated. A version of this material, Kemvar C, is used commercially to provide an "oiled"finish appearance. Thinning M in a delustered version achieves the same effect.

Practice spraying on something other than the finished cabinets. Use good lighting.

Re: Finishing time

#6

Re: Finishing time OIL

Glenn Madsen near San Francisco

>Those look really nice, Lee.

If you want an oil look, but lots of wear and tear resistance, then Waterlox has several of their finishes to consider. It's a brush and wipe process, and let it dry pretty completely between coats, but you get gym floor like durability, and a nice, warm finish.

Don't think I'd consider spraying it, though.

Re: Finishing time

#7

Re: the choice is clear

Moses Yoder in White Pigeon, MI

>The conversion varnish we use is available in different sheens; a 30 sheen is what we use as standard, if you went with a 20 sheen you would have more of an oil rubbed look. Definitely srpay a test piece, larger than a 6 x 6 block; a 12 x 16 gives a better sample.

Re: Finishing time

#8

Re: Finishing time

Robert W - aka nailshooter

>Those are some excellent finishes, especially the Fuhr and the Enduro. I have seen some really pretty finishing done with the Enduro, and a lot of refinishers either use it or the ML Campbell line.

Robert

Re: Finishing time

#9

Re: Enduro

Mark Mandell - Gone Round In Jersey

>I just finished a A&C sofa table in cherry with Enduro. Worked in the open garage. LOL walks out to see progress and says, "Whoa, how are you going to keep the bugs out of that stuff out here when it stays wet so long?" She blinked when I explained that it had been dry for about an hour, and I was getting ready to put on the next coat. Did get a couple of nubbies in the top surface, but otherwise I wouldn't have to do any rubout on the piece. Applied with a Walcom FZ and CA Bandit pot.

mm

Re: Finishing time

#10

Re: Finishing time

Paul Dwight

>Beautiful cabinets, Lee. I really like the look.

Conversion varnish is great on kitchen cabinets but requires that you be very meticulous in mixing and cleaning. It can be kind of intimidating. I personally would not recommend conversion varnish to someone completely new to spray finishing.

Nitrocellulose lacquer looks great but is not durable enough for kitchen cabinets, IMHO. Alcohol and household ammonia will soften lacquer. Heat will soften lacquer. Standing water will leave a water mark.

I like Mark's recommendations. I've sprayed both Fuhr 355/375 and General Finishes High Performance Poly and have been very happy with the results. Both products spray quite well and are good for folks who are learning to spray. Both are very durable. I think they look great. I haven't used the Enduro finish.

I wouldn't worry about using either the Fuhr or the GF Hi-Perf Poly around water. Both finishes cross-link as they cure and, once that process is complete, water doesn't affect the film.

I believe the Fuhr finish is available in a flat sheen, which might help you get the appearance you're looking for. GF Hi-Perf Poly is available in a satin sheen which is fairly low-luster but is certainly not flat -- I suppose it looks more like an oil-and-wax finish. I personally like the satin GF finish. There's just enough sheen to give it that soft-to-the-touch look, but not enough sheen that the finish fights with the wood for attention.

Since you're not looking to change the color of the wood much, I would probably start by spraying a coat of dewaxed shellac. Zinsser SealCoat is great for this purpose. You can add a drop or two of TransTint Amber Additive if the pale SealCoat doesn't give you quite enough color. The SealCoat sprays pretty well out of the can with guns set up for most clear wood finishes. If you use a thinner cut of shellac, though, you might need a smaller needle/nozzle set for your gun.

Once the shellac has dried, you can sand with 320 grit if needed -- VERY lightly, keeping in mind that a single sprayed coat of shellac leaves a very thin film -- and then start spraying your topcoats. You should probably figure on spraying three coats.

If you spray a low-sheen waterbased finish, you may find the flatteners in the finish dry on the tip of the gun and mess up the fan of atomized finish. I keep a small brush with soft bristles in a cup of water and when I stop spraying to shift the workpiece or whatever, I use the brush to quickly scrub the tip of the gun. It only takes a second and it avoids the frustration of discovering that the beautiful spray pattern you had five minutes ago has somehow disappeared.

I'd love to see those beautiful cabinets when the finish is complete. Please post pictures! -- Paul

Re: Finishing time

#11

Re: SealCoat / Shellac Warning

Mark Mandell - Gone Round In Jersey

>Paul,

I had a Target wb poly finish crack on me when applied over a sealing coat of dewaxed Garnet shellac. I contacted Jeff Jewitt and Target directly. I found out that a number of waterborne finishes are developing this problem when applied over shellac, especially, I'm told, SealCoat, that is applied too heavy or too far along in its shelf-life span. Jewitt and Weise (the Target Coatings owner) both said that most of the better waterbornes are now self-sealing and don't need the shellac, but if you do still use shellac as a barrier/sealing layer, mix it fresh at no more than 1-1/2lb cut and apply only a thin coat.

Thought you should know.

mm

Re: Finishing time

#12

Re: Finishing time

Jack

>Hi Lee

I'd suggest you use Target Coating's Ultima Spray Lacquer (USL) on the cabinets. We spray it in our shop quite a bit, particularly when we're having trouble with solvent based lacquer blushing. USL is plenty tough enough for kitchen and bathroom applications. You can also tint the lacquer with TransTint dye to get the look you're after. Good luck and show us a picture of the finished product.

Jack