Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

OT--Removing roofing tar

Posts

OT--Removing roofing tar

#1

OT--Removing roofing tar

Gary Evans Tallassee, TN

>Hi all,

I'm currently involved in flashing the end of the store roof where it butts up against the brick parapet. Over the years there has been a massive buildup of roofing tar trying to seal the joint. Now I'm cutting a groove in the brick with a diamond wheel in my 4" grinder and putting in step flashing the way it should have been done in the first place.

The diamond wheel will penetrate the tar (an inch thick in places,) but it makes an ungodly mess because it melts more than it cuts. I'm looking for a way to clear a path to the brick so that I'm not throwing molten tar off the blade of the grinder. For some reason that stuff is HOT!

I thought about using my heat gun to soften the tar and scrape it out of the way, but I hesitate to do something that might cause it to catch on fire. We just had one big fire next to the store building. I really don't want to catch the building on fire, too.

Also, I have about 60' to do, so a labor saving method would be preferred. I just need to clear a space through the tar about 1/2" wide so that I can get a relatively clear shot at the brick. I don't mind running the blade through a thin layer of the tar.

Any suggestions would be appreciated.

Gary

Re: OT--Removing roofing tar

#2

No suggestions, only sympathy :-(

Joe Pack

>

Re: OT--Removing roofing tar

#3

Re: OT--Removing roofing tar

Barry Irby

>I think the "usual" method is to use a spud. A long metal bar with a flattened end on it. Basically a giant chisel. Used in the standing position. Sort a spear or a pike. Huge work.

Check with a local commercial tar and gravel roofer.

Might be better to do it during cold weather or at least he cooler part of the day.

Wonder if freezing it with dry ice would work?

Re: OT--Removing roofing tar

#4

Re: OT--Removing roofing tar

Bill Tindal, E.TN

>I would use a torch and scraping and have a hose handy.

Re: OT--Removing roofing tar

#5

Dale Lenz

Re: OT--Removing roofing tar

Dale Lenz

>Hi Gary,

Never have done what you are trying to accomplish so if you follow my thoughts please go with caution. How about trying to heat the metal tool blade up you are trying to use as a scraper/putty knife. Good luck,

Dale

Re: OT--Removing roofing tar

#6

Re: OT--Removing roofing tar

Robert W - aka nailshooter

>Gary - when we reflash a chimney, we take a beater chisel and knock off as much as we need to with a chisel and hammer. An average chimney of 6X3 gives about 18 lf of this to do, so about 1/3 of your total. This can be done anywhere from one to two hours.

If the tar is solid, holding well and is too much to get off, then I simply bend a taller flashing. So if the guys before you tarred up about 6 - 8", bend up your base flashing to about 10" to get you over all the old crap. That way you only chisel off the lumps.

Be careful when removing the tar. If the flashing was sealed properly to begin with, you may find that good commercial caulk is holding well underneath all that tar. It can pull chunks out of bricks and mortar very easily. That's why we use an old wood chisel.

Start in the morning when it is cool as possible and you might have better luck chipping and cutting that stuff off before it starts to warm up and get soft.

Robert

Re: OT--Removing roofing tar

#7

Re: OT--Removing roofing tar

Gary Evans Tallassee, TN

>Thanks for the input, everybody.

Taller flashing would work for part of the run, but the roof approaches the top of the parapet for a good portion. Also, I'm a little leery about trying to knock the tar off. The bricks and mortar are in pretty bad shape on the 3' I've worked so far. Plus, this flashing was free and I'm still working on a budget.

I guess I'll try the heat gun or torch and see if I can soften it enough to get it out of my way.

Thanks all.

Gary

Re: OT--Removing roofing tar

#8

Re: OT--I'd worry

Glenn Madsen near San Francisco

>about the bad bricks and mortar, and not let things go too long in that regard. Leaking water is one problem. Falling bricks is entirely another. JMO

Re: OT--Removing roofing tar

#9

Re: OT--I'd worry

Gary Evans Tallassee, TN

>Absolutely, Glen,

As soon as I can get the leaks fixed on the roof, repointing the bricks on the parapet becomes the priority. I'll have to repair some as I go along with the flashing.

Gary

Re: OT--Removing roofing tar

#10

Indeed .......

Scott in Eastern Iowa

>.......spudding it off is the preferred method used by most roofers.

Colder temps will usually make the roof cement chip off in lieu of melting off as it is likely doing now, unless theres lots of it then your sol.

Like thick butter is it?

If this can wait till a below zero day it will likely chip right off.

Im guessing you cannot Gary, so you have a big chore ahead of you.

Use a margin trowel to scrape the majority off the side of the brick, grab some nitrile gloves and scrub the area with white gas to remove even more of the *schmuck*. Cotton rags, old t shirts or old pants will be best ....and lots of them.

A call to a local roofer will likely result in them asking where its at and can they come take a look to quote it. You might get lucky and they may steer you better...but dont hold your breath.

lighter fluid will clean it off your hands, as well as gojo too.

No matter what you do and however careful you are....you will be taking some of it home with you. It will likely be in a discreet area, so beware.....damhikt.

For the flashing use vulcum brand caulk...I recall it being used heavily in the roofing industry, especially for use on concrete/brick to metal surfaces.

Good luck...I dont envy the work!

Scott

*pro comm. roofer of days long ago.......*

Re: OT--Removing roofing tar

#11

How tall is this parapetted area?

Scott in Eastern Iowa

>Another idea that just hit me would be to get some EPDM roofing material and glue the entire wall area, thereby leaving the schmuck and bad bricks in place? It would certainly look alot better, but you may need a helper to fit large pieces of rubber in place.

Tuck it up under the parapet cap and tie it in where the wall flashing meets the flat roof.

This would aleaveate you torching, scraping, cutting and installing any metal.

Re: OT--Removing roofing tar

#12

Re: How tall is this parapetted area?

Gary Camp Bend, Oregon

>I believe that Tar and EPDM do not get along well. If I have to make a temp. repair on any of the roofs at work that are EPDM, it has to be a rubber caulk, NOT tar.

glc

Re: OT--Removing roofing tar

#13

Another question

Gary Evans Tallassee, TN

>Good thinking Scott, but like Gary says, I have an incompatibility issue as I would be trying to glue the rubber to an asphalt roofing material. The problem I'm trying to resolve is that there is no metal flashing at the joint between the asphalt sheeting on the roof and the bricks of the parapet.

The tar that I'm trying to remove is pretty hard till I heat it up with my diamond wheel, then it goes all over the place, including all over me. I may try a little more chiseling to see what happens. I hate to beat on it too much, though, due to the condition of the brick and mortar of the parapet.

The problem comes from the fact that the tar is so thick, up to an inch in places. I know the roofing material has been renewed a couple of times over the years and it looks like they've tried to repair this joint at least that many times by laying down some kind of fiber material and coating it with tar.

I do appreciate all the input and particularly the sympathy. Any other ideas would be welcome.

I just had a thought, since I'm working with flashing that is a little too short to get above the level of the tar, I might lay a piece in at the roof level with roofing cement and then overlap it with another piece that would get me above the tar level, at least on a majority of the run. The upper piece would be cemented to the lower one. Anybody ever "shingled" their flashing?

Thanks,

Gary