Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

hardwood deck joints

Posts

hardwood deck joints

#1

hardwood deck joints

George Hresko

>I am new to this site and looking for advice on two aspects of installing brazilian hardwood decking. I am using 5/4 5.5 inch wide random length decking, and EbTy hidden fasteners. First question, if I use a biscuit joiner, on end butt joints, should the joint still be made over a joist / support member? Second question, we are laying the decking in a 90 degree pattern. That is the deck is L shaped and the decking is running parallel to each side of the deck. What is the best way to make the joint where the boards meet at 90 degrees? I have put in a doubled 45 degree support, however, with the normal twisting of the boards, the two that meet at 90 degrees may not lay flat. I am thinking of using a biscuit jointer, cuttting into the end of the board, and using an EbTy to join the two boards. Is this sufficient? Should I be face screwing instead? Final question; several places recommend using an adhesive between the decking and the supports before using the fasteners / screws. Do you have experience in this area, what do you think? I am concerned that using the adhesive is pretty much a one way solution, and if I would have to take something up, I will need to destroy the 'new' decking. Many thanks.

Re: hardwood deck joints

#2

Re: hardwood deck joints--kinda long winded

Wayne Allen, Carson City, NV

>Hi George -- I used the same exact size of this wood on my deck and also the EBTY fasteners. Here are some things that you should know before you put yours in. First and foremost-- without fail, if you use the EBTY fasteners make absolutely sure that the wood has a dry moisture content. The wood that comes from the supplier is most probably GREEN and very wet. If you put it down using the EBTY fasteners when it has high moisture content, it will shrink when it dries. DAMHIKT If you use the standard EBTY 1/8" spacing between boards and the wood is green, guess what-- your spacing between boards will grow after it dries. As a result, the spacing will no longer be that nice even look. The gap size may vary anywhere between 1/8" to 1/2" or more. It may even grow so much that the EBTY fasteners will no longer fit into the biscuit slots after the wood dries. This is a REAL problem. With all that said, using this wood gives a great look and minimum maintenance and it is VERY fire resistant. It is best if the end butt joints are done over a joist using a fastener, but I guess you could use a fastener on the ends if you happen to come across the situation where you can't use a joist support. I used 24" joist spacing and have no problem with the 5/4 wood. It is very hard and very stiff and does not flex. The only face screwing was done where the boards come together at the house and again at the outer edge of the deck. I predrilled and countersunk holes with plugs to cover the screws. I did not use adhesive. As a side note, it was a good thing that I didn't, because after the forest fire we had here a few years ago, there were a few "charred" boards on my deck that had to be replaced. It was no big deal. By the way, because the deck did not burn, my house did not burn. All of my neighbors lost their homes as a result of redwood decks and combustible home siding. We were the only house standing after the fire. This wood is good stuff. One other thing, the EBTY fasteners are VERY labor intensive and also quite expensive to buy. There are other hidden fasteners that you might also consider. They are long strips of metal angle with predrilled holes that attach to the joist and attach to the deck boards underneath. If I had to do it over again, I would probably use these fasteners. They are much cheaper to buy and much easier to install. The finished look from above is the same. -- Wayne

Re: hardwood deck joints

#3

Re: hardwood deck joints--kinda long winded

George Hresko

>Wayne-

Thanks for the note. I already have the EbTy's so I am committed there. As for the shrinkage, I appreciate your comments. I do not know how long the wood takes to come to equilibrium with ambient moisture. I see you are in a warm and relatively dry climate, while I am in the CO mountains, so there probably is some difference. I also noted on the wood that was delivered that there is a difference in the coloration of the wood where it was stacked, so I am guessing that it has been sitting in a sunny location somewhere for sometime.

Did you use adhesive? Did you use a 90 degree corner join like I am considering? Face screwing with countersinking and plugs seems to me to be counter to using a long life hardwood?

Again, thank you for your help. I appreciate it very much.

Re: hardwood deck joints

#4

Re: hardwood deck joints--kinda long winded

Wayne Allen, Carson City, NV

>George -- I can't warn you enough about the shrinkage of the boards and using the EBTY fasteners, don't ignore this. I did not use adhesive on the boards. When using EBTY fasteners, you will have to either use screws from the top or below on the first course of deck boards because of the clearance of any adjacent wall structure next to the deck. I had no problems with splitting and the plugs are virtually invisible. I did not use any 90 degree corners, but I don't see any reason why that would not work. I would put a fastener on each end grain joint. -- Wayne

Re: hardwood deck joints

#5

Re: hardwood deck joints--kinda long winded

George Hresko

>Wayne-

Thank you again for your advice. I have taken it on board and will bear it in mind as I make my work plan.

Have a great weekend!