Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Recommendations on dado blades

Posts

Recommendations on dado blades

#1

Recommendations on dado blades

Stephen Kirk in Quakertown, PA

>I have an old Crafstman wobble dado that I'd like to replace. I like the Freud Super 8" Dado blade, and I also expect the Forrest to be perfect (but expensive). Timberline has a cheaper set, but I wonder if you get what you pay for. I don't want to have to upgrade to a better dado set anytime in the near future. Anyone have opinions on what set they like?

Re: Recommendations on dado blades

#2

Hard to go wrong with a Freud blade.

Rod Peterson -- Ormond Beach

>I don't think you can ever go wrong with a Freud blade. They have three dado sets�the high dollar one is a fine adjust similar to a wobble, but it is most definitely not a wobble. I know little about it although I think it takes a little extra length on the arbor for full width. The second one, at around a buck eighty (I think) is the Super Dado you mentioned. The third one, and the one I have, is around $80-90�I don't know if it has a name.

Mine is perfectly adequate for the kind of work I do or anticipate doing, and it sounds like you might be in that same mode. It's not so much to spend that you would take a huge hit if you decided to sell it later to upgrade to the Super (or some other brand), and it may wind up being your dado-for-life.

Rod

Re: Recommendations on dado blades

#3

Re: Freud SD208

Chuck Lenz

>The Freud SD208 is a BIG improvement over the Craftsman Excalibur wobble blade that I use to own.

Re: Recommendations on dado blades

#4

You're going to laugh at me but.......

Basil

>....I have gotten some good dado's out of a $19.95 Harborfreight stack dado that was on special.

I needed some dado's for some shelves, nothing fancy. Didn't want to spend the bucks for a good one and run the wood I had over it. Buddy of mine talked me into buying a carbide stack dado they had at harbor freight. They were usually $29.95 and were marked down that day to $19.95. Bought it and thought "Well I'll use it for this and throw it away".

I made a zero clearence throat plate for it and to my surprise, it did a good job. I've used it since for making quite a few dado's. The corners were square , the sides straight and with the zero throat plate, no tear out on plywood. The only problem is the 'bottom' of the dado cut isn't perfect, leaves some ridges. I use some paper shims along with the brass ones to get it shimmed out for a perfect tight fit.

Re: Recommendations on dado blades

#5

I have a Freud and that is why

Ray Thompson - Middletown, IN

>I no longer do dadoes on the table saw. All of my dadoes are done with a router. Faster setup and more accurate, a fine trade off.

Ray

Re: Recommendations on dado blades

#6

Re: Recommendations on dado blades

Patrick Schupbach

>What about Infinity`s Dadonator? It has recieved excellent reviews.I use their ripping blades,and really like the way they perform.

Re: Recommendations on dado blades

#7

This is the one I have, Stephen

George@Colonel's Workshop-Havertown PA

>Good Morning Stephen

Its been used for several years. I have no complaints. Grooves are flat and smooth.

George

Re: Recommendations on dado blades

#8

Forrest...

Brian in Sandusky, OH

>...is the only dado that I have experience with.

It's more expensive, but I feel it is worth it.

I've had it for four years, and use it frequently. I had it send out for one sharpening in that time.

Cutting melamine is smooth, same with crossgrain veneered plywood, I haven't found a material that chips out with this blade.

There may be others that have come out since the four years that I bought the Forrest (my understanding is that Freud has wonderful offerings, as others mentioned), but I'm VERY happy with my Forrest.

Re: Recommendations on dado blades

#9

Freud SD608

Jim Shaver - Oakville, Ontario

>I have the Freud SD608,

It's the dial dado that they sell, not a wobble. I love it! No shims and each click on teh hub is 0.002", making work in 11MM and 17MM ply really easy to adjust to,

Take care,

Jim

Re: Recommendations on dado blades

#10

Re: You're going to laugh at me but.......

john lucas

>I have the same HF dado. Got it too cheap to pass up. The bottom of the cut is really ragged but the sides are OK. I'm saving for a better one will probably look at the Freud.

Re: Recommendations on dado blades

#11

Re: Recommendations on dado blades

Binen

>I have and use 2 different dado sets. First is a cheap Vermont American 6� set I use when making picnic tables or anything using construction grade materials. The other a Forrest 8� set which I use for everything else. Not sure of the price difference between Forrest and Freud anymore. I would guess the top of the line Freud to be about $75 cheaper.

Seriously think about how many dados you will be cutting and in what materials. If you plan to make a lot of cross grain dados in plywood I wouldn�t have anything but a Forrest. If however most of you dados will be in solid woods and hidden joints then save some money. I made the decision to buy a Forrest set and have never once regretted spending the extra cash. My cross grain dados are as crisp and chip free today as they were 6 years ago when I bought the set.

Binen

Re: Recommendations on dado blades

#12

Dale Lenz

Re: I second the Forrest

Dale Lenz

>

Re: Recommendations on dado blades

#13

Re: Recommendations on dado blades

J D Thomas

>I have this Infinity set, and also an 8" Forrest, which I've had for about 10 years. It needs to go back for sharpening, and since using the Dadonator, I haven't been in any hurry to send off the Forrest. It's an excellent dado set.

J D Thomas

ThomaStudios

Re: Recommendations on dado blades

#14

Use a router

Pat Evans

>

Re: Recommendations on dado blades

#15

Re: I third the Forrest. . .

Ted Wong

>and as a cheaper set that I had before the forrest the Dewalt did a pretty good job for $100.00 set.

Re: Recommendations on dado blades

#16

I have owned SD208 & SD508

Bartee (metro Atlanta)

>If you can spend the money for any dado that has 4 chippers instead of 2.

I had the SD208 with 2 chippers on each blade. The SD508 is just much, much better.

There was recently a thread on another forum about the same subject. I think that guy found like a Dewalt for $150 with 4 chippers on each blade.

My SD508 just does what is supposed to do, with very flat bottom dados.

Re: Recommendations on dado blades

#18

Re: Use a router pat knows!

albertabob

>

Re: Recommendations on dado blades

#19

I got a systematic on sale years ago...

John in New Mexico

>and never had a complaint with it. I'd say a set that comes with shims is a must have... either that or make sure you buy an aftermarket set.

John

Re: Recommendations on dado blades

#20

Re: Recommendations on dado blades *LINK*

knotscott

>I owned the Freud SD208 set for ~ 4 years and was pleased with it. Last summer I replaced it with a DeWalt DW7670 that has twice as many teeth and a design more similar to the Forrest...so far I'd have to say that it makes a cleaner cut. It also has a nicer carrying case, nicer shim stock, and an additional chipper that the 208 did not have.

The DW set is also available as the H7200 and the Delta 35-7670.


img

DW7670 review on epinions