Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Sanding after seal coat?

Posts

Sanding after seal coat?

#1

Sanding after seal coat?

Stephen Kirk in Quakertown PA

>I'm getting ready to start wiping on poly onto some spalted maple that I just put a 3:1 cut of shellac on. After the shellac went on, everything is a bit fuzzy. Normally I'd sand this back down smooth, but I've heard recently that this isn't always necessary and that after several coats of poly, it will smooth itself out. I'm also worried about sanding right back through the shellac. I used the shellac because in some tests I noticed that even straight poly looked a little blurry and blotchy, but over the shellac, the grain was nice and crisp.

Any opinions?

Re: Sanding after seal coat?

#2

Re: Sanding after seal coat?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Stephen,

Knock down the fuzz with 320 and tack cloth.

George

Re: Sanding after seal coat?

#3

Sounds Like Someone

Mark Mandell - Gone Round In Jersey

>Doesn't understand poly finishes. Poly (especially oil-based) goes on pretty thick and can give the impression that it will fill grain and scratches. However, give it a month or two and it "pulls down" onto the surface as part of the curing process. What might have started out as a 6-7 mil newly dry coating winds up as a 2-3 mil cured film that telegraphs any surface defects.

Sand your fuzzies and nubbies off and vacuum clean very well. If you've gone through the shellac in a spot or two, pad on a bit more to reseal, and lightly sand to level any stroke marks. Let dry for at least 24 hours to make sure that all but an extremely minimal amount of solvent has evaporated.

BTW, I'm spoken to several waterborne finish makers and marketers (Target and Jewitt), and they report that they're having problems with cracking waterborne topcoats applied over shellac sealer, especially Zinsser's SealCoat, if the sealer has some age or is too thick. If you're using SealCoat, check the born-on date on the can. If you're mixing your own, make up a fresh batch for this application and run it through a coffee filter to catch any residual wax content that can impair adhesion. Also keep your sealer coat as thin as possible. If, like me, you use shellac to tint and match up variations in color of sections of a piece, consider adding tints to your sealer.

Re: Sanding after seal coat?

#4

Re: Sanding after seal coat?

Clint Searl, at the base of Haycock Mtn

>Flood with alcohol to wash of as much of the shellac as possible. Sand to 220. Proceed with multiple applications of the top coat for the desired build.

"Sealer" is unnecessary and irrelevant. JMO

Clint

Re: Sanding after seal coat?

#5

Re: Sanding after seal coat?

Steve Schoene

>It's not clear what kind of shellac you are using, and it makes a difference. The standard Zinsser Amber and Clear shellacs, which are three pound cut (meaning three pounds of solid in 1 gallon of alcohol) both contain wax, that might prevent polyurethane varnish from adhering very well. The particular Zinsser product called Seal Coat is 2 lb. cut shellac that has had the natural wax removed. A coat or two of this shouldn't cause a problem with polyurethane bonding to it, though it is wise to scuff sand before the poly.

While there might be a very small appearance difference with shellac as a first coat, polyurethane varnish doesn't need a sealer. You only need a shellac seal or barrier coat if there is a specific reason to keep two other products apart.

Re: Sanding after seal coat?

#6

several questions

Bill Tindal, E.TN

>Why are you using shellac under the varnish and why do you indicate it will be several coats of varnish? I don't put but 3 coats on a floor.

Most coatings now days can (if not should) be used as their own "sealer" coat. I have no experience with the water based varnishes but for oil based varnishes thin the first coat something between 1:3 and 1:4. It should flow easily and wick into pores. When it is hard enough to sand, sand with about 320 grit stearated paper (has white stuff on it) , blow off the dust, tack and apply the second coat. If the varnish does not flow smoothly I thin the second coat, but some less than the first. In hot weather one can sand after one day. The result will be a glass smooth finish.

Back in the old days varnish was a gummy material that didn't sand well. Hence, it was essential to apply a sealer coat of something that could be sanded. The sealer coat fixed damaged (sanded) wood fibers so that they stood up and could be sanded smooth. For a variety of reasons today's varnishes are typically hard and easy to sand after cured. Hence, they can be their own sealer.

Re: Sanding after seal coat?

#7

Re: several questions

Stephen Kirk in Quakertown, PA

>I use the seal coat to even out the stain. When I tried staining without a sealer, it turned out very blotchy. With the sealer, nice and even. I use Minwax wiping poly, then, and since it goes on rather thin I generally build up 4-5 coats depending on look.