Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

WAY OT: I need a countdown counter/motor shutoff

Posts

WAY OT: I need a countdown counter/motor shutoff

#1

WAY OT: I need a countdown counter/motor shutoff

Kneale Brownson in Northern MI

>With the wide range of experience on this wonderful resource, I'm hoping to get some motor control help. Part of the support for my woodgnawing activities comes from our production knitting business using machines that the manufacturer of has ceased business. The electro/mechanical devices that shut off the knitting machine motors when enough rows have been knitted are failing on us and there's no way to get parts to fix them.

So I need a way to shut off a 110-volt motor after a yarn carriage has made so many thousand passes back and forth along the knitting machine. So far, all the folks I could find who make counting devices do not have a way for those counters to control power to the motor.

What we need is a counter--it could be mechanical with a flip lever to count each pass of the carriage or it could be a magnetic reader of some sort--that can be set to shut off a power source after up to several thousand rows. We need to be able to plug the cord of the motor into the power source the counter would shut off.

Any suggestions?

Re: WAY OT: I need a countdown counter/motor shutoff

#2

Any chance you can post a pic of the counter?

Eddie Pacheco, San Jose, Ca.

>This would help a bit. Would a shut off at a prescribed length work?

Re: WAY OT: I need a countdown counter/motor shutoff

#3

After upteen years on the internet a

Ray Thompson - Middletown,IN

>question about something I may know a little about.

My first inclination is an optical sensor through a counting circuit connected to a solenoid that drops power to the motor. As I write this lint may be a maintenance problem but there are many ways to do the same thing.

Ray

Re: WAY OT: I need a countdown counter/motor shutoff

#4

Re: Any chance you can post a pic of the counter?

Kneale Brownson in Northern MI

>Here's a quick image I stole from Ebay of a similar machine to what we use. The device in the middle of the beds of needles with the little red knobs is the counter we need to replace. It has wires that go to the motor controls in the white box at the far right of the assembly and as the yarn carriage goes back and forth, a fixture on the back flips a lever on the counter. When the counter, which can be preset up to 9999 rows, reaches zero, it uses a microswitch to signal the motor to stop. I don't know exactly how the microswitch works, but it plugs into an electronics control board that's part of the motor. We don't want to reengineer the entire counter to use the current setup. We want a counter that will use a relay or something to shut off power to a 110-volt receptacle into which we can plug the motor's power cord. I'll get a better pix of the counter tomorrow if that would help


img

Re: WAY OT: I need a countdown counter/motor shutoff

#5

Re: After upteen years on the internet a

Kneale Brownson in Northern MI

>Right, Ray, an optical sensor, a magnetic sensor or something similar afixed to a point along the machine that can read something attached to the yarn carriage and then shut off the power when a preset number of passes occur. That's the kind of thing we need.

Re: WAY OT: I need a countdown counter/motor shutoff

#6

Try eBay?

Mark Goodall - ATL - tooljunkie

>Last year when I was buying Linear Bearings from vendors at eBay, I'm sure I saw something like you described. There are hundreds of eBay vendors who take apart industrial equipment and sell the bearings, rods, rails, and all the various components.

Give a look at McMaster website to get some ideas of the parts you need, as well as look though eBay. You might find what you need there.

Happy Woodworking!

Re: WAY OT: I need a countdown counter/motor shutoff

#7

How about replacing the circuit with a

Ray Thompson - Middletown,IN

>small PLC. At least you could maintain them for many years. We used Modicon but there are several, even one that is a card that you put into a computer that makes it a PLC. (Programmable Logic Controller) Should be straight forward for an electrical guy.

Ray

Re: WAY OT: I need a countdown counter/motor shutoff

#8

Re: Any chance you can post a pic of the counter?

Bob Entwisle in NJ

>Is shutting the power down to the motor enough, or does it need to 'STOP' i.e.' apply a braking force?

If simply shutting the power off is enough, then a simple PLC should do the job, I'm guessing there is already a 'turns' transducer available on the machine somewhere and that its output could be provided to the PLC, which can then be set to run for x turns and then stop. Check out McMaster Carr's web site http://www.mcmaster.com/

Type 'counter' into the find product window and see if there isn't something in there to do the job for you.

Re: WAY OT: I need a countdown counter/motor shutoff

#9

Re: Any chance you can post a pic of the counter?

Kneale Brownson in Northern MI

>Shutting off the power to the motor would work fine for us.

You are correct, there is a mechanical slider mechanism inside the motor controls box which stops the motor's travel in one direction and reverses it to the other. That function is independent of the row counter system and works fine with just power provided to the motor.

Can you tell me what "PLC" means?

Re: WAY OT: I need a countdown counter/motor shutoff

#10

Re: How about replacing the circuit with a

Kneale Brownson in Northern MI

>How is a programmable logic controller programmed? Can they be a self-contained device with individual inputs as far as setting the number of events to control (passes of the yarn carriage past a sensor)? We run six of these machines at a time, and couldn't be having to employ a computer in the setting of rows needed.

Re: WAY OT: I need a countdown counter/motor shutoff

#11

Re: Long reply.

Larry Clinton At Frankfort (Central)., Indiana

>I used many of these in the machines where I worked (Emerson) as an Engineer. Both types are widely available. Leeds, Veeder-Root and Durant are large manufactures of both styles. Not sure how your "yarn carriage" is sent back and forth - if it is a pure mechanical movement you will have to use either a mechanical actuator or magnetic or optical pickup to trigger the count cycle. If it has a solenoid or other electrical device that is actuated to move the carriage, you can use that signal to increment the counter. As suggested a micro PLC could also be used - but if you have not programmed one before - there is a learning curve and the programming device alone will probably exceed the cost of a pre-set countdown timer, pickup sensor and relay. The electronic counters with an optical (photoelectric eye) or magnetic pickup both have extremely long lives (5 to 10 years in 24 / 7 applications), where as the mechanical has a shorter cycle life due to mechanical wear. I would suggest you use a proximity switch if you can locate a piece of metal that will move to actuate it. (The metal should move within a 1/4 inch of the face (preferably) to "count" then move clear - no other metal should be within an inch or so from the face when not counting. A photo eye will also work - but I can envision some problems with keeping it clean in your application, even with an modulated infra red sensor. I would use a relay for the motor control. You can buy a counter with 120 - 240 vac operation, with a switch output that opens or closes when the pre-set count is reached. That can open or close a relay. I would use a plug in relay with the appropriate current carrying capacity for your machine motor. McMaster Carr & Grainger both carry the relays and sockets. Here is a link to the Veeder-root counter site that has a lot of easy to understand information about the various types of counters and their applications. If you need more help feel free to contact me. http://www.veeder-rootcounters.com/content.aspx?id=45

Re: WAY OT: I need a countdown counter/motor shutoff

#12

Re: Long reply.

Kneale Brownson in Northern MI

>Thanks, Larry, and everyone else. The yarn carriage is connected to a belt that the motor drives back and forth by changing motor direction at the end of each pass. All of that works independent of the counter. The purpose of the counter is to stop the motor once the desired number of rows has been knitted.

The original counter has a lever that gets flipped by a hoop attached to the yarn carriage. We easily could mount some other counter activation material, such as the piece of metal you describe, in place of the hoop. We could mount the pickup you describe similarly to the way the original counter is mounted, centered on the rail that the belt moves inside. I'll try our local Grainger again. When I went there yesterday, the clerk called their technical center and the tech said Grainger had no product that would do what I wanted???? I'll ask specifically for a PLC application.

Re: WAY OT: I need a countdown counter/motor shutoff

#13

Re: How about replacing the circuit with a

Ray Thompson - Middletown,IN

>A good industrial electrician would be able to set up and program a PLC for you. Go to McMaster-Carr and do a search for "PLC" you should be able to get one for your application for $200-400. Not exactly cheap but reliable and relatively easy once you get through the learning curve. They can be programmed from a dedicated device (more $$) or from a PC with their software.

Ray

Re: WAY OT: I need a countdown counter/motor shutoff

#14

programable logic controler

Phil Joines Krum, Tx

>

Re: WAY OT: I need a countdown counter/motor shutoff

#15

While at McMaster search for

Ray Thompson - Middletown,IN

>proximity switch. They have a bit of info about them.

Ray

Re: WAY OT: I need a countdown counter/motor shutoff

#16

Re: Long reply.

Larry Clinton At Frankfort (Central)., Indiana

>Grainger doesn't carry a "prepackaged unit" that will do exactly what you want. However they should have all the components to make it. If you get the right person they should be able to sell you what you need. If you want to replace the existing mechanical counter, all you would need is a mechanical predetermining counter (with enough digits), a relay socket, a plug in relay sized to carry your motor current, an enclosure to house the relay (bud box), romax connectors (to connect the wires into the box) and a bit of extension cord large enough to carry the motor current.

Re: WAY OT: I need a countdown counter/motor shutoff

#17

Re: Long reply--options

Kneale Brownson in Northern MI

>Would someone else have a "package"?

I don't find a mechanical predetermining counter in Grainger's catalog.

Re: WAY OT: I need a countdown counter/motor shutoff

#18

Re: Long reply--options

Larry Clinton At Frankfort (Central)., Indiana

>Sorry Kneale, try this link to McMaster Carr http://www.mcmaster.com/

The timer # 1895T29 counts down from a preset number (max preset is 89,999 counts). You may be able to use this without a relay - as it will switch 10 amp at 220 Volt, but if you wish to extend the counter life it would be very simple to add a plug in relay to switch the load.

Re: WAY OT: I need a countdown counter/motor shutoff

#19

Re: Long reply--options

Kneale Brownson in Northern MI

>Thanks, Larry. That looks like it might do the job. Bit pricey though at $315.00 each. Since we'll eventually need at least half a dozen of these, as well as the switched power source, any suggestions for getting them cheaper?

Re: WAY OT: I need a countdown counter/motor shutoff

#20

Re: Long reply--options

Larry Clinton At Frankfort (Central)., Indiana

>Kneale, since your using that many - I would retract my statement about the PLC. A PLC (micro unit) will run 8 inputs and 8 outputs. Each input can be programmed as a counter - and each output can directly drive a relay to control the machine(s). (You could actually run different machines with 1 PLC.) Some of the Allen Bradley units have a keyboard built in (PICO units) that would allow you to select the counter you want to program and to set the number of counts. You can probably find a distributor in your area and have the unit installed and programed for less than the cost of the other options. they would also handle the relays and pickup sensors. Im not sure of the total cost as you will need someone to program and set up your system - think it would be cheaper (and a whole lot longer life) than replacing the existing counters. I doubt you will replace all the units for less than $2,000 any way you go unless you find surplus on Ebay. One thing about a PLC is that they have a very long life. As I said before mechanical counters have a limited life !0 million counts or so. The PlC does not. It should last years in your application. The only "wear" in the system would be the relays controlling the motors. These would last years and replacement would be plug in at less than $40 ea. Wish I was closer - might find a cheaper solution, and I could set up any plc (I retired after about 40 years as a manufacturing engineer.)