Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Angled finger joints?

Posts

Angled finger joints?

#1

Angled finger joints?

Scott in Douglassville, PA

>Hi, all -

I have a project coming up, which is akin to building a small box with long edges square and perpindicular to the bwhile the short edges angle out from the base by about 40�. Thinking about joinery, I'd kind of like to use finger joints, but am having a hard time viusalizing how to lay out and cut them on a bevel.

Anyone have suggestions? Or a better alternative?

Thanks,

Scott

Re: Angled finger joints?

#2

Re: Angled finger joints?

Scott in Douglassville, PA

>Ok, I think I have it - set the angle based on the bevel I cut on the end of the board. Use two blades from my dado set (which may be the first time it's been used since I hacked my fingers apart...). Make the finger joint jig with angled cuts instead of square. Make the tongue that sits in one slot, and hand plane the bevel onto it. Should work - give me finger joints that project straight into the joint instaed of at an angle.

Is that right, or is there a more idiot-proof way?

Re: Angled finger joints?

#3

Try looking for hopper joints.....

Barry Irby

>Years ago I remember seeing and article on making joints for wooden hoppers, basically square funnels. I have never done it, and it is a dim recollection, but maybe that will give you a place to start looking.

Re: Angled finger joints?

#4

Ellis Walentine

Is this what you're thinking?

Ellis Walentine

>Here's a drawing of what I hear you describing. If so, it won't be easy no matter how you do it. The tablesaw blade cuts a square-bottomed groove and every groove will have to be at a different height with the side pieces held perpendicular to the table. I imagine it could be done, but I've never attempted it.

If you don't have too many fingers, you might lay them out and cut and chisel them.

Ellis


Re: Angled finger joints?

#5

Re: Is this what you're thinking?

Scott in Douglassville, PA

>That's it exactly, Ellis. Thanks for the CAD - helps my visualizing.

I'm gonna ponder a while and see if I can't make it happen. Thinking it'll take a couple setups on the tablesaw, anyway. Cant the dado to the right to match the bevel angle and get one piece. Think the other is a compound bevel, so it'd require the same angle on the dado, but a matching angle on the miter square to make it work. Right?

Re: Angled finger joints?

#6

Doh - alternatives?

Scott in Douglassville, PA

>You're right on the square-bottomed cuts. That'd turn into a lot of chiseling. Might could do that; not sure if I want to.

Alternatives? Aside from compound bevel dovetails?

Re: Angled finger joints?

#7

Re: Is this what you're thinking?

Clay Foster

>This could be done on a table saw, but it would require filing the teeth of a saw blade all to the same angle equal to the angle of the drawer. You don't need a deep cut, so buy an 8" steel tooth plywood blade, tilt it the the angle you want, and file the teeth parallel to the table saw top. A plywood blade with lots of teeth will give less chipping on the exit side of the cut than say a 20 tooth combo blade.

You can also use a blade filed like this for cutting dovetails.

Re: Angled finger joints?

#8

Re: Is this what you're thinking?

Joanne Adler in Pt. Pleasant, PA

>Scott,

Some years ago I wanted to make a bowl for my mother. But I do not turn (nor own a lathe). I made this square "bowl" with finger joints. It took a trial or two, but I finally got them to work. I believe I cut the angles on the sides first and then used a boxjoint jig. If you wanted the joints to be of incremental heights, I guess you could cut them long on the straight edge and then cut the angle. They would be at a different angle to the end of the wood, in that case.


img

Re: Angled finger joints?

#9

Re: Another view 

Joanne Adler in Pt. Pleasant, PA

>


img

Re: Angled finger joints?

#10

Re: Angled finger joints?

Al Stokka - Cambridge, Iowa

>You could cut a rabbet, equal in width to the thickness of the adjoining part and one-hlf the material thickness) on both ends of each of the long sides. I've made a number of boxes using rabbet joints and they nearly disappear.

Al

Re: Angled finger joints?

#11

Re: Is this what you're thinking?

Loftguy

>Hi Joanne,

Beautiful work; I'm sure your Mom was quite pleased with the "square bowl".

Bob

Re: Angled finger joints?

#12

Re: Angled finger joints?

Scott in Douglassville, PA

>That may be what I end up doing. Then pin 'em or something.

Re: Angled finger joints?

#13

Re: Angled finger joints?

Marv

>Joanne's box looks pretty straight forward. Cut the angles on the sides and just work off those angles like you would any other dovetail with straight sides.

Joanne...that's very nice work!

Marv