Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

What's wrong with relying on plywood . . .

Posts

What's wrong with relying on plywood . . .

#1

What's wrong with relying on plywood . . .

Yonak

>. . . to keep cabinet doors flat ? I thought that's what engineered wood was all about .. dimensional and structural stability.

I've got a bunch of 1/2" cherry plywood which I'd like to use to make cabinet doors. My plan is to overlap and spline the rails and stiles to the plywood and interlock the corners. I'm told that plywood can't be trusted to stay flat and the doors are likely to warp. What's wrong with that picture ?

Re: What's wrong with relying on plywood . . .

#2

Re: What's wrong with relying on plywood . . .

Robin Corell in Atascadero, CA

>If you can not take what you have been told is not a good idea at its face value then I would strongly recomend reading Bruce Hoadley's book "understanding wood" it is an inexpensive educatuion tht will help you understand why pywood would not be suitable for cabinet doors. I guarentee reading this book will also make you a better wood worker.

Robin Corell

Re: What's wrong with relying on plywood . . .

#3

Re: What's wrong with relying on plywood . . .

Moses Yoder in White Pigeon, MI

>If the plywood is flat now there is a pretty good chance it will stay flat. But plywood still moves some so I would use it the same as a solid wood panel in a frame. Allow it to float in the frame. A veneered panel is essentially the same thing as a plywood panel, and has been used for a number of centuries although I can't recall when veneering started. But the panel has to be balanced so that the front and back will move at the same rate otherwise it will bow. Many kitchen cabinet companies, including the one I work for, occasionally use 1/4" plywood panels for cabinet doors. But the panel is grooved into the frame and made 3/8" smaller than the opening and space balls are inserted into the groove when assembling the door.

Re: What's wrong with relying on plywood . . .

#4

Ply Doors

Mark Mandell - Gone Round In Jersey

>I've used it for years for both doors and flat door panels with no problems. I usually make flat door panels out of 3/8" and 1/2" high grade veneer ply and, as mentioned, allow the panels to float in the frame. Very important to finish both sides evenly to keep the balance of moisture content on the face and back; and I pre-finish the panels before assembly into the frames. I've seen others use 1/4" for panels, but usually with bad results; I suspect not enough plys to stabilize the panels.

You can't use BORG Special plywood, however. Baltic, Appleply, or similar stock are only what I use and then veneer to match the other wood if necessary.

mm

Re: What's wrong with relying on plywood . . .

#5

Re: What's wrong with relying on plywood . . .

Joe in a Cleveland suburb

>I used 1/4" Cherry ply for my kitchen cabinet doors (in frame and panel) several years ago. Still flat. My only complaint is they are too light and have a cheap feel to them as a result. I wouldn't do it again only for that reason.

Joe

Re: What's wrong with relying on plywood . . .

#6

all plywood is not created equal

Bill Tindal, E.TN

>If it is wet during manufacturer, like some I got from Home Depot, it will warp severely upon drying. If it has but a few plys it will also warp in response to moisture changes during use. On the other hand, if it is a furniture grade of plywood it should stay flat.

Re: What's wrong with relying on plywood . . .

#7

Bingo!

Derek

>I agree!

LOTS of doors made with plywood and still flat. You MUST use good plywood for this to hold true.

You CAN glue the plywood into the frames if it is good plywood. It will not move much and the doors will be much more solid and strong.

I've made lots of drawers from 1/2" Russian birch plywood (cheap Baltic birch plywood). They are glued tight, including the bottoms. They hold water just fine (yes, they are finished). You can actually stand in them! They have been fine for years - no splits or warping.

1/2" plywood for the panels (rabbet the back side to get a 1/4" tongue to insert into the frame) will make a much more solid door and will feel better too.