Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

new woodworking club lessons

Posts

new woodworking club lessons

#1

new woodworking club lessons

john lucas

>I just got involved in a woodworking club that has started in our community. At present they have a meeting place but it's not in a shop so we don't have access to tools or a workbench. We have several people wanting to learn woodworking and several who are somewhat versed in general woodworking principals. I am mostly a woodturner but have done a little bit of everything else.

At their meetings they have mostly just discussed things with an occaisionl show and tell. I have volunteered to do some demo's but I'm not sure what to do without a workbench. What would you all suggest. I could bring something like a shopmate to use as a bench. I thought I might start with sharpening chisels and plane blades. Maybe a demo on tuning a handplane. I could bring my shaving horse and demo a drawknife and spokeshave. With the shopmate I could probably do some demos with the router. I could use it true up cross cuts and joint board. I could cut rabbits or some other type of joint to show them how to build a box.

The biggest problem is several of them don't have any tools so I don't want to scare them off. I don't want to tell them they need a $700 hand plane and $500 worth of japanese chisels and saws to start.

Re: new woodworking club lessons

#2

Re: new woodworking club lessons *LINK*

Joe Dusel (Vista, CA)

>Our woodworking club has mostly talks with props and some Powerpoint presentations for our general meetings, but we do have shop tours where we get some of the members to do some hands on show and tell. This might be something you might look into. At our last shop tour we had a local vendor give us a demo on welding bandsaw blades and tuning up bandsaws.

Joe


North County Woodworking Club in the news

Re: new woodworking club lessons

#3

Re: new woodworking club lessons

Mike Hamilton

>John,

Didn't one season of the Woodwright's Shop have a series of projects to build some necessities for doing woodworking? Or maybe it was one of St. Roy's books. A tote for small tools, a sawhorse, a bench top, the benchtop on the sawhorses to make the bench frame ......etc.

On the non-neanderthal side, Popular Woodworking for the last year or so has had a series of projects under the heading 'I Can Do That.' The projects are fairly straigthforward and can be done with a combination of hand tools and tailed apprentices no more complicated than a scrollsaw, router and ROS. Their website has a companion 'manual' that is a nicely done,downloadable pdf.

Just a couple ideas....

Regards,

Mike Hamilton

P{lainfield, IN

Re: new woodworking club lessons

#4

Re: new woodworking club lessons

john lucas

>Good idea Joe. Might be able to run video's if any of the members have some. Thanks.

Re: new woodworking club lessons

#5

Re: new woodworking club lessons

john lucas

>Thanks. I'll look through my Popular woodworking. I also have one or two Roy Underhill books.

Re: new woodworking club lessons

#6

Re: new woodworking club lessons

Tim Caley - North Little Rock

>Here is a link to the woodworking club I belong to. Some of our newsletters are online now. You can look at them at look at some of the programs that we have put on and maybe get some ideas.

Good luck with your new club. I sure enjoy mine.

Re: new woodworking club lessons

#7

Re: new woodworking club lessons

Barry Irby

>Seems to me you would want to start with some fundamentals. Just not sure fundamental what?

Safety? Always a good idea. Huge topic, pervasive.

How about measuring? Different types of rules and tapes. I have recently gotten a dial caliper that reads in 1/64ths and 1/100's I enjoy a lot. Discuss how accurate is accurate enough.

How about setting up a shop? What is the minimum you would need to start a shop? Personally I do everything with a tree branch I use to hit a sharp piece of metal I found in the road, but others may be able to afford power tools. I would get some if I just had power, whatever that is.

You could discuss various joints. Dovetails, M and T, half laps, butts, etc and where they are used and which are stronger.

A session on wood characteristics and how it moves would be good.

That session could lead into how to apply that to furniture design and its effects on design. Such as don't do cross grain connections or don't dovetail a wide solid piece to a piece of plywood.

A session on glues would be good. As in; don't use CA to glue your finger to your eyelid.

I could go on and on, but I already have.

Re: new woodworking club lessons

#8

Good ideas-Keep em coming I'm writing as fast as I

john lucas

>I think discussing some sort of workbench should be high on the list. You can't do much if you can't hold the work. I started with a piece of plywood that was hinged to the garage wall. It locked in the up position to form a cabinet to hold the tools I had. This was in an open garage so I had to protect what little I had from the neighborhood thief.

Re: new woodworking club lessons

#9

Re: new woodworking club lessons

Jesse in New Mexico

>One of the most popular talks at our club is "tuning a bandsaw". We run it about once a year and interest remains high. Jigs are also popular.

Re: new woodworking club lessons

#10

Re: woodworking club - safety

Joe Dusel (Vista, CA)

>Just don't do a safety meeting like ours. We had a hand surgeon do a talk with a graphic PowerPoint presentation. Oh man! That was hard to watch...

Joe

Re: new woodworking club lessons

#11

Re: new woodworking club lessons

john lucas

>I've got to tune my new bandsaw. I could take photos of the steps or I could tune it up and then have everyone over and walk them through the procedures.

Re: new woodworking club lessons

#12

Re: new woodworking club lessons

Barry Irby

>My Bandsaw came late to the shop. I had a RAS,TS, shaper, Jointer, Lathe, lunchbox planer, and a DP before I got the Bandsaw. It has not won a place in my affection. All my other tools perform as I expect them to. The bandsaw mocks me. What I am saying is it needs tuning up, perhaps with a bigger hammer. I bought the Dugenski book, but I think he must have put out two or more, because the one I got ain't so great. So a lesson on tuning one would be a good thing and perhaps saving it�s life as well.

PS, if I had known how much I was going to spend on up grades It would have been smarter to buy a bigger saw.

Re: new woodworking club lessons

#13

Re: Our club has a few years on it now

Glenn Madsen near San Francisco

>It's an adjunct or outgrowth of the adult ed program in the community. There's a busy shop there, but, for the last 18 months or so, we don't hold the club meetings in the shop. There's not nearly enough room.

And the meetings had been changing, too. For the last 5 or 6 years, they have been mostly slide shows and chalk talks from folks in the business, mostly the artistic end, and talking about design and construction. This after a 'what's going in the Special Interest Groups', and 'what's happening with the public service stuff', and a member show & tell. That usually takes most of an hour.

Many of our speakers have been published, or on television, or done something noteworthy. They are a good group, and we're happy to have them.

The parts about 'how to sharpen a handplane', and 'turning a rough-edged bowl' and 'toybuilding' are, for the most part, dealt with in the special interest groups. We teach one another, and bring in folks who can teach us, and work out the details on our projects together. And we take classes at the adult ed, when we can fit them into our schedules.

Best wishes with your program, and much success. There can be a lot of joy found in such an effort.

Re: new woodworking club lessons

#14

Dovetail-O-Rama

Virgil johnson

>One of the demos that I helped with at a club meeting was hand verses machine cut dovetails. My friend George demonstrated cutting a through dovetail by hand and I brought my Leigh jig to demonstrate.

Re: new woodworking club lessons

#15

Re: new woodworking club lessons

Jim Dillon

>John,

When I read your post, I thought of Peter Korn's book "Working with Wood" (Taunton Press). The chapters are arranged in a logical sequence, each building on the reading and skills described in the previous chapter. For example, the first chapter is about wood itself and wood movement, followed by joinery basics, woodworking machines, hand tools, sharpening, milling a board 4-square, cutting a mortise and tenon by hand, cutting dovetails, assembly and finishing, and finally a project building a small bench with handtools. A concluding project is a small, but nice cabinet with a drawer. The general subject of these chapters could be fleshed out by the more experienced members of your club, maybe with slides or actual demonstrations - at least with hand tools. And since you are experienced as a turner, perhaps turning knobs for the cabinet would be practical. And I think it is important to emphasize that there are usually several valid ways of doing the same thing - and to give a demonstration of each way if possible; using sandpaper or waterstones to sharpen a chisel comes to mind along these lines. Just some thoughts and I wish you well in your new endeavor.

Jim