Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

How I stain walnut

Posts

How I stain walnut

#1

How I stain walnut

Bill Tindal, E.TN

>This post is in response to some questions on staining walnut. I always stain walnut to keep it from bleaching. I use a pigmented oil stain. For years I used Sherwin Williams pigmented stain. Finally, I gave up because they reformulated every few years and I had to figure out a new color to order. Now I grind Lee Valley pigments in linseed oil. For walnut I use about half each of burnt umber and raw umber. Put the pigments in a mortar and pestle with linseed oil and grind away until thoroughly homogenized- 5 min or so.

I apply stain with a rag. Dip rag in stain and rub stain on until most of the stain is transfered from rag to wood and then repeat. My rag size just covered my index finger so were are talking about picking up a very small amount of stain each time. I expect to experiment with a shellac pad (a ball of wool in a rag) next time. When a surface covered by stained, wipe thoroughly with a clean rag. Be sure the pores get stain, best seen on low angle light. I only used about 5 mL of stain to do 10 sqft of drawer fronts.

People complain that stain "muddies" the appearance. I don't see this problem on a properly sanded surface. I sand walnut to 180 grit. When sanding with 180 there should be no dull spots. Dull spots mean the grain is roughed up and it is catching dust. Any place that catches sanding dust will catch stain and be blotchy. I suspect improper sanding is the cause of some objections to staining.

I always sand before staining, even if I have a perfectly hand planed surface. A planed surface has open pores and it will soak up stain like a sponge. I find it hard to control depth of staining on such a surface.

The picture is a drawer I stained yesterday. You can judge if it is blotchy or whether it has a muddy appearance and decide if you want to stain in the future or not.


img

Re: How I stain walnut

#2

Jim in Burlington Ont.

What a little teaser

Jim in Burlington On

>Bill,

That's quite a picture. Sure makes me want to build something out of walunt and try that method out. Plain oil wood porn that pic is. Might make nice computer screen walpaper.

Re: How I stain walnut

#3

Bart Goldberg

Re: How I stain walnut

Bart Goldberg

>Bill,

To be clear, you are referring to LV Earth Pigments, yes?

What are the actual amounts you mix together?

Thanks

Bart

Re: How I stain walnut

#4

Use a muller

Dean Lapinel

>Easier to use a muller and glass rather than a mortar/pestle.

Re: How I stain walnut

#5

Re: How I stain walnut

"RJ" Whelan

>Bill ... pretty nice.

I just finished a large built-in cabinet for some customers (five months of construction) - the face frame, door and drawer in-set panels were hickory and the moldings and door and drawer frames were walnut.

This piece was going into a house containing a lot of Italian antique furniture and reproductions and had to, more-or-less, fit into the existing decor.

I ended up making 11 samples before I arrived at a colour combination that please the decorator. The combination was so unusual (for me anyway - I almost never stain, unless the client insists) I thought I'd pass it along.

1. Make a dye-stain from ORANGE liquid Transtint (Rockler) mixed at 1oz concentrated dye to 32oz of laquer thinner. Apply to all planed and sanded surfaces. Rub out all surfaces with Scotchbrite to knock down the raised grain. The piece will be a horrid orange colour when you're done and will scare you to death thinking you've just destroyed all of the foregoing work.

2. Apply a coat of Minwax Dark Walnut stain - don't let it set for more than a couple of minutes. Rub with Scotchbrite to knock back minimal grain raising.

3. Apply multiple coats of Minwax wipe on poly - let the first coat sit for at least ten minutes before rubbing it as dry as possible. Subsequent coats only have to soak for a few minutes before wiping. I don't sand (600) until after the second coat of finish - this minimizes the chance of sanding through and getting into the stain and causing light spots.

The Orange dye imparts just a hint of red to both the hickory and walnut and brings the two very different material colours a bit closer together.

I'd never have believed this would look as good as it did - the decorator was thrilled the customer was so pleased they ordered a complete bedroom suite (bed, low dresser, tall dresser, (2) bedside tables and amoire) and is willing to wait ten months for completion.

rj

Re: How I stain walnut

#6

What's a muller?

Jesse in New Mexico

>

Re: How I stain walnut

#7

Re: How I stain walnut

Barry Irby

>Bill, How long have you been doing this? Your experience is that this works? I am skeptical that such a small amount of stain would have either the ability to block he UV and prevent fading or to impart enough color to offset the fading. Here's hoping you have the experience to back up what you are saying, because it looks great.

PS, Can I have that piece of wood?

Re: How I stain walnut

#8

a piece from 1958

Bill Tindal, E.TN

>Bill, How long have you been doing this? The plaque was made while I was in high school (Clinton , NY) in 1959 to mount a particularly fine set of antlers upon (which I took off for the PIC. They had shop class back then! The stain is some unknown pigment stain and the finish some unknown brand of varnish. This is the oldest piece I could find and remember. I have other walnut pieces from1970 forward and several rooms of walnut house trim, again from later dates.

Your experience is that this works? Duh!

I am skeptical that such a small amount of stain would have either the ability to block the UV and prevent fading..... It probably doesn't prevent fading of the wood. But if you use a mineral pigment the pigment will never fade.

....to impart enough color to offset the fading. There is the piece, you be the judge.

Here's hoping you have the experience to back up what you are saying, because it looks great. You will have to judge that too. I don't guarantee advice that is free.

PS, Can I have that piece of wood? Two years ago when we were in the business I would have been delighted to have sold it to you for $4.29/ bdft. This board is not anything special. Had I wanted to flaunt some wood I would have shown the curly top for the piece.

I think the two biggest mistakes people make staining is 1. Not sanding all the damaged grain away (it over absorbs stain and blotches) and 2. Flooding stain on the wood rather than wiping it on, again leading to loss of control.


img

Re: How I stain walnut

#9

I am Impressed! Thanks.

Barry Irby

>

Re: How I stain walnut

#10

Re: What's a muller? *LINK*

Dean Lapinel

>Muller is used to grind pigments with oil in a manner tha makes it easy to pick up and place in a tube.

Pic worth a thous words. see:


muller