Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Rebuildng Nail gun questions!

Posts

Rebuildng Nail gun questions!

#1

Rebuildng Nail gun questions!

Barry Irby

>I have a Senco Finish nailer (SFNII) that stopped functioning today. The driver is "up" (not visible if you open the chute where you clear a jamb.) The gun blows a small amount of air out of the exhaust and only makes a small thump when you pull the trigger. Probably time for a rebuild.

Anyone ever rebuilt their own? My understanding is that there are O rings to install. Where do I get the rebuild kit and how much should I expect to pay? Or should I just take it to the "shop"? Any other Ideas?

Re: Rebuildng Nail gun questions!

#2

Re: Rebuildng Nail gun questions!

Ron Hildreth, Alta, Iowa

>Barry,

A close friend of mine just rebuilt three of his guns, two roofing guns and a framing gun. He told me he would never rebuild them again, as one roofing and the framing gun worked only for a few hours after rebuilding them. He's done this many times before, so knows what he is doing. Problem was that parts were hard to find, and the total rebuild kit for the roofing nailer had cost him nearly $250, which was about $100 more than the last time! His guns are all pretty old sencos. It sounds like it's cheaper to toss and buy new!

Ron in Iowa

Re: Rebuildng Nail gun questions!

#3

Re: Rebuildng Nail gun questions!

jeff

>It all depends on age and cost.

A rebuild kit for my Bostitch was about $70 for a $200 nailer.

Another Bostitch cost $100 new, so $70 was way too much.

You might keep an eye out for Manufacturers demos. Bostitch offers a free tune-up when they have them at my local supplier.

They fixed one nailer for me for free about 2 years ago and all it needed was a new gasket, Still working fine.

Maybe Senco offers them.

Jeff

Re: Rebuildng Nail gun questions!

#4

Re: Rebuildng Nail gun questions!

Bruce Wrenn

>Barry, you will have to get a rebuild kit from a Senco distributor, or authorized dealer. Being oil-less they use a teflon type ring and piston liner. It is no big deal to rebuild one. I have done one of my three once. Dirt is their #1 enemy. Of course, on most any given day, one of the local pawn shops has one in stock for $75, less any discounts I can weasle out of them (usually between 15 and 25%)

Re: Rebuildng Nail gun questions!

#5

Rebuildng Nail gun

nailshooter

>Barry: Depending on the gun you have, you may be able to get repair parts over the net. As a contractor, I rebuild my guns as needed, and rarely have problems with them after a rebuild.

The thumping noise is probably due to a blown cylinder gasket. IF this is an oiled gun, this is an easy fix. With the right sized "o" ring (or rings) in hand, take the head off the gun. Turn it upside down and tap on the gun over a table until the piston falls out. You will be able to see the damage to the "o" rings on the cylinder immediately.

Remember, you CANNOT use regular lubricants on this and must use specially made lubrcants designed to work with the "o" rings without dissolving them. If the cylinder is clean, do not clean the inside. Do not shoot WD 40, Tri Flow, graphite, or any other lubricants in the cylinder or on the piston. Buy the correct gun oil at the tool store and use it on the "o" ring before reassembly.

My rebuild kits for my Bostitch guns are about $35 for soft parts. Drivers are about $75, and triggers are about $35. I buy those straight from Bostitch or on Ebay. Soft parts shouldn't bee too much for your oiled guns.

On my generic branded guns, I bought some neoprene washers in a 500 piece assortment pack at Harbor Freight and look like they will do the trick for them as they are shop guns only. So far, so good.

Robert

Re: Rebuildng Nail gun questions!

#6

Jammed Driver

Rick Christopherson

>You'd be amazed at how simple the cylinders are in these guns, but the fact that you are blowing air out of the exahust may be indicative of a bent or jammed driver that is not letting the piston return to the top. This may not require a full rebuild.