Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

A finishing question for the crowd...

Posts

A finishing question for the crowd...

#1

A finishing question for the crowd...

Glenn Madsen near San Francisco

>I'm impatient. That's bad for a woodworker, but it's true.

We're doing a kitchen, still, for my daughter-in-law, while they're living in the house. I built the cabinets and drawers of prefinished maple cabinet ply, and have been dragging my heels on building the cabinet doors and fancy drawer fronts, because life is busy. But I have to get this done.

The finish I'm using is Varathane Urethane Water based Spar, and it's fighting me. (It HAS to be the product's fault, you understand.) Brushing with a cheap brush lays down little patches of bubbles, many, but not all of which, will level out. The non-levelers get 400 grit, and another coat. Brushing with a Purdy XL is somewhat better, but still not a picnic.

I'm guessing that this is going to take at least three, if not four coats, at this rate.

I'd like to make wiping varnish from this stuff, like I do with oil-base and naptha, but the chemistry of thinning water-base scares me off. Or I could figure out how to shoot it, but only with the Critter sprayer I have. Don't want to spend bucks on any more spray gear, or a bigger compressor than the PC 6 gal pancake that came with the brad nailer kit.

Of course, the Varathane can and website say DO NOT THIN. I'm pretty sure why they're saying that, but it limits the hobby enthusiast somewhat.

I'm using the water-base because it's tough, and doesn't stink when applied, and it dries pretty quickly. And this looks a lot like the finish the maple is coated with from the distributor.

Any suggestions? I've got two coats on 8 doors, and there are another 12 doors to build, plus maybe 10-12 drawer fronts yet to do.

Re: A finishing question for the crowd...

#2

Paint pads *LINK*

Michael Dresdner

>Paint pads, which are flat slabs of red or yellow hard plastic affixed to a very thin sheet of what feels like hairy velvet, are designed specifically for applying waterbased paint, and work great with waterbased polyurethane. The very short white bristles are exactly what you need for waterbased clears -- bristles that are exceedingly small and soft, and too short to create air bubbles by flicking through the finish. Put on very thin coats using the paint pad to just barely wet the surface and you will find that you can zip through the job in no time. Last year my son and I painted a twenty foot long boat with two paint pads in well under five minutes. You will find them at Lowes, Home Depot, Target, Sherwin Williams, WalMart, all paint stores, and so on. In other words, any place they sell paint.


Paint pads

Re: A finishing question for the crowd...

#3

Yes!!!

Jason Roehl in Mulberry, IN

>I completely agree with Michael (he IS hard to disagree with...). But, I've stained/finished plenty of wet bars, bookcases and coat cubbies for customers using the pads of varying sizes. Basically any built-in casework where spraying was inappropriate (and I'm not shy about breaking out the sprayer). I will say that you can put on a slightly heavy coat, depending on the waterborne poly you are using. Too thin can just cost you more time because you'll need more coats. The pad shouldn't drag at all, but the viscosity of the poly should be your guide on that.

Jason (pro painter)

Re: A finishing question for the crowd...

#4

Re: Really???

Glenn Madsen near San Francisco

>Thanks, guys! I'll have to give that a try.

I had a pro painter friend on whom I relied for years, but he passed away about twelve years ago, and I've been pretty 'old school only' since then. This sounds like something to try, and won't cost an arm and a leg, either.

I love the answers I get here at Wood Central!

Re: A finishing question for the crowd...

#5

One more thing...

Jason Roehl in Mulberry, IN

>I use the pads with a flat, 9" roller tray. New is best, clean is acceptable. You will get some foaming in the tray no matter what you do, so don't worry about it too much, but don't work the poly too much in the tray, either. Just dip the tips of the bristles in the poly and pat them off a couple times on the ramp. I usually use the pads with the thin layer of foam behind the mohair bristles, getting it damp (not wet) before I start. You'll have to play around a bit with technique, but WB poly dries quick and sands easily...

Oh, I wouldn't worry about sanding between coats, either. To me, that's just a bunch of extra work with little benefit. If I haven't used a dewaxed shellac first, I'll knock down the raised grain after the first coat with a fine drywall sanding sponge/block. Otherwise I only do a light sanding right before the final coat, again with a drywall sanding sponge. It never made sense to me to put on a thin coat of something then sand it right back off.

Jason

Re: A finishing question for the crowd...

#6

Clean that pad befroe you use it!

Dave Bair, Eaton Rapids, MI

>Fresh from the bubble-wrap, these pads often are full of loose "hairs". These will fill that first coat with tons of flecks unless you clean the pad first.