Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Help for Delta Unisaw mobile base problem

Posts

Help for Delta Unisaw mobile base problem

#1

Help for Delta Unisaw mobile base problem

Steve in Jobstown, NJ

>Hi folks,

I have a new (less than two years old) Delta Unisaw with the 52" fence and table extension. The unit is on a mobile base that has fixed wheels on the saw end and one center caster that is activated by a cam lever which lifts the table end of the mobile base off of the foot pads. This enables the unit to roll and be moved.

I built a small 3/4" plywood, three drawer, cabinet under the extension table to hold saw related accessories. My probelm is that the weight of the cabinet is such that when the lifting cam is activated on the center caster, the table end does not lift high enough to raise the foot pads off the floor. The saw does not move. I have a small shop and this is a big problem.

Has anyone experienced a similar problem with their Delta Unisaw? Is there a solution other than removing the new cabinet? Is there an alternate method to lift the table end of the mobile base so the saw can move? I was thinking about some type of casters that I could mount on the mobile base that could lift the saw enough to roll, but I don't know where to find such a unit. Does anyone have any suggestions or has anyone solved a similar problem?

Thanks,

Steve

Re: Help for Delta Unisaw mobile base problem

#2

Re: Help for Delta Unisaw mobile base problem

Al Stokka - Cambridge, Iowa

>Steve,

You've probably looked into this but, just in case...

Can you screw the pads up into the legs enough to allow the base to roll?

Perhaps putting a shim under the lifting cam will give enough lift?

Al

Re: Help for Delta Unisaw mobile base problem

#3

Re: Help for Delta Unisaw mobile base problem

Steve in Jobstown, NJ

>Thanks Al,

Yes, to both. I have backed off all four foot pad screw posts so that the pads are as high as possible. I have also shimmed the cam to provide additional height to the center caster. Its apparent that the weight of the new cabinet is too much for the design of the mobile base lift capacity. The mobile base must be flexing under the weight of the cabinet causing the cam lifting mechanism to fail to raise high enough to clear the foot pads.

When I was searching for a Unisaw, I looked at a used one which had a homemade mobile base that had swivel casters that were lowered by a large thumb screw, or hand crank, assembly. These were welded to the frame and they easily lifted the saw when screwed down. Something like this might work if attached to my mobile base. I don't know where I could find such a unit (and I cannot weld either, so they would need to be mechanically fastened to the mobile frame.)

I wonder if Delta would have a solution? Are there any Delta Reps out there...?

Thanks again Al.

Re: Help for Delta Unisaw mobile base problem

#4

Re: Help for Delta Unisaw mobile base problem

Al Stokka - Cambridge, Iowa

>Steve,

I'm sure the mobile base could be reinforced to a point where flex would not interfere with the pads clearing the floor but, that doesn't sound like the best (read "easiest") solution for you.

I would look into adding casters to your storage cabinet in a way that the casters are between the mobile base's rails. Make sure that the vertical distance between the base's rail and the bottom of the cabinet is great enough that the rail won't touch the cabinet bottom when the mobile base is lifted by the cam. Doing this, the cabinet will always be sitting on the floor but, when you move the saw the cabinet will move with it.

Al

Re: Help for Delta Unisaw mobile base problem

#5

Which base?

Mark Goodall - ATL - tooljunkie

>Do you have the standard base or the elongated base?

I have the standard base which is square and does not extend to nor lift the extension tables legs. I only have the 30" Biesmeyer fence, and purposely did it thatr way. The extension legs are about 1" off the floor and are there only to prevent tipping in the event that I put something heavy on the far right of the table. I don't think this arrangement is possible with a 52" fence.

I have found that if I keep a box with all my saw blades (15 - verfy heavy) I have a hard time using the foot-peddle castor due to the extra weight. So I keep my blade box elsewhere and use the space under the extension table for a large box that stores all my sandpaper which weighs a whole lot less.

I don't think the regular or the extended mobile base could handle a heavy cabinet or box under the extension table.

Happy Woodworking!

Re: Help for Delta Unisaw mobile base problem

#6

What I did...

Jesse in New Mexico

>Not exactly an elegant solution, but I built a box that goes inside the mobile base with its height flush with the base rails. Then I put the storage cabinet on the box. When I move the saw (rarely) I slide the cabinet off the box and onto a mover's dolly. Then lift the box out and the base is free and clear. That way I don't worry about how heavy the cabinet and its contents are.

Re: Help for Delta Unisaw mobile base problem

#7

Re: Help for Delta Unisaw mobile base problem

Steve in Jobstown, NJ

>Thanks to all for some good suggestions. I like the idea of mounting casters on the cabinet between the mobile base rails. Unfortunately, I made the cabinet with only about 1/4 inch clearance between the mobile base rail and the bottom of the extension table.

I think I've spent more time trying to solve this problem then it took to build the cabinet :-)

Thanks again to all who took the time to respond!

Steve