Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Router users how would you jig this?

Posts

Router users how would you jig this?

#1

Router users how would you jig this?

Ernie Miller

>I need to make 10 or so fluted pilasters for a sun room I am bouiding I am thinking about making then out of 1" MDF they will go on each side of the windows and look like they are structural membors holding the roof up. I can buy 6" wide ones for about $40 each or I can make them for far less. I need to build a simple jig to rout the flutes I figure I will use a 1" box core bit but they all need to be straigh and start and stop at the same place I also need to make 5 flutes in each pilaster all spaced the same distance apart. I want the flutes to start and stop at the top and bottom of each window so they will be 62"~ I have a good plunge router but I am not a big router user can't stand the noise. Help ideas please.


img

Re: Router users how would you jig this?

#2

Re: Many options

Dave Mount

>Hi Ernie--

Lots of ways to skin this. . .er. . .challenge.

1) Put the router in a table and adjust the fence to get the flute spacing. If you don't have a router table, just drill a hole in a piece of thick plywood or PB, attach the router to the bottom, put it over sawhorses, and clamp a straight board to the topside for a fence. If the "table" sags, screw a stiffener to the back. If the flutes are to be "stopped" flutes, you can drop the workpiece onto the bit to do that. Mark the appropriate start and stop points on the fence.

2) Put a fence on your router. If you don't have one, then just make a sub-base for your router out of thin plywood and screw a piece of wood for a fence to it.

3) Use a guide bushing. Usually about $30 for a set if you don't already own them. Put the bushing in the throat plate and then clamp boards to the workpiece at the right locations to get the flutes where you want them.

Hope this helps -- e-mail me if it's not clear.

Best,

Dave

Re: Router users how would you jig this?

#3

Re: Router users how would you jig this?

Larry Clinton At Frankfort (Central)., Indiana

>Ernie, if I were doing this, I think I would make each column a 3 piece assembly. I would make the top and bottom separate. this way you don't have to deal with stopping the flutes. Don't believe it would show at all and be much quicker. You could use a router table or guide to mill the flutes straight through the center piece of the columns - make the piece double width, and route from each edge - then split the columns with TS. Then mill the tops & bottoms as shown (I would probably mill all four as 1 piece, then saw them apart). Glue up the top's & bottoms with biscuits if you desire or just align with caul's when clamping.

Re: Router users how would you jig this?

#4

Re: Router users how would you jig this?

John Lucas

>Ernie I have 2 jigs I use but the information is on my home computer. I'll try to remember to look it up when I get home tonight. One of them is a box that you install the turning into and the router runs on the top. The other is a table that fits on the lathe. I use my index wheel on the lathe and have a carriage that holds the router. Both are easy to build and to use.

Re: Router users how would you jig this?

#5

Re: Router users how would you jig this?

Ernie Miller

>These are flat not round Pilasters I am thinking about turning a round colume but may buy that. There is a time energy factor that has to play into this project.

Re: Router users how would you jig this?

#6

Step one

Bill Hammond, Oregon Coast

>>>> can't stand the noise

Get some in the ear noise plugs and then a pair of good ear muffs. Now that the noise is tolerable the rest will be easy... just follow the above advice

bill

Re: Router users how would you jig this?

#7

Re: Router users how would you jig this?

Kneale Brownson in Northern MI

>I'd do the three-piece assembly suggested earlier and make the fluted part with a molding head in a table saw. Still noisey, though, so you want ear protection.

Re: Router users how would you jig this?

#8

Re: Step one

Ernie Miller

>I have them things and use them regulary. It is more the high pitch ultra soninc vibrations or something. Heck I even use the ear mufs when the wife is talking. that sound can get to grinding on your teeth also. We live a quite peacefull life style around out house and some things are noisy no matter what procautions you take. The router is my least favorite tool so I use others when possable but in this instance it is the best one for the job. I want the round at the bottom of the flutes I coult cut them with a gouge and use a #16 hallow but that will take way to long might be fun but not an option. I'm leaning to using the router table set up I would only have to make three adjustments and 15 cuts total. The refinements at the top and the bottom are some pretty easy to make moldings that can be added after the flutes are made. They will be going into a sun room that will have the look of a Grecian Spa.

Re: Router users how would you jig this?

#9

Re: Step one

Bill Hammond, Oregon Coast

>>> Heck I even use the ear mufs when the wife is talking

Tried that too... and the resulting bandage helped to cut the noise..

remember that the MDF will be hard on the router bit and while you might forgo the dust mask when routing wood it's a good idea to use it when routing the MDF. If you put a long board on the table fence you can then clamp stop blocks to it and insure that the cuts all start and stop at the same place.

Bill

Re: Router users how would you jig this?

#10

Re: Step one

Ernie Miller

>I like that Idea. The Dc will definatly be hooked up and a mask is allways worn. Weather is almost perfect for it also mid 90's this weekens and 70% humidity. if I can get them both to climb a little higher I will be all set. The thought of it reminds me of Barning hay as a younger man.

Re: Router users how would you jig this?

#11

Re: Step one

Ernie Miller

>Do you think one bit will hold up for 300' of cuts with a touch upusing a diabond hone or should I pick up two just to be safe?

Re: Router users how would you jig this?

#12

Re: Step one

Bill Hammond, Oregon Coast

>I read somewhere that in hardwood expect 200 to 400 feet of routing before the bit starts to get too dull... now that was on a site that sells bits. Personally I would borrow a bit from next door.... Bits are cheep compared to your time and you really don't want to be sanding those flutes. I would get two and if it's not used you can take it back.

90 deg.... gee it's sunny today and if I keep the garage door closed it might get to 70 in there and I can work in short sleeves this afternoon.

new router arrives today, wonder how long it will take me to break it?

Bill

Re: Router users how would you jig this?

#13

Re: Step one

Ernie Miller

>Do you think I would be better off making these out of Pine or Popular? I have allways heard that MDF worked pretty good when routing anf for applications like this even though it is hard on bits any thoughts?

Re: Router users how would you jig this?

#14

Re: Step one

Bill Hammond, Oregon Coast

>to me it's the perfect application for MDF. It gets attached to the wall, painted and looked at. MDF won't split, bleed knots through the paint and it routs rather well even if it does eat the bits.. I think it will work just fine.

Be careful to support the board when working with it so it does not break.

good luck, bill

Re: Router users how would you jig this?

#15

Re: The other thing about MDF

Glenn Madsen near San Francisco

>is that this is all uniform. You don't REALLY care how thick it is, just that it's all the same from the same sheet. That won't be the case with pine or poplar, unless you make it that way. And that means more screaming universal motors and dead electrons. And another day or three fussing with it.

Git 'er done!

Re: Router users how would you jig this?

#16

Ellis Walentine

Just remember...

Ellis Walentine

>...that MDF is also very porous at its core, and not only will your flutes be s bit fuzzy to the touch, they will absorb a lot of paint. I would plan on a simple sanding, using a chunk of styrofoam shaped to the diameter of the coves as a backer, then seal everything well with sanding sealer or seal-coat. You might have to kiss off the nibs again with fine sandpaper before painting.

Ellis

Re: Router users how would you jig this?

#17

Ernie - Some Additional Thoughts

Howard In Toronto

>MDF is the perfect material for this project for the reasons stated above.

Ellis's sanding advice is correct.

The three-sided box is what I would do.

But -

With a twist....

No matter how well you prime and paint; and fill the seam between butt joints you will ALWAYS see the seam.

The way around that is to bevel these boards.

Yes, I realize they're really long but any infeed table helper and outfeed table helper will let you make perfectly good bevels assuming yor TS is accurate on 45 degrees.

I've done this on the router table but THAT is a scary proposition.

As for routing these flutes on a router table, here's what I would do -

- position the fence to rout the centre flute with two spacers between the board and fence

- rout the centre flute with the two spacers in place

- remove one spacer

- rout the next two flutes that are right beside the centre flute

- remove the last spacer and rout the outside flutes

BUT -

- if you want to "scoop" the ends of each flute you'll need to do it with a handheld router, edge guide and ramp-tytpe jig to lift the router up at the end

Not some thing I'd be willing to try...

HTH

Howard

Re: Router users how would you jig this?

#18

Build it in 3 pieces ...

Ian (in Sydney, Australia)

>Rout the flutes using a mortising base on your router (i.e. double fence registering off both sides) make two or more passes for each flute so the last pass is taking off about 1/64 or so (should help with the sanding)

cut all the centre channels without changing your setup,

do the same for each of the other flutes, don't change the setup till you've cut all of the particular flute

Make the flute sections overlength so you can cut the peaks off, back to a flat, where you'll attach the end caps.

I don't like the idea of balancing and controlling 60+ inches across a router table

Re: Router users how would you jig this?

#19

Re: Router users how would you jig this?

Charles Sharp

>Make a 3 sided box that will slide along with the MDF trapped inside. Drill holes in the top of the box that line up with the flute locations and fit your router bushing. Clamp a stop on the MDF to keep all the flutes the same length.


img

Re: Router users how would you jig this?

#20

Re: Router users how would you jig this?

Al Killian

>Make a template from mdf and use a guide bushing. Clamp the template to the peice of wood and insert the router into each hole and route away. This would be the easy way and wont take long once the template is made.