Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Drying lumber - removing the stickers?

Posts

Drying lumber - removing the stickers?

#1

Drying lumber - removing the stickers?

Stephen Kirk in Quakertown PA

>Well, over the weekend I had some time to dig down in my stack of oak which was stickered outside last August. The wood is amazingly light now. I grabbed a 4/4 board from around the middle of the stack to try out. I cut a section out of the middle of the board and then flattened and squared it up. It was kind of a nasty piece with knots and some wild grain. So far, the wood hasn't moved in the slightest, but I'll watch for a while. The wood cut extremely well and easily and smelled fresh(I can't really think of a better term to describe it). It didn't seem cool or damp during planing or cutting. No sticker shadow either. Also, most of my boards are pretty flat, minimal cupping but not much twist that I can see.

Is there anything else that can help me determine when it is safe to take the wood off the stickers and stack it tightly? I'd to clear off my drying area for the next batch (once I find it).

Re: Drying lumber - removing the stickers?

#2

what is your objective?

Bill Tindal, E.TN

>If your objective is to air dry the lumber for eventual kiln or equivalent drying then you may dead pack the lumber now. At this state it will not mold or rot dead packed. Once dead packed it will not loose additional moisture at a very great rate,

If the oak still has an acidic smell it is still pretty wet by furniture standards. Another measure is whether the planer shavings clump(too wet) or have static cling(nice and dry). Or stick a piece in the hot sun for a few hours and see if it cups or cracks. But best is to measure moisture content by the simple to do at home oven method which I have described many times. Unless you live in AZ it is doubtful the oak is dry enough for furniture. I

I prefer starting green lumber drying in the fall or winter. Much less danger of defects from too rapid drying or mold.

Re: Drying lumber - removing the stickers?

#3

Re: what is your objective?

Stephen Kirk in Quakertown PA

>My objective is to only use air drying. I had forgotten about the oven method, so I think I'll give that a try to see where I am in drying. The planer shavings didn't clump on me and seemed fairly dry. I'll also stick my test board out in the sun and see what happens to it. No real acidic smell left either, it just smelled like oak when I cut it.

Re: Drying lumber - removing the stickers?

#4

Re: sun test not recommended + other thoughts

Dave Mount

>Some of this is going to sound like I disagree with Bill. This is only partially true -- it would be more accurate to say that I think Bill's response is carrying some assumptions that may not necessarily apply to you.

First, I don't recommend the "sun test" Bill mentions. Virtually any air dried piece is likely to cup under this test, even if it's dried down to 10-12% (which, as Bill says, is as far as you're likely to get unless you live in pretty arid country). Weighing, oven drying, and reweighing, though it's a pain, is a better way to tell where you are. Alternatively, if you have a hardwood retailer around, they might be willing to stick the piece with a meter for you (buy something while you're there to pay back the favor; do not brag to them about your home-brew wood as they are not there to help you avoid having to buy wood from them).

Comments about whether air dried is dry enough for furniture depends on your assumptions. It is true that hardwood used for commercial furniture manufacture is brought down to lower MC than your wood likely is before being used. However, it would be incorrect to extend this to imply that the wood is too wet for you to use in building furniture. As long as you realize that in a conditioned environment the wood is likely to go lower after you build the piece, and build it to accommodate that kind of movement, you can build with that wood. IMHO, quality furniture should be built to easily withstand a range of say 4% to 15% moisture content.

I've built quite a bit if furniture over the last 15 years and almost all has been built with air-dried wood (my father has a small sawmill, but no kiln). I dry it on sticks to 12% (I have a meter), the store it dead-packed (without stickers) as Bill suggests in unheated but weatherproof outbuildings. I usually bring it into the shop for 3 weeks or so on stickers before I build; if it is winter, this will bring the MC down further, but not so in the summer. The important thing is that all the wood is at the same MC, whether that is 5% or 12%. After all, if I were to buy KD wood and keep it in my shop in the summer, it would soon be at 10-12% anyway.

In all the pieces I've built, only twice have I had problems with wood movement. Both can be traced to moisture issues that were secondarily related to me using air dried lumber, but the primary problem was my failure to build with that in mind. One example was when I didn't have any birch in the shop for drawer boxes for a case piece built of walnut that had been held in the shop in the winter. Without thinking it through, I got some birch from storage, milled it immediately and dovetailed the drawer together. Because the birch sides and walnut front were at different MC, the birch later shrank and the walnut didn't, which created a small lip at the bottom of the drawer front and also created some very small cracks at a couple of the dovetails. The failure was not catastrophic, but regardless, it would have been completely prevented had I acclimated the birch to the shop first.

The other failure related to some shop sawn veneer that I made from osage orange which, again, I got straight from the barn in the winter, sawed it into 1/10" thickness without acclimating and immediately veneered it onto a plywood substrate which had been in the (heated to 50 F) shop. The finished piece ended up developing a few very small checks in the veneer from shrinkage, which was caused by a combination of my impatience and using fairly thick veneer. Thinner veneer would probably have acclimated in an hour to the shop MC anyway, and would also have withstood any remaining shrinkage better.

There are some caveats here. The primary one relates to things like inset drawers. If you want "piston fit" drawers, you will face some challenge building with wood at 12% as piston fit at 12% will be less than that at typical inside-the-house MC. However, I don't find this is a problem, as piston fit drawers are an invitation to sticking drawers unless the environment of the finished piece is very tightly controlled. I live in northeast MN, and we don't have/need AC. As a result, with windows wide open on a summer night, the humidity in our house can get pretty high. On the flip side, when it's -20 F and the air to air exchanger running, the humidity in house in the winter is exceptionally low. Furniture exposed to these swings are not going to have piston fit drawers year around. I build with the idea that the drawer will be tight at about 12% MC will have some gap below that.

There have been past discussions here about whether a moisture meter is a necessity if you're drying your own wood. My position, and I think that of many others, is that no, it's not a necessity. However, it does make life easier, particularly if you don't always plan ahead adequately (like me) and want to know if you can "marry" wood with different acclimation history.

My somewhat more that $0.02,

Dave

Re: Drying lumber - removing the stickers?

#5

Re: sun test not recommended + other thoughts

Stephen Kirk in Quakertown PA

>I'm learning a lot more about building with wood movement in mind. I'm also looking at the amount of movement in different species so when I'm mixing wood I don't have a problem (say when using mortise tenon joints with all pieces having same grain direction but different woods).

I don't tend to acclimate wood for very long, so I think I've been lucky so far. But I should get into the habit of doing that. Luckily, my shop is just my garage which is often at the same MC as the outside world so I don't have much to acclimate to (unless it's winter when I have a heater on.) I think I'm also slow enough that my lumber has time to acclimate while I get around to doing things. 3 cheers for laziness!

I've also stared at joint layouts for a while thinking to myself that if it moves I'll have problems. Sometimes I over analyze the problem.

I may still try the sun method just out of curiousity. Learn by doing, as they say. Maybe pick up a moisture meter sometime just to make life easy too.

Re: Drying lumber - removing the stickers?

#6

Re: sun test not recommended + other thoughts

Larry Clinton At Frankfort (Central)., Indiana

>Dave, I have to agree with some of your thoughts. I use mostly air dried lumber, with some kiln dried mixed in. I have all my lumber stored in the upstairs room of my shop. I buy most of my lumber from estate type auctions, many from Amish families. There were several in the area that had sawmills. Most of the air dried lumber had been stored in unheated outdoor structures - barns storage buildings etc., course the lumberyard also stores the kiln dried lumber the same way. When I obtain a batch of "air dried" from these sources, I stack it with stickers, regardless of the MC. After 6 months or longer I check the MC - if under 12% (center cut sample) re-stack it solid. I have a Delmhorst meter and do check the MC occasionally. I have been surprised at the shift in MC during the seasons in my shop. I have seen 4/4 material as high as 10-11% and as low as 6. This is lumber that has been in my shop storage for over a year. The reason I am surprised is that my shop is heated -(never under 60 deg. F), and central air conditioned (never over 80 deg F. ) year around. I keep it at these temperatures to protect my equipment as much as the lumber. It doesn't cost a whole lot as I "super-insulated" the shop when I built it a few years ago. I haven't had much problem with wood movement - seems to me I have the same issues of wood movement after planing, when it is real dry as when it is higher in MC.

Re: Drying lumber - removing the stickers?

#7

clarification on "sun test"

Bill Tindal, E.TN

>Our lumber came in at industry spec of 7 %. Rarely we got a pack that was underdried. Underdrying showed up quickly if it was hot. The top layer cupped toward the air within a day . Lumber that came in at 7% was stable and stayed flat- even boards 20" wide.

I would agree that if you are satisfied with 12% MC lumber the "sun test" will not readily distinguish whether you are at 12% or something higher. But if the planer shavings feel dry you won't be much or at all above 12%.

Bear in mind the problems associated with 12% lumber. Yellow glue will take very much longer to achieve max. bond strength. Joint stress is much greater upon drying than expanding. I would put some effort in getting the lumber below 10%.