Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Opportunity to buy a second table saw. Should I?

Posts

Opportunity to buy a second table saw. Should I?

#1

Opportunity to buy a second table saw. Should I?

Don in Northern Arizona

>As we were walking the dogs this morning, I noticed a Rockwell/Delta contractor's table saw for sale a couple of streets over from us. They want $200 for it. It has a Baldor motor which is a plus. It has the old style fence which is not great, but I lived with one for quite a while on by current saw until I got my Excaliber fence. I have a later model Delta contractor's saw which has been a great saw for me.

A contractor friend of mine has two table saws set up back to back in his shop and he swears by this setup. He likes to set one up to rip and the other to groove, dado, rabbet, etc. with a dado set. I have space behind my table saw in my new shop where I was going to build an outfeed/storage unit. If I placed the saws back to back I could use them as outfeeds for each other.

I have been and will continue to be building a lot cabinets for the shop and house that require a lot of back and forth between the single blade and dado set. I also have a sliding table on my Delta, so I could also set up one with and good cross cut blade and the other with a pure rip blade for other situations. Anybody have this set up who can recommend it?

TIA,

Don

Re: Opportunity to buy a second table saw. Should I?

#2

YOU CAN NEVER HAVE ENOUGH TABLE SAWS.

Ken Oakley-Sunny St. Cloud, Fla.

>

Re: Opportunity to buy a second table saw. Should I?

#3

I disagree…

Rod Peterson -- Ormond Beach

>> Re: YOU CAN NEVER HAVE ENOUGH TABLE SAWS.

Sure you can. If you only have one cut to make, one saw is enough. It is true, however, that one can never have too many table saws.

Rod

Re: Opportunity to buy a second table saw. Should I?

#4

Re: Opportunity to buy a second table saw. Should

Ray Newman

>If I was in the situation you described, I would have gotten a friction burn from getting out my wallet�.

Re: Opportunity to buy a second table saw. Should I?

#5

Re: Opportunity to buy a second table saw. Should

Chuck Lenz

>If you buy the saw do me a favor and see if it has a Rockwell model 62-751 motor on it. I recently picked up a Rockwell 37-220, 6 inch jointer and it has the 62-751, 1 1/2 hp, 3450 rpm motor on it. I'm wondering if it is a contractors saw motor. 1 1/2 hp seems like a tad bit of overkill for a 6 inch jointer.

Re: Opportunity to buy a second table saw. Should I?

#6

Jim in Burlington Ont.

Jump on it

Jim in Burlington On

>If I had room I'd have 3. A giant panel saw and 2 other saw's one with a dado blade and one setup to just crosscut. I know a cabinet maker that has that setup and it speeds up work a incredible amount.

Re: Opportunity to buy a second table saw. Should I?

#7

This is like...

HC Sakman

>...asking bunch a wolves if they want another lamb! ;-)

Chico...

Re: Opportunity to buy a second table saw. Should I?

#8

Re: A word of caution

Loftguy

>Hi,

I also thought a second cabinet saw would be a good idea, so I got another one.

Then I thought a second band saw would be a good idea, so i got another one.

Then I thought a second planer would be a good idae, so I got another one.

Then I thought a second scroll saw would be a good idea, so I got one.

Then I thought...well, suffice to say its a dangerous addiction.

Bob

Re: Opportunity to buy a second table saw. Should I?

#9

That's ridiculous.....

Mark Goodall - ATL - tooljunkie

>I can't imagine anyone thinking or doing anything like that.

Jeepers, all you need is one circular saw, one router, one drill..... C'mon, why would you ever need more that that?????

;) ;)

Happy Woodworking!

Re: Opportunity to buy a second table saw. Should I?

#10

What would Noah do?

Mark Goodall - ATL - tooljunkie

>I'm pretty sure that Noah would have had two tablesaws. I mean, c'mon, he was specifically instructed to get two of everything, right!

One ark, but two of everything else.

I mean, c'mon, it's Biblical.

;)

Happy Woodworking!

Re: Opportunity to buy a second table saw. Should I?

#11

Anybody Remember Erik?

George@Colonel's Workshop-Havertown PA

>He was the guy who collected tools and never used them. Had enough drills to accommodate a full index of bits, one bit per drill----by 64ths! It seems to me he had a room full of table saws and another full of routers: A Fein router for the CMT bits, a Makita router for the Woodline bits, a Milwaukee router for all the Freud bits, a DeWalt router for those yellow bits they sold at Home Depot and Woodcraft Stores, The Hitachi Router for the old green Woodworkers' Choice bits, and Several P+C routers to spin Amana and Whiteside bits. He had a great sense of color coordination. :<)

George

Re: Opportunity to buy a second table saw. Should I?

#12

My big power tools are gray and elderly, like me

Don in Northern Arizona

>

Re: Opportunity to buy a second table saw. Should I?

#13

Bought it. More info. Rust removal help,

Don in Northern Arizona

>Well Chico warned me about your responses, and I am one too, Chico, so I bought it. He came down to $175, and the Baldor motor is a 2HP replacement, and that sold me. I have carved out some room in the shop and he will bring it over and we will unload it tonight. It has lived in the back of his pickup for a few months, so now I need advice on cleaning a lot (for Arizona) of rust off the top. I seldom have to deal with rust (gloat) so suggestions are appreciated.

Don

Re: Opportunity to buy a second table saw. Should I?

#14

Re: Bought it. More info. Rust removal help, *LINK*

Jim Dillon

>Don,

Congrats on your "new" old saw. I've had luck with minor rust on a table saw top using these abrasive blocks with some WD40, but I'm sure there are stronger chemicals available for rust removal. These blocks have some sort of abrasive imbedded in a rubbery compound. They worked well for me. Good luck.

Jim


Klingspor Abraser

Re: Opportunity to buy a second table saw. Should I?

#15

Re: Opportunity to buy a second table saw. Should

Don in Northern Arizona

>Chuck,

It has a 2HP Baldor replacement motor. I also have an old Rockwell Delta Milwaukee 6" jointer, the one with the 32" bed. Unfortunately it too has a replacement motor, but it is 6.2 amp or 5/8 HP. The current 6 in. JT 360 Delta has a 3/4HP motor. That sounds more reasonable to me for a jointer of that size.

HTH,

Don

Re: Opportunity to buy a second table saw. Should I?

#16

Thanks, Jim!

Don in Northern Arizona

>

Re: Opportunity to buy a second table saw. Should I?

#17

One left tilt, one right tilt?

John in New Mexico

>

Re: Opportunity to buy a second table saw. Should I?

#18

Re: Was he the one who signed off with "Hey sailor

Al Crandall (N.E. of Indy)

>"Hey sailor, got a Moak?"

Re: Opportunity to buy a second table saw. Should I?

#19

Re: Naval jelly.

Al Crandall (N.E. of Indy)

>