Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Rubbing compound for wood

Posts

Rubbing compound for wood

#1

Rubbing compound for wood

Jim

>Recently completed build-in bookshelves for a new office. I had to make the shelves in sections to get them through the doors (new office complex, owner didn't want the mess of making them on site).

For a finish I used a wood conditioner, and poly S.G. sprayed with HVLP spray gun (first time). The finish is not as smooth as I would like,even after two coats and sanding in between, am sure that I will get better with the gun over time.

Someone in a posting mentioned using a rubbing compound and wax, anyone had any experience with either or both and maybe a possible alternative solution. Big client!!

Re: Rubbing compound for wood

#2

Re: Rubbing compound for wood

Jim Shaver - Oakville, Ontario

>Hi Jim,

I have often rubbed out a clear coat finish with 0000 steel wool and wax, it's worked well for me in cutting the surface and leaving a level smooth finish.

Another option, and I have done it once, is to use pumice stone (2F and 4F) and rottenstone. I used this process once, wet sanding with water and on a poly clear coat fisnish (several coats built up). It worked really well, it was a chore though. I just checked my shop, I have the product from Behlen.

Not sure i fthis helped you or not.

take care,

Jim

Re: Rubbing compound for wood

#3

Re: Rubbing compound for wood

john lucas

>I've done both of what Jim suggested as well as using white automotive compound followed by a good paste wax. Furniture wax that is, don't use automotive wax, it dries white and can get stuck in all sorts of places. You don't want to know how I know this.

I used murpy's soap with my pumice and rhotenstone. For a nice satiny sheen I like the 4/0 steel wool followed by funiture wax.

Re: Rubbing compound for wood

#4

Re: Rubbing compound for wood

David Harker

>I'm thinking of getting into woodturning, have read about it, and know that many woodturners use rubbing compound as part of their sanding/finishing process. Do a search for that on the wood turning portion of this website.

Re: Rubbing compound for wood

#5

Ellis Walentine

Flattening a bumpy finish...

Ellis Walentine

>...is a job for a sanding block, because a flat backer will cause the sandpaper to only hit the high spots. I wrap 220-grit stearated sandpaper around a piece of styrofoam insulation and sand the high spots and nibs flat. Then I recoat with whatever topcoat I'm using. Once you get past the exposed wood fibers, it will start laying down smooth. Just make sure you are using gloss product, or else you will obscure the grain. You can rub out the final coat with 0000 steel wool to cut the gloss and get a nice satin/matte look. Instead of wax, I recommend a very thin wiped-on-and-rubbed-out coat of the same varnish to saturate the scratches left by the steel wool.

Ellis Walentine, Host

Re: Rubbing compound for wood

#6

Re: Caveate

Mark Mandell - Gone Round In Jersey

>Don't use stearated paper if you're using a waterborne finish. Fisheyes and pealing are sure to follow.

Re: Rubbing compound for wood

#7

Be Careful...

David Yoho

>Nobody mentioned this and maybe you know it, but... if you're going to sand with paper or some type of rubbing compound and don't plan to apply more clear topcoat, you might want to let the finish cure first. It might be too soft and cause a bigger problem before then.

David

Re: Rubbing compound for wood

#8

Re: Rubbing compound for wood

john lucas

>Only a few turners use rubbing compound, usually the ones that do the really thick super glossy finishes. I know Mark Kauder uses automotive rubbing and swirl remover compounds. Many turners are now using the Beal buffing system which is really more like doing the finish on a car with a power buffer than hand rubbed buffing finishis like those done on furniture. Factory made guitars are power buffed this way also. It's a beautiful finish.

Re: Rubbing compound for wood

#9

Re: Be Careful...

john lucas

>You are correct David. I had to wait 4 weeks for a table I did with a polyeurethane finish to dry enough to not pill up when I sanded to level the surface before final buffing. I used Pumice and Rhotenstone on that one.

Re: Rubbing compound for wood

#10

Re: Poly Rubout

Mark Mandell - Gone Round In Jersey

>Seems like a very long time to cure, John. Usually a oil-based poly is sandable in 7 days. When leveling poly, I like to use 600-800w/d SiC paper lubricated with mineral spirits, then 4/0 wool, followed by Meguire's (auto) Nos. 2, 3, and 9. An oil finish will continue to shrink down onto the surface for a month or two, depending on conditions, but the gloss should remain. I've used oil poly on walnut in order to allow the tiny grain pits to reappear slightly in the surface; negates that "plastic" look that poly gets when put on too thick.

mm

Re: Rubbing compound for wood

#11

Dale Lenz

Re: What I do

Dale Lenz

>First, never have spray/used poly. I'll spray 4-6 coats of lacquer and let dry to the touch, then after a few hours, sand down with 400 or finer grit paper. If I'm after a high gloss, will let the lacquer cure for 3 days, satin sheen 2 days, or so after my last application of coats. Satin sheen, 4-6 coats, high sheen build, 12+. Sand after the above time lag, then use Migurars(sp?), like someone mentioned above with a wool bonnet and a power buffer.

I'd think two coats on poly is kinda lite build and I'd guess the poly an oil base, is not cured in your time frame.

Re: Rubbing compound for wood

#12

Can you explain what you mean by....

Howard G

>apply light varnish and then rub-out. I assume you mean rag on similar to french polishing, but what do you mean by then rubbing out if the goal is to fill in the steel wool scratches? Lool forward to your response.

Re: Rubbing compound for wood

#13

Ellis Walentine

Easier to show than explain

Ellis Walentine

>Properly rubbed, 0000 steel wool will produce almost imperceptible scratches. I use just a very small amount of varnish and apply it with a small piece of rag like a polish -- just enough to saturate the hazy look produced by the steel wool, but not enough to actually build a film of any appreciable thickness on the surface or fill these tiny scratches level. You need the scratches to diffuse the light and give the glossy film the appearance of a low luster. The surface should feel almost dry to the touch when you're done. If it still looks a little thirsty, repeat as necessary. This assures a dust-free finish without the glossiness of a cured film. Polishing the dried finish later with a soft cloth will yield a slightly more lustrous sheen if desired.

Hope this sheds more light on the subject. :-)

Ellis Walentine, Host