Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Planning a shop.

Posts

Planning a shop.

#1

Planning a shop.

Gary Evans Tallassee, TN

>Hi all,

I thought that when I got to the point of actually setting up my new shop, the layout would just sort of become apparent. As it is, I'm looking at a 38'x16' space to fill with a lathe, bandsaw, tablesaw, compound miter saw, 6" jointer, 12" planer, dust collector, 18" shaper, lumber storage, plywood storage, handtool storage, benches, etc., in an arrangement that will promote efficiency in our work.

The lathe is already designated to go against one of the short walls. I'm going to have a polycarbonate window there where I can see who comes in the store and customers can watch what's going on with the lathe without danger of flying objects.

I know that there are several good books out there on woodshop design, which I may have the opportunity to go get at some point, but I need a rapid response, 'cause I'm a long way from town and the shop is one of the things I need to get out of the way so that I can proceed with the rest of this project.

In other words, I need a working shop in the shortest possible timeframe. Any sources on the web for ready answers would be appreciated. It just occurred to me to take a look at our articles and shop shots. I'll go do that now.

Thanks,

Gary

Re: Planning a shop.

#2

This place is incredible!

Gary Evans Tallassee, TN

>I just did a quick look through the WC articles. "Workflow Planning" by Kim Carleton Graves gives a very nice outline for looking at shop layout. Thanks, Kim.

Any other resources would certainly be appreciated. I figure I've got a couple more days of clean-up, etc. work before I'll be ready to start spotting tools.

Gary

Re: Planning a shop.

#3

JL

Re: Planning a shop.

JL

>I like doing layout with the "Dreamshop planner" at Grizzly.com (scroll down to the bottom, it is the last icon on the left hand side). I found it very helpful to "spot" tools and cabinets.

Re: Planning a shop.

#4

Re: Planning a shop.

Bill Turpin in WNC mountains

>Put in twice as many electrical outlets as you think you need. Hi and low on walls, ceilings above work benches. After you have done this add ten more! I HATE to play switch the cords when I'm using a router, drill, sander, skil saw and jigsaw on the same project.

Bill

Re: Planning a shop.

#5

Re: Planning a shop.

Keith Newton

>I don't know about using polycarbonate behind the lathe. It is very easy to scratch. I think it will get too clouded to see through very soon. I would think about tempered glass.

Re: Planning a shop.

#6

My system

jeff

>I have a simple system that works.

I run alot of outlets (and I mean alot), both 120v and 220v along the walls (at counter height) and in the ceiling.

Then I throw all the equipment in the shop (on mobile bases if I can) and start working.

Usually, I'll put the table saw in the middle.

Then, as I work on projects, I gravitate toward the most used equipement and move them into a better working spot for me.

After a few years, everything has a home in the best place.

I'm in my current shop now ten years (give or take) and just finished a few more moves yesterday.

Keep at it, you'll get it.

Jeff

Re: Planning a shop.

#7

Re: Agree with Jeff

Larry Clinton At Frankfort (Central)., Indiana

>I have mobile bases on just about everything in my shop. This includes my Unisaw, MM16 band saw, 8" jointer, 12 & 20" planers, Tool boxes, Router table, assembly table & Scroll Saw. I have several foot of flex 6" and 4" dust collector lines. I piped my Cyclone overhead and installed several drops with gates. I installed 120V outlets on every other stud throughout the shop at about 54" high. Then added several just because. I installed 12 or so 220 outlets. I made up several extensions for the 220 and 120 volt equipment. I find that the project I am working on determines where I need my equipment. IE: Working on my sons house trim, (making from rough sawn oak) requires several foot of clearance in an out on the saw, jointer and planers. This is not where I want the equipment when I am working on the (current project) blanket chest. Although I have a dedicated shop, I do occasionally need to repair a vehicle in it. Having the equipment on rollers makes it easy to clear out an area. Maybe someday I will find the perfect location for everything - but I doubt it.

Re: Planning a shop.

#8

Re: Planning a shop.

arw01

>If you want a 3-d perspective, spend some time with sketchup to make up your shop space. There are tools available for download from the Google Warehouse which are drawings of all the various pieces you will need to place, including a lumber rack.




There seem to be two schools of layout.

A circular flow

and

a workcenter flow.

I like the cluster approach more than the along the walls approach. So I put my table saw, planer, chop saw, and jointer into a triangular or rectangle pattern. I can walk around them quickly to each other. Use each other for outfeed support, and have cabinets in my planer/chop saw support.

This also allows easy access to dust collection with a minimum of the octopus look.

Alan