Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Fixing a 333 PC ROS

Posts

Fixing a 333 PC ROS

#1

Fixing a 333 PC ROS

Barry Irby

>My PC ROS died a week or so ago and I did not want to drive it to the repair center and Pay their minimum, etc.

Posted here about it and got some advice.

Took the platen off and finally figured out it was the bearing in the center of the platen support. Took that off and tapped the bearing out with patience and a screw driver in lieu of a punch. Went to NAPA and bought a bearing. $15 bucks but still cheaper than ordering one on line and paying shipping. Installed the bearing. Used the rim of the old bearing to drive it in and seat it. Broke the rim on the Platen support, so in a fit of pique I epoxied the bearing into the support. Next morning I tried to complete the assembly only to discover that the bearing was miss-manufactured and the hole in the center was 3/100" under sized. Believe it or not, I managed to remove the bearing. So much for epoxy. Ordered a replacement bearing and carrier from Service.net. They came today and I reassembled the sander without further incident.

I like that sander, but it might have been better to buy a new one.

Re: Fixing a 333 PC ROS

#2

Patience of Job

George@Colonel's Workshop-Havertown PA

>Good Afternoon Barry,

All that time spent in mounting frustration qualifies you to a new sander. I am glad you finally got it going. I wouldn't have had the long term patience you exhibited. I'm using my P+C today. I like the sander also, but not nearly as well as you do. :<

George

Re: Fixing a 333 PC ROS

#3

Re: Patience of Job

Barry Irby

>George, I actually left out a step or two. I decided I could buy a new one for about $44, so the old one might not be worth fixing. I went to Lowes (a mile away) and they wanted $54, so I went to HD where I had seen it for $44, but they had raised the price to $54 also, so I bought it. Got it home and realized they have changed them. They are not 333 anymore, they are 343. They have a sort of oval wide mouthed fitting for the dust catcher and the pad has eight holes instead of five. I took the pad off and looked at the guts. Obviously not as well made and the 333 and marked "made in China." So, I have a DC connection that works on the round 333 port, but no way to hook up the 343. I have a bunch of five hole sandpaper on hand that won't work well on the 343 and I did not like the looks of the cheap Chinese made parts. I went back and looked again. The one on dispaly was a 333, but all the ones on the shelf were 343's. I think they sold all but the display at $44 and then went to $54. I took the dispaly, but they would not give me a discount. Said their system did not show it anymore. So now I have two. The one I repaired is a VS model that sold for about $80

Re: Fixing a 333 PC ROS

#4

Too Bad, Barry

George@Colonel's Workshop-Havertown PA

>I thought the 333 was a good sander, and now its replacement is Chinese made, and not as good. I would have suggested changing the pads to retain the five hole configuration is that were possible. My take is that the five hole configuration is not as efficient as the 8 hole, which I have on my Ridgid, my malfunctioning DeWalt, and had on the defunct Bosh 1295.

And, you tell me HD wouldn't do you a deal on a shelf display model of a discontinued item? We must be shopping at the same box store!

George

Re: Fixing a 333 PC ROS

#5

Re: Too Bad, Barry

Barry Irby

>George, I think if I had gotten to a Section or Store manager they would have given me a deal, but I was in there on Sunday and they had the Second String in.

I have replaced the pads, but they are about fifteen to eighteen bucks. I like the ones that have the slots in them so you can use either five or eight hole, but I was already spending about a third the cost of the sander on a new bearing, so it did not make sense to buy a new pad too. Also, the oval or sort or cartouche shaped dust port may actually be better (bigger), but I don't have an adapter for it to my DC. I know I was pleased with my 333 and it lasted about seven or eight years. I was skeptical or the 343.