Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Labeling shop drawers....

Posts

Labeling shop drawers....

#1

JL

Labeling shop drawers....

JL

>I'm putting on drawer fronts on my shop drawers. As there will eventually be a total of 17 drawers on that wall, the subject of labeling drawers came up with the LOML.

I do have the small cheap plastic cabinet filled with screws. Those drawers are all labeled - but hey, there are lots of little drawers with a large variety of screws.

I can see labels on the inside of my saw blade drawer, telling me which blade is which.

So - labeling - yes, no or haven't really thought about it? If it matters, the drill stuff will be in the drawer unit near the drill press. The hand tools will be on the end near the eventual location of the work bench. These are widely separated.

Re: Labeling shop drawers....

#2

Re: Labeling shop drawers....

Pat Evans

>I know where all my stuff is without labels. The only reason I have any drawers labeled is so my Dad can find things.

Re: Labeling shop drawers....

#3

Re: Labeling shop drawers....

Ron Hildreth, Alta, Iowa

>JL,

Several months ago I finally got around to building drawers and cabinets in my shop, so that now when everything is put away, none of my hand tools, screws, nails, any hardware, etc. is out of sight. At first I was going to label everything, but didn't get around to it right away and discovered that I really didn't need to. I nearly always know where everything is, with the exception of those times that I suffer a "Senior Moment"!

Labeling things has it's pros and cons. Occasionally I have a few locals that like to help in the shop if I'm doing something for them. Most are OK, but one or two I would prefer they didn't know where things are. I've been looking at a building on Main St. here in town and moving my shop out of my basement. I can't imagine what it will be like then. I'll have to lay some ground rules and make sure the insurance is paid up!!

Ron in Iowa

Re: Labeling shop drawers....

#4

Mine say Fruit of The Loom-----

Ken Oakley-Sunny St. Cloud, Fla.

>or sometimes Hanes

Re: Labeling shop drawers....

#5

Re: Labeling shop drawers....

Clint Searl, at the base of Haycock Mtn

>I built a 32 drawer (4 high x 8 wide) 16' storage unit along one wall of my shop. Aside from some slight variations in the drawer dimensions, they all look the same and aren't labeled. I often go to the wrong drawer for what I'm looking for, and it takes a couple tries, but at least I don't have to squat and squint to find the right one. The searches are good mental exercises.

Clint

Re: Labeling shop drawers....

#6

Re: Labeling shop drawers....

Curly Smith

>I'd only label the infrequently used ones, if I labeled any at all.

If I labeled the commonly used drawers I'd spend time reading the labels looking for what I wanted rather than just opening the correct drawer. I find that if I write stuff down my brain decides that it's not important, if I don't write stuff down I have much quicker recall since the old brain isn't saying "uh, you've got your notes don't you?".

Re: Labeling shop drawers....

#7

Dale Lenz

Re: Labeling shop drawers....

Dale Lenz

>I labeled mine with masking tape and a Sharpie. It been almost 10 years now since I did this, the masking tape is getting transparent now, so they will be falling off in the next few years. I think I've got them memorized by now, : ' >.

Re: Labeling shop drawers....

#8

Re: Labeling shop drawers....

DB

>If she wants you to label the drawers in your shop, then label the ones in her kitchen.

Re: Labeling shop drawers....

#9

JL

Re: Can't do that....

JL

>then I'd have to end up putting things away in the kitchen :). As is I just wash the dishes and hand off to her for drying :).

Re: Labeling shop drawers....

#10

Bart Goldberg

Perhaps Victoria's Secret?

Bart Goldberg

>

Re: Labeling shop drawers....

#11

The Investment Banker's Focus.......

George@Colonel's Workshop-Havertown PA

>Is The Bottom Line.

George

Re: Labeling shop drawers....

#12

Re: Labeling shop drawers....

George@Colonel's Workshop-Havertown PA

>Good Evening JL,

I've a bunch of drawers in my shop and none is labeled. I pretty much know where everything is, so labels are unnecessary. I do mark each tool box with the contents, and that makes it convenient since the boxes can migrate from one shop room to another.

George

Re: Labeling shop drawers....

#13

Good thing!!!

Derek

>Dale,

You said: "I think I've got them memorized by now"

I think that is a good thing, since the eyes start to go after a while! Of course, the memory goes next.

By the way, there are three ways that you know you are getting old:

1) Your memory starts to go

2) ...I forget the other two