Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Where hardwood comes from 3-log yard

Posts

Where hardwood comes from 3-log yard

#1

Where hardwood comes from 3-log yard

Bill Tindall, E.TN

>Part 3 The Log Yard

Finally in Part 3 we get to see some wood!

After harvesting, the logs are hauled to the log yard. They may be hauled directly to the mill if the mill is close to the logging site or there may be a remote log yard that serves as a collection point for area logging. From this remote yard the logs are loaded on larger trucks, usually tractor-trailers, that can haul 4000 bdft of logs to the mill. Recall that the trucks typically used by the loggers to haul logs from the logging site only can haul 2000-3000 bdft of logs, and it would not be economical to haul logs a long distance on these trucks . A typical log yard is show in the picture. The crane with the log grabber on its end is used to load and unload trucks on the yard.


img

Re: Where hardwood comes from 3-log yard

#2

contunued

Bill Tindal, E.TN

>The logs are removed from the in-bound log trucks and spread out so that they can be inspected. They are graded and measured and they may be tagged with some identification that records their species, source and size. The board feet that the log will yield is calculated from the length and diameter of the log and the kerf of the saw that will be used to saw the log. Log rulers have this calculation built into the scale on the ruler so the person measuring only needs to hold the ruler up to the log to determine its yield in board feet. The owner of the logs will be paid by the size and grade of the log. As an example the current price paid for a clear, large red oak log is about $0.50 per bdft, while a small red oak log, or one with several knots, would sell for only $0.20 per bdft. Logs are sorted, moved around the yard and piled with the machine show in this picture. The big log in the picture is a red oak. Some inventory tags can be seen on the log ends.


img

Re: Where hardwood comes from 3-log yard

#3

contunued some more

Bill Tindal, E.TN

>This picture shows a portion of a log pile. This pile is unusual in that it has not yet been sorted by species. Log piles on the yard are normally sorted by species because one species at a time is normally sawed. The logs with the red ends are cherry and most of the other logs are poplar. I show this picture to settle an issue that has been in dispute on Wood Central and to illustrate a trend in hardwood lumber quality. With the development of highly mechanized mills, as well as other market factors, it is now practical to saw logs as small as 10�, the size of the smaller logs shown in this picture. This fact has an impact not only on the quality of lumber being sold today, but on future supply. If trees as small as 10� are harvested today, it is going to be longer for the forest to grow back large trees. Twenty years ago it was common to get oak and poplar boards 12� and wider in typical wholesale packs of hardwood lumber. Not any more. Wide lumber is going to become even more uncommon in the future. If you have an opportunity to buy exceptional quality hardwood make the investment if you can afford to. I can only see the trend in quality going down and price going up. Many of the best logs that would have been sawed in times past are now sold as veneer logs. Veneer logs are worth at least 50% more than the best saw logs and the sky is the limit for the very best veneer logs. These are the logs that yielded the most desirable lumber (wide and clear and/or figured) when they were sawed.


img

Re: Where hardwood comes from 3-log yard

#4

........to settle an issue ?.........

Scott in Eastern Iowa

>.....Thanks for the post and pics Bill.

Now....What was the issue here on WC ?

Re: Where hardwood comes from 3-log yard

#5

since you raise the issue....

Bill Tindal, E.TN

>In the past some have argued with me on this Forum that loggers don't harvest trees less than XX" , with XX being quoted as something a lot bigger than 10". Indeed this was a fact 20 years ago when it cost too much to saw dinky logs. But now days I see a lot of small logs on log yards, especially walnut, maple and cherry.

Re: Where hardwood comes from 3-log yard

#6

Dale Lenz

Re: since you raise the issue....

Dale Lenz

>Bill,

You are doing a great service to the WC community for your story from trees to lumber. Many mills will purchase logs with an 8" top around here for sawlogs. I suspect most of the lumber from these logs are going to pallet wood. My personal rule when I ask a sawmiller/logger for lumber: nothing smaller than a 14" diameter on the small end, as I get too much cupping from lumber sawn from a 10" log.

Thanks again for you post

Re: Where hardwood comes from 3-log yard

#7

thanks for the encouragement

Bill Tindal, E.TN

>Part 4 the sawmill will be next week. I may do several weeks on the saw mill.

Re: Where hardwood comes from 3-log yard

#8

JL

Re: Thanks for the posts - unified article...

JL

>eventually?

Re: Where hardwood comes from 3-log yard

#9

Re: since you raise the issue....

Jim Swank

>In Arkansas, there are 3 types of sawmill - pallet, tie, and lumber. Pallet mills will take down to 8", with a minimum length of 42", though most sawyers cut 48. They don't care much about species, but won't accept spalted logs. They often pay by the pound rather than the bf. Tie mills want an 8' log. I forget if the small end must be 8" or 10". They also don't like spalt.

There's chipper mills too. I don't know their requirements or practices, but a lot of their output is exported.

A small tree's best chance of growing to maturity is if it grows a good long distance from one of these mills, since time and fuel costs offer some degree of protection.

Re: Where hardwood comes from 3-log yard

#10

Re: since you raise the issue....

Ted Wong

>It's not only true in hardwood mills but also the big softwood mills on the Pacific coast have been cutting smaller and smaller logs for years. Basically because that is all that is left, 2nd and third growth and now wood from the tree farms planted 20 or so years ago.

If you drive down some of the rural routes in Northern CA you'll see logging trucks carrying some pretty dinky stuff, 8" or so.

Re: Where hardwood comes from 3-log yard

#11

what did you have in mind?

Bill Tindal, E.TN

>

Re: Where hardwood comes from 3-log yard

#12

JL

Re: All of the posts and pictures...

JL

>together in the WC articles section. The posts have opened my eyes to certain procedures. Thanks for posting them.

Re: Where hardwood comes from 3-log yard

#13

Re: Where hardwood comes from 3-log yard

Don O.

>Interesting series you have going here Bill. Keep it coming and thanks.

Re: Where hardwood comes from 3-log yard

#14

Re: Where hardwood comes from 3-log yard

Stephen Kirk in Quakertown PA

>Bill, thanks for the info and the pics. Definitely, keep it up.

I noticed one other thing that is often a hot topic when cutting logs - none of the ends in your pictures are sealed.

Judging by the way our lumber prices are climbing, it seems likely that we are quickly cutting our way through a lot of trees and that they are getting harder and harder to find. I consider trying to saw up my own lumber more and more (and I'll probably have room for more, soon!). It's not hard to find 24" and 36" logs coming from a home that took down a tree. Heck, it's almost worth the cost of a few blades (if metal is found) to cut it up anymore.

Re: Where hardwood comes from 3-log yard

#15

end sealing

Bill Tindal, E.TN

>I have seen millions of feet of logs and lumber in this area and never seen sealer on any of it. Some body uses it, but I don't know where or under what conditions. I never used it. End checking just wasn't a serous issue to worry about. There are so many other places to put effort when drying lumber that pay bigger dividends.

Re: Where hardwood comes from 3-log yard

#16

It's in process…

Rod Peterson -- Ormond Beach

>I've been grabbing the text and pictures as Bill posts them and formatting them to WoodCentral style so the compilation will be ready when Bill finishes the series. We even have a number assigned to it already.

That's all subject to Bill's approval, of course.

Rod