Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

OT--finding a broken wire

Posts

OT--finding a broken wire

#1

OT--finding a broken wire

Gary Evans Tallassee, TN

>Hi all,

During the current discussion around the household regarding providing water to the garden which I posted about the other day, my wife reminded me that I used to have power to an old barn that is somewhat closer to the garden than the house is.

I have a set of #4 wires running down there, but I lost one leg several years ago, so just disconnected the wires and left them in the ground. If I had some way to find the break without digging up the whole 400' run, I could have real power available to operate a pump for the garden.

Any suggestions on a do-it-yourself way to find out where a wire is broken? I can put power back on the circuit pretty easily if necessary.

I appreciate it,

Gary

Re: OT--finding a broken wire

#2

Re: OT--finding a broken wire *LINK*

Scott in Montana

>Good Morning Gary.

What you need is a time domain reflectometer... or as it is more commonly known, a cable fault finder (Harris TS100). Once calibrated (simple) to the gauge of your wire, you disconnect both ends of the cable and attach it to one end of your wire. It will tell you at how many feet the short or break occurs. It has been my experience that you should be able to measure the distance to the break within a foot or two on a run of that length.

You might be able to borrow one of these test instruments from an electrician, telephone guy, or a business that wires homes for audio/video. I'm not sure if a rental place would have one or not. If you wanted to bite the bullet and buy one, I remember paying about $300 for my current one. I have attached a link to the Harris model.

Good luck!

Scott


Harris TS100

Re: OT--finding a broken wire

#3

Re: OT--finding a broken wire

Larry Clinton At Frankfort (Central)., Indiana

>You might contact your utility company and ask what they would charge to locate it for you. They have the instruments (expensive) that will pinpoint the break. One of the methods they use is a Time domain reflection system that sends out a signal that is bounced back at the break. This lets them know how far it is from the point they connect to the break. May not be too expensive - could be free. I would sure ask. Otherwise you may call some electrical contractors in your area and see if they have the equipment. In any case it should be much cheaper than digging up spots and checking. There is a "splice kit" which can be used to repair wire breaks. It is made for High Voltage (as I remember around 13K volts max) underground lines. I have repaired underground romax lines with the kit. It consists of a plastic container that clamps around the spliced wire, with rubber seals on the ends. After you have spliced the wire, and installed the container, you fill it with the supplied epoxy. Think I paid about $20 for a kit about 15 years ago.

Re: OT--finding a broken wire

#4

Re: OT--finding a broken wire

Curly Smith

>Your local utility company is probably the best bet. However, you can try connecting the suspected bad wire to a spark plug wire. Then with the engine running, or somebody yanking on the lawnmower starter rope, tune an AM radio to find the "tick" when the spark plug should fire. Once the radio is tuned, walk the line. You'll locate the break when you stop hearing the spark plug tick. Naturally, you'd want to disconnect the wire from any power source before trying this method.

You might also consider one of the Christmas light testers or something like this: Live-Wire� Tester but I don't know if they will work with buried cable.

Re: OT--finding a broken wire

#5

Re: However you find it......

Kneale Brownson in Northern MI

>There's a reason the wire quit working. You'll probablly find two wires with burned off ends because one arced to the other. I had the same thing happen to wires I buried to my barn after they'd been in place for years. Apparently the shielding broke down even though it was supposed to be underground cable. I patched with those rather expensive underground splice kits and that lasted another few years before failing. Apparently there's too much water in my ground or something.

My ultimate solution (in place now longer than the patches and longer than the original bury--a BTDT that's one of the very few benefits of growing old) was to dig a new trench to the barn and bury the wires in conduit.

Re: OT--finding a broken wire

#6

Re: However you find it......

Bill Howatt

>I was talking to some local linemen once and they said they often find a rock beside cable breaks. Our soil is mostly like beach sand beneath the surface so rocks are relatively uncommon.

Considering the work involved installing a cable, putting in conduit at the installation time is probably pretty cheap protection.

Bill

Re: OT--finding a broken wire

#7

Re: OT--finding a broken wire

Barry Irby

>I have a (Now abandoned) Invisible Fence. One of those underground wires that sends a signal to a collar your dog wears. If you get a break in it you can tune a portable FM radio to a certain frequency (540?) and hold it just above the the ground where the wire is buried. You follow the wire and hear static until you get to the break and it goes silent. You might be able to borrow an invisible fence unit from somebody long enough to try this. OTOH, It might not work, because the Dog wires are only buried about two inches deep and hopefuly, yours are deeper than that.

My power with out and the local power company came and found the problem. The contractor installing the lines for the neighborhood years ago apparently left a chain in the ditch and the current shorted to the chain when the insulation began to degrade. I used the chain for years after they gave it to me.

Re: OT--finding a broken wire

#8

Re: OT--finding a broken wire

Bob Fawcett

>Utility companies locate wires with a similar tool. If generates a signal on the wire and a handheld reciever unit is swept across the ground to locate the wire. There are services that will do this for a fee.

How deep is the wire buried?

Re: OT--finding a broken wire

#9

Re: OT--finding a broken wire

Gary Evans Tallassee, TN

>Hi Bob,

I was just talking to a friend of mine tonight who works for the phone company. She's going to check and see if any of her techs use that kind of tool.

If I can't get them to come locate the break, I still have a friend at the electric co-op. They may also have one of the tools.

The wire is buried about 2' deep.

Gary