Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

OT-Propane Plumbing

Posts

OT-Propane Plumbing

#1

OT-Propane Plumbing

Dave Bair, Eaton Rapids, MI

>I'm having trouble getting someone to plumb a propane line for a new cooktop. There is an existing plugged T on the main propane line that's pointed in the right direction. The instructions look to be straight forward and it's clearly not rocket science to cobble together some black pipe without leaks. What's the downside to doing it myself, assuming I follow the directions (and remember to shut off the gas at the tank first)? When I mentioned doing it myself to my propane supplier (who doesn't "do work inside the house"), they nearly had a stroke.

Re: OT-Propane Plumbing

#2

Re: OT-Propane Plumbing

Howard Norman-Prescott, AZ

>I have done propane piping in my own house without any problems. Just be sure that you leak test every connection after you are finished. You want a shut off valve in the propane line to the cook top. The last connection will be a flexible line made for gas cook tops. I did the cook top and the propane furnace in my house. The propane hot water heater was done by the guy that hooked the house up to the propane tank.

Did I say to leak test everything when you are done?

Howard

Re: OT-Propane Plumbing

#3

Re: OT-Propane Plumbing

Lee Schierer - McKean, PA

>Instead of running black pipe, have you considered running flexible copper tubing? Far less likely to have a leak along the run as you should only have teh two fittings at teh ends to contend with.

lee

Re: OT-Propane Plumbing

#4

Re: OT-Propane Plumbing

John in New Mexico

>You're right, its not rocket science. BUT propane leaks in a house are extremely dangerous because propane is heavier than air so it tends to aggregate in low areas rather than dispersing. I suspect thats why they nearly had a stroke when you mentioned doing it yourself. I wouldn't hesitate to do my own work, being careful to use valves and pipe dope designed for gas, and being sure to pressure check the system when finished. I don't know what the time and pressure specs are for propane, and I suspect you may have a hard time finding them, but I'd try about 60 psi overnight myself (thats what I did for my water lines). Perhaps someone else will have better info on that score.

John

Re: OT-Propane Plumbing

#5

If you follow all this advice...I have one more...

SanMan

>.....make sure you get the site utilities located BEFORE you dig anywhere and make sure you bury the new propane line per code restrictions.

There are rules for this for good reason....prevention of an explosion.

I cant tell you how many times I've heard of people not following the proper burial guidelines.

Re: OT-Propane Plumbing

#6

Re: OT-Propane Plumbing

Larry Clinton At Frankfort (Central)., Indiana

>A few tips � but first my experience � I worked for a propane company for about a year (Hicksgas in Indiana) and installed HVAC and appliances for Sears for about 20 years (as a side job). You are correct in believing you can do the job yourself if you take a few precautions. First, where you are not passing through a wall, copper tubing, type L with flare fittings, is allowed � black pipe is also approved but it is more susceptible to leaks due to all the joints required. Make sure you check all your �flares� for cracks prior to assembly. Purchase Rectoseal pipe sealant (I believe I use # 3 � check the can for �approved for propane) and gas leak detection solution. The Rectoseal is far better at sealing pipe threads than Teflon tape. The gas leak detection solution is more accurate in finding small leaks than dish soap / water mix. Limit the number of gas shutoff valves to the minimum required. These are the culprit in 95% of the leaks found in installations. When I worked for the propane company, we were not allowed to use the corrugated flexible lines for the appliance hookup, although some are now listed as approved for this use. We used the Type L copper and coiled a length behind movable appliances like ranges. It is flexible enough to allow them to be pulled out for servicing without damage to the line. When you finish the job � be sure to apply leak detector to ALL fittings and completely around any gas shutoff's. Large leaks will show up as big bubbles immediately � go back and visually inspect all joints / valves about 10 minutes later as small leaks will cause �foam� around any bad joints.

Re: OT-Propane Plumbing

#7

Re: OT-Propane Plumbing

Wayne in Topanga

>Be sure and pressure test. Ask your building inspector for the leak test specifications.

Oh, by the way before you pressure test remove all the gas plug valves and install caps. I found out the hard way that these valves will leak at the test pressure and you will never pass the leak test DAMHIKT.

Good luck,

Wayne

Re: OT-Propane Plumbing

#8

60 lbs is a little overkill

Randy Johnson Connersville, IN

>I work for a natural gas company and the standard is ten pounds/ten minutes. With even a VERY small fizzer you are going to see a drop in that short of time. Remember, that water pressure is measured in pounds whereas gas pressure is normally four ounces. I'm not sure what propane pressure is but it would have to be in the same ballpark because the valves are the same for both. While going as high as 60 pounds might not hurt anything, at the same time it might cause problems that would not have happened at a lower pressure that is still several thousand percent of operating pressure.

The gas valves btw are why you should shut off all shut off valves nearest each appliance before an air test. Most of these valves are designed for ounces. If you shoot pounds to them you might be replacing an expensive part. If a shut off valve leaks it should be replaced. They are cheap.

Re: OT-Propane Plumbing

#9

Thats good to know...

John in New Mexico

>

Re: OT-Propane Plumbing

#10

Re: OT-Propane Plumbing

Dave Bair, Eaton Rapids, MI

>Thanks to all. I found a mechanical contractor who wasn't too busy to do a small job, sort of. He'll fit me in between one of his AC repair jobs. I just have to be home when he has an hour to spare. But I'm retired, so that shouldn't be a big problem. I know my wife is happier with this setup.